GB 31892-2015 PDF English
| Standard ID | USD | BUY PDF | Delivery | Standard Title (Description) | Status |
| GB 31892-2015 | 85 | Add to Cart | Auto, 9 seconds. | General Safety Specification of Umbrellas | Valid |
Similar standards
GB 31892-2015: General Safety Specification of Umbrellas
---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GB31892-2015GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 97.180 Y 89 General Safety Specification of Umbrellas Issued on. SEPTEMBER 11, 2015 Implemented on. APRIL 1, 2017 Issued by. State Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China; Standardization Administration of the People's Republic of China.
Table of Contents
Foreword... 3 1 Application Scope... 4 2 Normative References... 4 3 Terms and Definitions... 5 4 Classification... 5 5 Requirements... 5 6 Test Method... 7 7 Inspection Rules... 10 8 Marking, Packaging, Transportation and Storage... 12Foreword
Chapter 5 of this Standard is compulsory; the others are voluntary. This Standard was drafted in accordance with the rules given in GB/T 1.1-2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. The institution issuing this document shall not be held responsible for identifying any or all such patent rights. This Standard was proposed by China National Light Industry Council. This Standard shall be under the jurisdiction of the National Standardization Center of Sundry Articles. The drafting organizations of this Standard. Hangzhou Paradise Umbrella Group Co., Ltd., Sun City Outdoor Products Technology Co., Ltd., Beijing 1st Institute of Quality Supervision and Inspection of Light Industrial Products, Yuzhongniao (Fujian) Outdoor Products Co., Ltd., Jiangxi Qinde Industrial Co., Ltd., Zhejiang Hongye Umbrella Co., Ltd., Fulong (Fujian) Umbrella Co., Ltd., Zhejiang Friendship Feinuo Umbrella Co., Ltd., Shaoxing Jinding Umbrella Co., Ltd., Quanzhou Hongli Umbrella Co., Ltd., Rixin Textile Co., Ltd., Susino Umbrella Co., Ltd., Zhejiang Tianwei Umbrella Co., Ltd., Jinjiang Jialemei Umbrella Co., Ltd., Fujian Jicheng Umbrella Co., Ltd., Fujian Yusimeng Umbrella Co., Ltd., Hongtai (Fujian) Rain Gear Parts Co., Ltd., Swift (Fujian) Umbrella Co., Ltd. and Xiamen Tongan Hexin Umbrella IND. Co., Ltd. The main drafters of this Standard. Li Chuanhe, Wang Qiwei, He Lingjun, Cai Rongtuan, Ding Jingtang, Cai Jinbang, Yu Chengrong, Wang Wenbi, Lv Miaofen, Lv Xinmiao, Lv Yayan, Lv Shiliang, Wang Anbang, Pan Wei, Xiao Qingjiang, Huang Wenji, Liu Jishan, Cai Rongyong, Xu Youcan, Lu Jingxiang, Wu Hengyou, Zhou Xiaomei, Wei Xiaoying, Wang Xinyao, Cheng Xiaohu and Zhao Peng. General Safety Specification of Umbrellas1 Application Scope
This Standard specified the term and definition, product classification, requirements, test method, inspection rules and marking, packaging, transportation and storage of umbrellas. This Standard applies to handheld umbrella and fixed umbrella whose umbrella cover and stand are made of different materials. This Standard does not apply to children umbrellas.2 Normative References
The following referenced documents are indispensable for the application of this document. For dated references, only the edition dated applies to this document. For undated references, the latest edition of the referenced documents (including all amendments) applies to this Standard. GB/T 2828.1-2012, Sampling procedures for inspection by attributes – Part1. Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection GB/T 2829-2002, Sampling procedures and tables for periodic inspection by attributes (Apply to inspection of process stability) GB/T 2912.1, Textiles – Determination of formaldehyde – Part 1.Free and hydrolyzed formaldehyde (water extraction method) GB 4706.1, Safety of household and similar electrical appliances – Part 1.General requirements3 Terms and Definitions
For the purpose of this document, the following term and definition applies. 3.1 pinch point a point causing injury because of being pinched by two rigid parts4 Classification
4.1 They can be divided in accordance with the forms of opening and closing into hand-open and hand-close umbrella, hand-open and auto-close umbrella, auto-open and hand-close and auto-open and auto-close umbrella. 4.4 Handheld umbrella can be divided into all-weather umbrella, plastic umbrella, oilcloth umbrella, paper umbrella, art umbrella and so on. 4.5 Fixed umbrella can be divided into beach umbrella, garden umbrella and so on.5 Requirements
