GB 32284-2015 PDF EnglishUS$150.00 · In stock · Download in 9 seconds
GB 32284-2015: Minimum allowable values of energy efficiency and energy efficiency grades for petrochemical centrifugal pumps Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
GB 32284-2015: Minimum allowable values of energy efficiency and energy efficiency grades for petrochemical centrifugal pumps---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GB32284-2015 NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 27.010 F 01 Minimum allowable values of energy efficiency and energy efficiency grades for petrochemical centrifugal pumps ISSUED ON: DECEMBER 10, 2015 IMPLEMENTED ON: JANUARY 01, 2017 Issued by: General Administration of Quality Supervision, Inspection and Quarantine of the PRC; Standardization Administration of the PRC. Table of ContentsForeword ... 3 1 Scope ... 4 2 Normative references ... 4 3 Terms and definitions ... 5 4 Technical requirements ... 5 Appendix A (Informative) Calculation method of energy efficiency grades for pumps ... 12 Appendix B (Informative) Calculation method of target minimum allowable values of energy efficiency for pumps ... 14 Minimum allowable values of energy efficiency and energy efficiency grades for petrochemical centrifugal pumps1 ScopeThis Standard specifies the basic requirements for petrochemical centrifugal pumps (hereinafter referred to as “pumps”), efficiency calculation methods for pumps, energy efficiency grades for pumps, minimum allowable values of energy efficiency for pumps, target minimum allowable values of energy efficiency for pumps, and evaluating values of energy conservation for pumps. This Standard applies to single-stage single-suction pumps and single-stage double-suction pumps with closed (maximum) impellers installed which deliver clean liquids. This Standard does not apply to clean-water centrifugal pumps, non-metallic centrifugal pumps, and seal-less rotodynamic pumps.2 Normative referencesThe following documents are indispensable for the application of this document. For the dated references, only the editions with the dates indicated are applicable to this document. For the undated references, the latest edition (including all the amendments) are applicable to this document. GB/T 3215 Centrifugal pumps for petroleum petrochemical and natural gas industries GB/T 3216 Rotodynamic pumps - Hydraulic performance acceptance tests - Grades 1, 2 and 3 GB/T 5656 Technical specification for centrifugal pumps - Class II GB/T 7021 Glossary of terms for centrifugal pump GB/T 13006 NPSH for centrifugal, mixed flow and axial flow pump3 Terms and definitionsThe terms and definitions as defined in GB/T 7021 and the following ones apply to this document. 3.1 Specified point The point on the pump performance curve determined by the specified flow and the specified head. 3.2 Minimum allowable values of energy efficiency for pumps The minimum efficiency of the specified point allowed under the test conditions specified by the standard. 3.3 Target minimum allowable values of energy efficiency for pumps The minimum efficiency of the specified point allowed after the implementation of this Standard for a certain period of time. 3.4 Evaluating values of energy conservation for pumps The minimum efficiency of the specified point which shall be achieved to meet the energy conservation certification requirements under the test conditions specified by the standard.4 Technical requirements4.1 Basic requirements 4.1.1 The design and manufacture of the pumps should meet the requirements of GB/T 3215 or GB/T 5656. 4.1.2 Unless otherwise agreed with the user, the required NPSH (NPSHR) of the pump’s specified point shall comply with the provisions of GB/T 13006. 4.1.3 The test methods of the pumps shall comply with the provisions of GB/T 3216. The allowable tolerance coefficient of the flow (Q), head (H), efficiency (η), and NPSHR of the pump shall comply with Grade 2 regulations of GB/T 3216. 4.2 Calculation methods of pump efficiency and specific speed 4.2.1 Calculation of pump efficiency Pump efficiency is a percentage of the ratio of pump output power (effective n - Speed, in revolutions per minute (r/min). 4.3 Energy efficiency grades for pumps The energy efficiency grades for pumps are divided into 3 grades, of which 1 is the highest and 3 is the lowest. The energy efficiency grades for pumps are determined according to Table 1. When the flow is greater than 3000 m3/h, the energy efficiency grade for pump is determined according to the flow Q=3000 m3/h. For an example of calculation method of energy efficiency grades for pumps, see Appendix A. 4.4 Minimum allowable values of energy efficiency for pumps The minimum allowable values of energy efficiency for pumps shall not be lower than the energy efficiency grade 3 η3 of Table 1. 4.5 Target minimum allowable values of energy efficiency for pumps When the flow is in the range of 5 m3/h~3000 m3/h, the target minimum allowable value ηT0 of energy efficiency for pumps is determined as follows: a) When 120≤ns≤210, any target minimum allowable value (ηT0) of energy efficiency in the specific speed range shall be found in Figure 1 (or Table 2); b) When 20≤ns< 120 and 210< ns≤300, for any target minimum allowable value (ηT) of energy efficiency in the specific speed range, ηT0 shall be found in Figure 1 (or Table 2); then according to Figure 2 (or Table 3) and Figure 3 (or Table 3) respectively, FIND Δη. Then according to formula (4), calculate ηT. Where: ηT - Target minimum allowable value of energy efficiency for pump when 20≤ns< 120 and 210< ns≤300; ηT0 - Target minimum allowable value of energy efficiency for pump when 120≤ns≤210; Δη - Pump efficiency correction value when 20≤ns< 120 and 210< ns≤300. For an example of calculation method of target minimum allowable values of energy efficiency for pumps, see Appendix B.Appendix A(Informative) Calculation method of energy efficiency grades for pumps A.1 Example The performance of the specified point of a single-stage double-suction petrochemical centrifugal pump is: Q=800 m3/h, H=12 m, n=1470 r/min. Calculate the efficiency value η1 of energy efficiency grade 1, the efficiency value η2 of energy efficiency grade 2, and the efficiency value η3 of energy efficiency grade 3. A.2 Calculate the specific speed ns of pump Substitute the above example data into formula (3) to calculate: A.3 Calculate the efficiency values of energy efficiency grades for pumps A.3.1 Calculate the efficiency value η1 of energy efficiency grade 1 for pump The efficiency value η1 of energy efficiency grade 1 for pump may be calculated as follows: a) FIND the reference value η; According to Figure 1 (or Table 2), when Q=800 m3/h, η=81.9%. b) Determine the efficiency correction value Δη; According to Figure 3 (or Table 3), when ns=277.4, Δη=2.1%. c) Calculate the efficiency value η0 of specified point of pump; d) Calculate the efficiency value η1 of grade 1 for pump; According to Table 1, when Q=800 m3/h, the efficiency value of energy efficiency grade 1 is: ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB 32284-2015 be delivered?Answer: The full copy PDF of English version of GB 32284-2015 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB 32284-2015_English with my colleagues?Answer: Yes. The purchased PDF of GB 32284-2015_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB 32284-2015 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB 32284-2015?A step-by-step guide to download PDF of GB 32284-2015_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB 32284-2015". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |