|
US$169.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email.
FZ/T 95004-2007: Textile machinery and accessories. Cones for cross winding dyeing process. Technology terms
Status: Valid FZ/T 95004: Evolution and historical versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | Status | PDF |
| FZ/T 95004-2007 | English | 169 |
Add to Cart
|
3 days [Need to translate]
|
Textile machinery and accessories. Cones for cross winding dyeing process. Technology terms
| Valid |
FZ/T 95004-2007
|
| FZ/T 95004-1994 | English | 239 |
Add to Cart
|
2 days [Need to translate]
|
Cones for Cross Winding Dyeing
| Obsolete |
FZ/T 95004-1994
|
PDF similar to FZ/T 95004-2007
Basic data | Standard ID | FZ/T 95004-2007 (FZ/T95004-2007) | | Description (Translated English) | Textile machinery and accessories. Cones for cross winding dyeing process. Technology terms | | Sector / Industry | Spinning & Textile Industry Standard (Recommended) | | Classification of Chinese Standard | W95 | | Classification of International Standard | 59.120.50 | | Word Count Estimation | 6,623 | | Date of Issue | 2007-05-29 | | Date of Implementation | 2007-11-01 | | Older Standard (superseded by this standard) | FZ/T 95004-1994 | | Quoted Standard | GB/T 153; GB/T 191; GB/T 2828.1; GB/T 2829; GB/T 4892; GB/T 6543-1986 | | Regulation (derived from) | NDRC Notice No. 32 of 2007 | | Issuing agency(ies) | National Development and Reform Commission of the People's Republic of China | | Summary | This standard specifies the conical cross-wound bobbin dyeing classification, requirements, test methods, inspection rules, packaging and identification. This standard applies to half cone angle of 4 �� 20 '. The winding width not exceeding l-25mm conical cross- wound bobbin dyeing (hereinafter referred to as " stain tapered tube "). This standard also applies to half- cone angle of 3 �� 30 ', 5 �� 57'. The winding width not exceeding L-25MM dyeing conical tube. | FZ/T 95004-2007: Textile machinery and accessories. Cones for cross winding dyeing process. Technology terms
---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.
Textile machinery and accessories. Cones for cross winding dyeing process. Technology terms
ICS 59.120.50
W95
People's Republic of China textile industry standards
Replacing FZ/T 95004-1994
Textile machinery and accessories stained with cross winding
Conical bobbin technical conditions
Posted 2007-05-29
2007-11-01 implementation
National Development and Reform Commission, People's Republic of China released
Foreword
Instead of the standard FZ/T 95004-1994 "cross winding winder stained with conical tubes" in the part, not instead of involving content
And stained with a conical cross-wound bobbin main dimensions, tolerances and marking. GB/T 20035-2005 is half cone angle of 3 ° 30 ', 4 ° 20'
And 5 ° 57 'with a conical cross-wound bobbin dimensions, tolerances and national standards mark. GB/T 20035.4-2005 a half cone angle
4 ° 20 'stained with conical bobbin dimensions, tolerances and the national standards. Listed below are the national standards and the corresponding structure
International standards.
GB/T 20035-2005 "Textile machinery and accessories with a conical cross-wound bobbin"
--- Part 1. Recommended main dimensions value (ISO 8489-1.1995, IDT);
--- Part 2. half cone angle of 3 ° 30 'cone bobbin dimensions, tolerances and marking (ISO 8489-2.1995, IDT);
--- Part 3. half cone angle of 4 ° 20 'cone bobbin dimensions, tolerances and marking (ISO 8489-3.1995, IDT);
--- Part 4. half cone angle of 4 ° 20 'stained with conical bobbin dimensions, tolerances and marking (ISO 8489-4.1995, IDT);
--- Part 5. half-cone angle of 5 ° 57 'cone bobbin dimensions, tolerances and marking (ISO 8489-5.1995, IDT).
Compared with this standard FZ/T 95004-1994, the main changes are as follows.
a) expanding stained with conical bobbin half cone angle range, not only applies to 4 ° 20 ', but also to 3 ° 30' and 5 ° 57 ';
b) by deleting according to the pipe material, the half cone angle of the conical bobbin dyeing classification regulations and related Figure 1, Table 1;
c) the deletion of the "method of dyeing conical tube labeled" requirement;
d) increasing the "basic dimensions dyeing cone bobbin, limit deviations" and its measuring "gauge dimensions, tolerances and the use of" should
Comply with GB/T 20035.4-2005 in chapter 5;
e) In the inspection rules, add "There is one or more than one failure, is substandard goods," the decision rule;
f) In the inspection rules, add "In a sample of units" description;
g) In the inspection rules, the type of test items to increase the quality of testing, the substandard quality level of 20, classified as substandard C;
h) by deleting the chapter on packaging box predetermined and packaging Pictorial marking tied;
i) by deleting "Appendix A inner diameter measuring method";
j) other necessary editorial changes.
The standard proposed by China Textile Industry Association.
This standard by the National Standardization Technical Committee Textile machinery and accessories.
This standard by the Shaanxi Institute of Textile Equipment, Zhejiang Sanyou Plastic Industry Co., Ltd. is responsible for drafting.
The main drafters of this standard. Zhao Yusheng, water conservancy Hou, Zhang Nan, Jiangchuan Liang.
This standard replaces the standards previously issued as follows.
--- FJ1023-1981, FJ1127-1981;
--- FZ/T 95004-1994.
Textile machinery and accessories stained with cross winding
Conical bobbin technical conditions
1 Scope
This standard specifies the cross-wound conical bobbin dyeing classification, requirements, test methods, inspection rules, packaging and identification.
Called "stained tapered pipe").
2 Normative references
The following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent
Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research
Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard.
GB/T 153 conifer sawmills
GB/T 191 Packaging - Pictorial signs
GB/T 2828.1 Sampling procedures for inspection - Part 1. by acceptance quality limit (AQL) retrieval batch inspection sampling plan
(ISO 2859-1.1999, IDT)
GB/T 2829 periodic inspection Sampling procedures and tables (suitable for process stability test)
GB/T 4892 hard straight cube transport packaging size series
GB/T 6543-1986 corrugated boxes
GB/T 6544-1999 corrugated cardboard packaging material
GB/T 20035.4-2005 Textile machinery and accessories conical bobbin with cross winding - Part 4. half cone angle of 4 ° 20 'staining
With conical bobbin dimensions, tolerances and marking
Category 3
Depending on environmental requirements, divided into common type (codenamed P) and high temperature, high pressure type (code N) staining conical tube.
4 Requirements
4.1 P-type stain conical tubes under normal pressure, N type at a temperature of 120 ℃ dispersion of the dye in the dye continuous cooking 2h, should be no distortion, no
Corrosive, non-staining.
4.2 Semi basic dimensions cone angle 4 ° 20 'stained conical tube, limit deviations shall comply with GB/T 20035.4-2005 provisions; half cone angle
3 ° 30 ', 5 ° 57' and the basic size limit deviation dyeing conical tube should refer to GB/T 20035.4-2005 OK.
4.3 the same batch, the same quality of dyed conical tube sizes average quality of its deviation should be ± 5%.
4.4 staining conical tube end faces, the inner and outer surfaces and perforations should be round and smooth, there should not be worried about the fiber burrs.
4.5 plastic colorant staining conical tube should be good migration resistance, the same batch should be no color.
5 Test methods
5.1 Environmental conditions test reactor or under simulated conditions.
5.2 staining conical inner diameter should be GB/T 20035.4-2005 in Chapter 5, "gauge dimensions, tolerances, and use" measure, other
Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of FZ/T 95004-2007_English be delivered?Answer: Upon your order, we will start to translate FZ/T 95004-2007_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time. Question 2: Can I share the purchased PDF of FZ/T 95004-2007_English with my colleagues?Answer: Yes. The purchased PDF of FZ/T 95004-2007_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to [email protected]. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. Question 5: Should I purchase the latest version FZ/T 95004-2007?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version FZ/T 95004-2007 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.
|