JJF 1109-2003_English: PDF (JJF1109-2003)
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | Status | PDF |
| JJF 1109-2003 | English | 269 |
Add to Cart
|
3 days [Need to translate]
|
Calibration Specification for Concentricity Tester
| Valid |
JJF 1109-2003
|
Standards related to: JJF 1109-2003
| Standard ID | JJF 1109-2003 (JJF1109-2003) | | Description (Translated English) | Calibration Specification for Concentricity Tester | | Sector / Industry | Metrology & Measurement Industry Standard | | Classification of Chinese Standard | A52 | | Word Count Estimation | 10,143 | | Date of Issue | 2003-09-23 | | Date of Implementation | 2004-03-23 | | Older Standard (superseded by this standard) | JJG 88-1983 | | Drafting Organization | Beijing Institute of Measurement Science | | Administrative Organization | National Technical Committee geometric length measurement | | Regulation (derived from) | State Administration of Quality Supervision, Inspection and Quarantine Notice 2003 No. 106 | | Issuing agency(ies) | State Administration of Quality Supervision, Inspection and Quarantine | | Summary | This standard applies to gear beating tester and deflection tester calibration. | JJF 1109-2003
Calibration Specification for Concentricity Tester
National Metrology Technical Specification of the People's Republic
Beat tester calibration specification
Released on.2003-09-23
2004-03-23 implementation
The General Administration of Quality Supervision, Inspection and Quarantine issued
Beat tester calibration specification
Concentricity
Tester
Replace JJG88-1983
This specification was approved by the General Administration of Quality Supervision, Inspection and Quarantine on September 23,.2003, and
It will take effect on March 23,.2004.
Focal Point. National Geometric Length Measurement Technical Committee
Main drafting unit. Beijing Institute of Metrology
Participated in drafting unit. China Institute of Metrology
This specification entrusts the focal point to be responsible for interpretation
The main drafters of this specification.
Xia Yang (Beijing Institute of Metrology)
Cui Zhenyu (Beijing Institute of Metrology)
Participate in the drafters.
Zhang Wei (China Institute of Metrology)
Li Rui (China Institute of Metrology)
table of Contents
1 range (1)
2 Citations (1)
3 Overview (1)
4 Measurement characteristics (2)
4.1 indicator table (2)
4.2 Parallelism of the longitudinal movement of the two top center lines to the slide (2)
4.3 Positional repeatability (2)
4.4 Parallelism of the fixed tip to the center of the active tip to the guide rail (2)
4.5 indication error (2)
5 Calibration conditions (2)
5.1 Environmental conditions (2)
5.2 Standard and other major equipment (3)
6 Calibration items and calibration methods (3)
6.1 Calibration of the indicator table (3)
6.2 Parallelism of the longitudinal movement of the two top center lines to the slide (3)
6.3 Positional repeatability (3)
6.4 Parallelism of the fixed tip to the center of the active tip to the guide rail (3)
6.5 indication error (3)
7 Calibration result expression (4)
8 re-study interval (4)
Appendix A Calibration Certificate Page Format (5)
Beat tester calibration specification
1 Scope
This specification applies to the calibration of the gear runout tester and the yaw tester.
2 Citations
The provisions contained in the following documents constitute provisions of this specification by reference in this specification. Publication of this specification
The version shown is valid. All standards, specifications or procedures will be revised and all parties using this specification should
Use the possibility of the latest version of the following literature.
JJF 1001-1998 General measurement terms and definitions
JJF 1059-1999 Measurement Uncertainty Evaluation and Representation
GB/T 10095.2-2001 Involute cylindrical gears - Accuracy Part 2. Radial comprehensive deviation and radial runout
Definition and allowable value
GB/T 13924-1992 Involute cylindrical gear precision inspection specification
GB/T 15481-2000 General requirements for calibration and inspection laboratory capabilities
JJG34-1996 indication table (percent dial and dial gauge) verification procedures
JJG39-1990 Mechanical comparator calibration procedures
3 Overview
This type of instrument is mainly used to measure the ring runout of cylindrical gears, bevel gears and worm gears, as well as shafts, discs, etc.
The radial circular runout of the rotating parts is shown in Figure 1, Figure 2.
Figure 1 Gear Beat Checker
...
|