HJ 2512-2012_English: PDF (HJ2512-2012)
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | Status | PDF |
| HJ 2512-2012 | English | 629 |
Add to Cart
|
5 days [Need to translate]
|
Technical requirement for environmental labeling products. Printers, Fax machines, Multifunction devices
| Valid |
HJ 2512-2012
|
Standards related to: HJ 2512-2012
| Standard ID | HJ 2512-2012 (HJ2512-2012) | | Description (Translated English) | Technical requirement for environmental labeling products. Printers, Fax machines, Multifunction devices | | Sector / Industry | Environmental Protection Industry Standard | | Classification of Chinese Standard | L63 | | Classification of International Standard | 35.180 | | Word Count Estimation | 24,248 | | Older Standard (superseded by this standard) | HJ/T 302-2006 | | Quoted Standard | GB 20943; GB 25956-2010; GB/T 16288; GB/T 16685-2008; GB/T 18313-2001; GB/T 18455; GB/T 22372; HJ/T 238; HJ 570-2010; HJ 573 - 2010; QB/T 2342; ISO/IEC 28360-2007 | | Drafting Organization | China-Japan Friendship Center for Environmental Protection | | Regulation (derived from) | Department of Environmental Protection Notice 2012 No. 25; | | Summary | This standard specifies the printers, fax machines and multifunction machines for environmental labeling products terms and definitions, basic requirements, technical contents and test method. This standard applies to 220V, 50Hz power grid under normal op | HJ 2512-2012
Technical requirement for environmental labeling products.Printers, Fax machines, Multifunction devices
National Environmental Protection Standard of the People's Republic
Technical requirements for environmental labeling products
Printers, fax machines and all-in-ones
Technical requirement for environmental labeling products
Printers, Fax machines, Multifunction devices
Published on.2012-03-30
2012-06-01 Implementation
Ministry of Environmental Protection released
HJ □□□□-201□
Content
Foreword..3
1 Scope.4
2 Normative references. 4
3 Terms and Definitions 4
4 basic requirements.5
5 Technical content.5
6 Test methods.9
Appendix A (Normative Appendix) “Product Environmental Design” Requirements.10
Appendix B (Normative) Phthalate banned in plastic parts..13
Appendix C (Normative) Restricted use of polycyclic aromatic hydrocarbons (PAHs) .14
Appendix D (informative) Calculation method for carbon dioxide emissions 24
Appendix E (Normative) TVOC, benzene and styrene inspection procedures..15
Appendix F (Normative Appendix) Ozone Inspection Procedures..19
Appendix G (Normative Appendix) Dust Inspection Procedures.21
HJ □□□□-201□
Foreword
To reduce the production and use of printers, fax machines and all-in-one products in order to implement the Environmental Protection Law of the People's Republic of China
This standard is formulated to affect the environment and human health during the process and to protect the environment.
This standard applies to energy consumption, noise, toxic and hazardous substances, environmental design, and raw materials for printers, fax machines, and all-in-ones.
Requirements for production processes, recycling and reuse, and specifications.
This standard refers to the German Environmental Labeling Foundation (Basic Criteria for Award of the Environmental)
Label Office Equipment with Printing (Printer, Copier, Multifunction) (Office Equipment with Printing)
Function (Printers, Copiers, Multifunction Devices)) (RAL-UZ 122,.2009), and the Japan Environmental Association
Environmental Labeling Agency "Eco-label type NO.122" "Printer Version2.2.2010" for "Environmental Label Product Certification Technology"
The printer, fax machine and all-in-one machine (HJ/T 302-2006) was revised.
The main changes in this standard compared to HJ/T 302-2006 are as follows.
-- Added definitions for printers, fax machines, etc.;
-- Revised the requirements for environmental design;
-- Revised the requirements for pollutant discharge;
-- Revised the requirements for the use of toxic and hazardous substances;
-- Revised the regulations for product energy consumption;
-- Increased requirements for carbon dioxide emissions from products;
-- Increased requirements for adapter energy consumption;
-- Increased the requirements for double-sided printing devices;
-- Increased requirements for consumables
-- Revised the requirements for noise during the use of the product;
-- Revised the standard appendix.
This standard applies to China Environmental Labeling Product Certification and China Environmental Labeling Low Carbon Product Certification.
This standard was formulated by the Science and Technology Standards Department of the Ministry of Environmental Protection.
This standard is mainly drafted by. China-Japan Friendship Environmental Protection Center, National Office Equipment and Consumables Quality Supervision and Inspection Center.
This standard was approved by the Ministry of Environmental Protection on March 30,.2012.
This standard has been implemented since June 1,.2012.
This standard is explained by the Ministry of Environmental Protection.
The previous versions of the standards replaced by this standard are.
--HBC 36-2005, HJ/T 302-2006.
HJ □□□□-201□
Environmental labeling products technical requirements printers, fax machines and all-in-ones
1 Scope of application
This standard specifies the terms and definitions, basic requirements, and technical requirements of printers, fax machines, and all-in-one environmental labeling products.
Capacity and test methods.
This standard applies to the normal operation of 220V, 50Hz power supply, standard format printers, fax machines and to print or pass
A versatile machine that is essential for basic functions, including the use of stylus, inkjet, electrostatic imaging, thermal transfer, thermal, thermal sublimation, solid
A product such as a body spray wax.
