GB/T 30002-2024 PDF EnglishUS$275.00 · In stock · Download in 9 seconds
GB/T 30002-2024: General technical requirements for children’s toothbrushes Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 30002: Historical versions
Similar standardsGB/T 30002-2024: General technical requirements for children’s toothbrushes---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT30002-2024GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 11.060.20 CCS Y 89 Partially replacing GB 30002-2013, GB 30003-2013 General Technical Requirements for Children’s Toothbrushes Issued on: NOVEMBER 28, 2024 Implemented on: DECEMBER 1, 2025 Issued by. State Administration for Market Regulation; Standardization Administration of the People’s Republic of China. Table of ContentsForeword... 3 1 Scope... 5 2 Normative References... 5 3 Terms and Definitions... 5 4 Classification... 6 5 Requirements... 6 6 Test Methods... 9 7 Inspection Rules... 12 8 Marking, Packaging, Transportation and Storage... 14 Annex A (Informative) Schematic Diagram of Brush Head of Children’s Toothbrush ... 16 General Technical Requirements for Children’s Toothbrushes1 ScopeThis Document specifies the sensory quality, specifications and dimensions, and the like technical requirements, as well as the inspection rules, marking, packaging, transportation and storage of children's toothbrushes (hereinafter referred to as "toothbrushes"); provides classifications benefiting the technical provisions; and describes the corresponding test methods. This Document applies to the production, inspection and sale of toothbrushes for children aged 14 and below.2 Normative ReferencesThe provisions in following documents become the essential provisions of this Document through reference in this Document. For the dated documents, only the versions with the dates indicated are applicable to this Document; for the undated documents, only the latest version (including all the amendments) is applicable to this Document. GB/T 191 Packaging – Pictorial Marking for Handling of Goods GB/T 2828.1 Sampling procedures for inspection by attribute - Part1.Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection GB/T 2829 Sampling procedures and tables for periodic inspection by attributes (Apply to inspection of process stability) GB/T 4208-2017 Degrees of protection provided by enclosure (IP code) GB/T 19342-2024 Manual toothbrushes - General requirements and test methods GB 39669 General technical requirements for safety of toothbrushes and oral implements GB/T 40362-2021 Powered toothbrushes - General requirements and test methods3 Terms and DefinitionsFor the purposes of this Document, the terms and definitions given in GB 39669, GB/T 19342- 2024, and GB/T 40362-2021 apply.4 Classification4.1 According to the driving mode, they can be divided into manual toothbrushes and electric toothbrushes. 4.2 According to the shape of the brush head, they can be divided into toothbrushes with conventional brush head, toothbrushes with cylindrical brush head, and toothbrushes with U- shaped brush head, etc., see Appendix A for examples.5 Requirements5.1 Sensory quality The sensory quality shall meet the requirements of 4.1 in GB/T 19342-2024. 5.2 Specifications and dimensions 5.2.1 The specifications and dimensions of toothbrushes with conventional brush head shall meet the requirements of Table 1; and the dimension diagram is shown in Figure 1. 5.2.2 The specification and dimension of toothbrush with cylindrical brush head shall meet the requirements of Table 2.See Figure 1 for the dimension diagram. It shall meet the requirements of 5.3.3 in GB/T 40362-2021. 5.11 Service life of electric toothbrush switch It shall meet the requirements of 5.4 in GB/T 40362-2021. 5.12 Waterproof performance of electric toothbrush Electric toothbrush with non-replaceable battery shall be able to work normally after test in 6.13. 5.13 Dropping performance of electric toothbrush It shall work normally after test in 6.14; and the firmness and waterproof performance of detachable brush head shall meet the requirements of 5.10 and 5.12. 5.14 Noise of electric toothbrush It shall meet the requirements of 5.5 in GB/T 40362-2021.6 Test Methods6.1 Specimen conditioning and test environment The sample conditioning shall be conducted in an environment with a temperature of (23±2)℃ and a relative humidity of (50±10)% for no less than 4 h; and the test shall be carried out under such environmental conditions (unless otherwise specified). 6.2 Sensory quality 6.2.1 Visually inspect the sample at a distance of 300 mm from the sample under natural light or a light source with a color temperature of 6500 K. 6.2.2 Use an absorbent cotton fully soaked in 65% ethanol to apply a force of 1 N~1.5 N to wipe the brush head, brush handle, bristles and trims back and forth 100 times, at a wiping frequency of 2 times/s~3 times/s; and visually observe whether there is color on the absorbent cotton. 6.2.3 Check the bubbles in the brush handle by comparing with the dust standard chart. 6.2.4 Use the sense of smell to judge whether there is obvious odor. 6.3 Specifications and dimensions The length of hair side, width of hair side, thickness of brush head, bristle height, and total length of the toothbrush are measured by a measuring tool with a minimum graduation value of no more than 0.02 mm; and the single filament diameter is measured at the root by a measuring tool with a minimum graduation value of no more than 0.001 mm. 6.4 Hair tuft strength The hair tuft strength is assessed by the hair tuft bending force and is tested according to the method in Annex A of GB/T 19342-2024. 6.5 Sharpening rate It shall be tested according to the method in 5.5 of GB/T 19342-2024. 6.6 Breaking strength of molded bristles It shall be tested according to method 5.6 of GB/T 19342-2024. 6.7 Bending recovery rate of single filament Manual toothbrushes are tested according to method in 5.7 of GB/T 19342-2024; and electric toothbrushes are tested according to method in 6.4.2 of GB/T 40362-2021. 6.8 Temperature resistance 6.8.1 Test device. Constant temperature water tank with temperature control accuracy of ±2 ℃. 6.8.2 Test steps. For manual toothbrushes, immerse the specimen in water at (50±2) ℃ for 20 min; take it out and then check the handle, brush head and bristles for any abnormality. For electric toothbrushes, remove the brush head and immerse it in water at (50±2) ℃ for 20 min; take it out and then check the brush head and bristles for any abnormality. 6.9 Bending resistance of handle 6.9.1 Test device. Tensile testing machine with a minimum graduation value of 0.1 N, equipped with a reverser and a clamp. Sample support, the distance between the two support points is 50 mm, see Figure 2.The top pressure rod, the top is a hemispherical shape with a radius of 6 mm. 6.9.2 Test steps. Mark the test section on the specimen; the length of the test section is 50 mm; and the starting point is 40 mm from the top of the brush head. Place the specimen on the sample support (with the bristles facing downward); the two ends of the test section are respectively aligned with two support points of the base; and the top pressure rod acts vertically on the center of the test section; the specific position is shown in Figure 2.Start the tensile testing machine, and let the top pressure rod drop 25 mm at a uniform speed of (50±10) mm/min. During the descent of the top pressure rod, record the tensile machine reading when the specimen breaks as the bending force of handle. If the specimen does not break during the descent of the top pressure rod and the tensile machine reading has reached 60 N, the test shall be stopped and the recorded result shall be "the bending force of the handle is no less than 60 N". If the specimen still does not break when the top pressure rod is lowered to 25 mm, the test shall be stopped and the recorded result shall be "no break within the deformation limit". ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 30002-2024 be delivered?Answer: The full copy PDF of English version of GB/T 30002-2024 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 30002-2024_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 30002-2024_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 30002-2024 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 30002-2024?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 30002-2024 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 30002-2024?A step-by-step guide to download PDF of GB/T 30002-2024_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 30002-2024". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
