PDF FZ/T 93019-2004 English (FZ/T 93019-1993: Older version)
Search result: FZ/T 93019-2004 (FZ/T 93019-1993 Older version)
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Name of Chinese Standard | Status |
| FZ/T 93019-2004 | English | 80 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Flat fillet clothing for carding process
| Valid |
| FZ/T 93019-1993 | English | 239 |
Add to Cart
|
2 days
|
Flat Fillet Clothing for Carding Process
| Obsolete |
PDF Preview: FZ/T 93019-2004
FZ/T 93019-2004: PDF in English (FZT 93019-2004) FZ/T 93019-2004
FZ
TEXTILE INDUSTRY STANDARD OF
THE PEOPLE’S REPUBLIC OF CHINA
ICS 59.120.20
W 93
Replacing FZ/T 93019-1993
Flat fillet clothing for carding process
ISSUED ON. AUGUST 15, 2004
IMPLEMENTED ON. JANUARY 1, 2005
Issued by. National Development and Reform Commission of the
People’s Republic of China.
Table of Contents
Foreword ... 3
1 Scope ... 5
2 Normative references ... 5
3 Terms and definitions ... 6
4 Classification and marks... 6
5 Requirements ... 7
6 Test methods ... 8
7 Inspection rules ... 8
8 Packaging, symbols and storage ... 10
Foreword
This Standard replaces FZ/T 93019-1993 Flat clothing for carding process.
Compared with FZ/T 93019-1993, the major changes of this Standard are as
follows.
— MODIFY the name of this Standard.
— ADD the “Normative references” (SEE Chapter 2 of this version).
— ADD the “Terms and definitions” (SEE Chapter 3 of this version).
— MODIFY the “Classification and marks” (Section 3.1 of the 1993 version;
Sections 4.1 and 4.2 of this version).
— SIMPLIFY the requirements for the limit deviations of the basic
dimensions of the flat clothing. DELETE the grading rules (Section 4.1
of the 1993 version; Section 5.1 of this version).
— MODIFY the requirements for the tip flatness. DELETE the grading
rules (Section 4.2 of the 1993 version; Section 5.2 of this version).
— DELETE the requirements for the distance between carding pin and
side clip (Section 4.3 of the 1993 version).
— MODIFY the provisions on the tip hardness range of the carding pins.
DELETE the grading rules (Section 4.4 of the 1993 version; Section 5.3
of this version).
— SIMPLIFY the test methods. DELETE the appendix (Section 5.1 of the
1993 version; Sections 6.1 to 6.5 of this version).
— MODIFY and IMPROVE the “Inspection rules” (Chapter 6 of the 1993
version; Chapter 7 of this version).
— MODIFY the “Packaging, symbols and storage” (Chapter 7 of the 1993
version; Chapter 8 of this version).
This Standard was proposed by China National Textile and Apparel Council.
This Standard shall be under the jurisdiction of the Shaanxi Textile Equipment
Research Institute.
Main drafting organizations of this Standard. Shaanxi Textile Equipment
Research Institute, Shanghai Far East Card Clothing Co., Ltd, Wuxi Owl
Flat fillet clothing for carding process
1 Scope
This Standard specifies the terms, definitions, classification, marks,
requirements, test methods, inspection rules, symbols, packaging and
storage of the flat fillet clothing for carding process (hereinafter referred to as
“flat clothing”).
This Standard is applicable to the flat clothing using the fillet clothing as
carding element.
2 Normative references
The provisions in the following documents become the provisions of this
Standard through reference in this Standard. For dated references, the
subsequent amendments (excluding corrections) or revisions do not apply to
this Standard. However, parties who reach an agreement based on this
Standard are encouraged to study if the latest versions of these documents
are applicable. For undated references, the latest versions apply to this
Standard.
GB/T 191 Packaging – Pictorial marking for handling of goods
GB/T 347 Card wire
GB/T 2828.1 Sampling procedures for inspection by attributes – Part 1.
Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot
inspection
GB/T 2829 Sampling procedures and tables for periodic inspection by
attributes (Apply to inspection of process stability)
GB/T 4340.1 Metallic materials – Vickers hardness test – Part 1. Test
method
GB/T 4892 Dimensions of rigid rectangular packages – Transport
packages
GB/T 6543 Corrugated boxes
GB/T 12339 Inner packaging materials in preservation
5.3 The hardness in the position which is 0.5mm under the tip of the carding
pin of the flat clothing after heat treatment shall not be lower than 720HV0.2.
The hardness difference of the same pair of flat clothing shall not be greater
than 60HV0.2. The hardness of the tips without heat or special treatment
shall be determined by the manufacturing plant.
5.4 The pin density of the flat clothing shall be 97% to 105% of the
theoretical value.
5.5 The carding pins shall be neatly arranged on the base fabric. The tips
and bodies of the carding pins shall be clean and without any rust. The tips
shall have no barbs.
6 Test methods
6.1 MEASURE the basic dimensions according to the specified measuring
tools as follows.
a) USE a common normal micrometer to measure the total height;
b) USE a steel tape to measure the total width;
c) USE a vernier caliper to measure the total length and wire setting length;
d) USE a special goniometer to measure the rake angle.
6.2 The tip flatness error shall be determined by the measurements of the
total height, which is the range of the total height of the same pair of card
clothing.
6.3 DETERMINE the Vickers hardness of the carding pins according to the
relevant provisions of the GB/T 4340.1.
6.4 USE a vernier caliper to measure and to calculate the pin density.
6.5 USE the visual observation method for appearance quality inspection.
7 Inspection rules
7.1 General
7.1.1 The flat clothing shall be conducted with the following categories of
inspection.
– Type inspection;
The basic dimensions of the packages shall conform to the provisions of the
GB/T 4892 as far as possible.
8.2 Symbols
8.2.1 Product symbols
Each box of flat clothing shall have 1 to 2 product labels that are not easy to
be stained, along with the following indications.
a) manufacturing plant’s name or trademark;
b) product symbol; and
c) manufacturing date or batch number.
8.2.2 Packaging symbols
There shall be packaging symbols (delivering symbol for transport packages,
and pictorial marking for handling of goods) on the transport packages. The
contents shall conform to the provisions in Sections 8.2.2.1 and 8.2.2.2.
8.2.2.1 Delivering symbol for transport packages.
a) manufacturing plant’s name and trademark;
b) product symbol;
c) manufacturing date or batch number;
d) exit-factory date;
e) number of each pair; and
f) gross weight.
8.2.2.2 Pictorial marking for handling of goods
The symbols of “KEEP DRY” and “FRAGILE” shall conform to the provisions
in the GB/T 191.
8.3 Storage
8.3.1 The manufacturing plant shall conduct adequate anti-rust treatment to
the flat clothing, and shall ensure that no rusting will be caused by improper
anti-rust treatment within one year from the date of exiting the factory.
......
Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.
|