5.1 Umbrella cap or top (ferrule) 5.2 Tip 5.2.1 The end face of the tip of handheld umbrella shall be spherical or cambered; the diameter of the tip shall not be less than 8 mm. 5.2.2 For the products of handheld umbrella which are made by nesting the shaft and tip, the depth of the shaft stretching into the tip shall not be less than 10 mm. 5.3 Requirements for safety in use 5.3.1 The metal wire head shall not be exposed; there shall be no sharp end or sharp edge which can be touched in use and cause injuries to human body. 5.3.2 No pinch point shall be generated in normal use. 5.3.3 The positioning device for opening and closing umbrella is reliable which shall not be out of control; during the test process specified in 6.3.3, the auto-open and handheld umbrella and the auto-open and auto-close umbrella will not be open if the button is not pressed. 5.4 Parts binding fastness 5.5 Limit of hazardous substances 5.5.1 Hazardous elements in handle The soluble antimony, arsenic, barium, cadmium, chromium, mercury, selenium or any soluble chemical compound formed by these elements shall not exceed the numerical values specified in Table 1. 5.5.2 Migratable lead content of the cover of oilcloth umbrella and paper umbrella The migratable lead content of the cover of oilcloth umbrella and paper umbrella shall not be greater than 90 mg/kg. 5.6 Ultraviolet protection of the cover For the products with the ultraviolet protection, the UPF shall be greater than 40 and the T (UVA)AV less than 5%. 5.7 Wind resistance strength For beach umbrella, garden umbrella, all-weather umbrella and oilcloth umbrella, no defect which will cause human injuries shall occur in the rib or rod after the test specified in 6.7.6 Test Method
6.1 Umbrella cap or umbrella top (ferrule) 6.2 Tip 6.2.1 Carry out visual inspection for the end face of the tip of handheld umbrella; use a Vernier calliper with the minimum division value 0.02 mm to measure the diameter of the tip directly. 6.3 Requirements for safety in use 6.3.1 Carry out visual inspection and hand-feeling inspection. 6.3.2 Carry out visual inspection and hand-feeling inspection during the opening and closing process to examine whether there is any pinch point. 6.3.3 Grip the handle to rotate for 3 times to and fro; open and close umbrella for 5 times; and observe whether it is out of control. 6.4 Parts binding fastness Beach umbrella and garden umbrella shall be tested in accordance with GB/T 23103- 2008.All-weather umbrella and plastic umbrella shall be tested in accordance with GB/T 23147-2008.Art umbrella shall be tested in accordance with QB/T 4151-2010. 6.5 Limit of hazardous substances 6.5.1 Hazardous elements shall be tested in accordance with GB 6675.4-2014. 6.5.2 Migratable lead content shall be tested in accordance with GB 6675.4-2014. 6.5.3 Formaldehyde content shall be tested in accordance with GB/T 2912.1. 6.5.4 Decomposable hazardous aromatic amine shall be tested in accordance with GB/T 17592. 6.6 Ultraviolet protection of the cover It shall be tested and evaluated in accordance with GB/T 18830. 6.7 Wind resistance strength7 Inspection Rules
7.1 Exit-factory inspection 7.1.1 Any product to be delivered shall pass exit-factory inspection. The product can only be delivered after being qualified by the production quality inspection department in accordance with this Standard and shall be accompanied by qualification inspection marking. 7.2 Type inspection In mm 7.2.1 A type inspection shall be carried out in one of the following circumstances. 7.2.2 The samples for the type inspection shall be taken from the qualified batches which pass the exit-factory inspection, 7 in number. The evaluation of the type inspection is based on the unqualified number. 7.2.3 For the type inspection, use the one-time sampling plan of discrimination level I in accordance with GB/T 2829-2002.See Table 3 for the inspection items, requirements, test methods, rejectable quality level values, sample sizes and discrimination arrays. 7.2.4 Limit of hazardous substances shall be as specified in 5.5; or else, the type inspection is determined to be a fail. 7.2.5 The type inspection is determined to be a fail if one item is a fail.8 Marking, Packaging, Transportation and Storage
8.1 Marking 8.1.1 Each umbrella shall be provided with the following information in Chinese. 8.1.2 The boxes for the products shall be provided with the following information in Chinese. 8.3 Transportation The products shall be handled with care, which shall not be pressed by heavy weight. 8.4 Storage The products shall be stored in a dry, ventilated warehouse. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