2 Normative references
The contents of this standard refer to the terms in the following documents. For undated references, the valid version applies to this standard.
GB 20943 Single output AC-DC and AC-AC external power supply energy efficiency limit value and energy saving evaluation value
GB 25956-2010 Energy efficiency limit value and energy efficiency rating of printers and fax machines
GB/T 16288 logo for plastic products
GB/T 16685-2008 Information technology - Measuring methods for the throughput of printing equipment - 1
GB/T 18313-2001 Measurement of airborne noise of acoustic information technology equipment and communication equipment
GB/T 18455 packaging recycling mark
GB/T 22372 monochrome black and white laser printer test version
HJ/T 238 Environmental Labeling Product Technical Requirements Rechargeable Battery
HJ 570-2010 Environmental Labeling Product Technical Requirements Toner Cartridge
HJ 573-2010 Environmental Labeling Products Technical Requirements
QB/T 2342 copy paper
ISO /IEC 28360.2007 Determination of chemical emission rates in electronic equipment for office equipment
3 Terms and definitions
GB 25956-2010 and the following terms and definitions apply to this standard.
3.1 printer printers
Receiving information from a computer interface, a web interface, or a digital device port, and outputting it to an image output device such as paper
Ready.
3.2 fax machine fax machines
HJ □□□□-201□
An image reproducing apparatus whose function is to transmit or receive graphic information. Such machines must be able to pass data from the original image.
The telecommunications network is transmitted to similar devices.
3.3 Multifunction devices
It comes standard with printing or faxing, and also has one or more functions for copying, scanning, printing, and faxing.
Ready.
3.6 Printing/Fax Speed Note 1, 2 printing/fax speed
The number of pages per minute of product printing/fax A4 size paper (single-sided black and white mode) in ppm. This standard uses ν.
Note 1. For continuous paper feed products and dot matrix printers, print/fax speed is taken (16× (maximum media width (unit. m) × maximum print speed (single
Bit. m/min)).
Note 2. For products with only color printing/fax function, the print/fax speed is the speed in color single-sided mode.
3.7 Standard format standard format
Standard format refers to discontinuous paper feed products with a maximum media media width between 210.0mm and 356.0mm (eg A3, A4, B4,
Letter paper, etc.), the continuous media feed product has a maximum media medium width between 210.0mm and 406.0mm.
3.8 components units/component parts
It consists of two or more parts that are combined with each other by force or shape.
3.9 protective parts defending/case parts
Protect the device from the external environment while preventing users from accessing moving parts, illuminated parts or high voltage parts
component.
3.10 recycled paper recycled paper
Refers to paper products made from a certain proportion of recycled pulp. This standard refers to the use of copy paper with a recycled pulp content of more than 30%.
4 basic requirements
4.1 Product quality, safety performance, electromagnetic compatibility and pollutant control shall comply with the requirements of the corresponding standards.
4.2 Pollutant emissions from product manufacturing enterprises shall comply with the requirements of national or local pollutant discharge standards.
4.3 Product manufacturers should strengthen clean production in the production process.
5 Technical content
5.1 Product Environmental Protection Design Requirements
5.1.1 The product environment design should meet the requirements of Appendix A.
5.1.2 Deca-BDE and SCCPs shall not be used for the outer casing, protective parts and the substrate of the circuit board.
HJ □□□□-201□
5.1.3 Plastic parts with a mass greater than 25g shall not be used except for the plastic parts adjacent to the heating and imaging components in the outer casing and protective parts.
For chlorine-containing and bromine-containing polymers, flame retardants containing organochlorine compounds and organic bromine compounds should not be added.
5.1.4 In addition to wire and cable, the phthalates listed in Appendix B shall not be used in plastic parts with a mass greater than 25g.
Plasticizer.
5.1.5 Tributyltin (TBT) and triphenyltin (TPT) shall not be used in product parts.
5.1.6 The total amount of benzo(a)pyrene in the product casing, various types of buttons and external power cord shall not exceed 20 mg/kg, as listed in Appendix C.
The sum of 16 polycyclic aromatic hydrocarbons (PAHs) should not exceed.200 mg/kg.
5.1.7 The battery included in the product shall comply with the requirements of HJ/T 238.
5.1.8 The toner cartridge for the product shall meet the requirements of clauses 5.1, 5.2, 5.3, 5.5, 5.6, 5.7 of HJ 570-2010.
5.1.9 The inkjet cartridges for the product shall meet the requirements of clauses 5.1, 5.2, 5.3, 5.5, 5.6, 5.7 of HJ 573-2010.
5.2 Product production stage requirements
5.2.1 Do not use hydrochlorofluorocarbons (HCFCs), 1,1,1-trichloroethane (C2H3Cl3), trichloroethylene (C2HCl3), dichloroethane
(CH3CHCl2), dichloromethane (CH2Cl2), chloroform (CHCl3), carbon tetrachloride (CCl4), bromopropane (C3H7Br), etc.
The substance acts as a cleaning solvent.
5.2.2 Lead-free soldering process should be used during component assembly and connection.
5.3 Product requirements
5.3.1 Hazardous substance discharge requirements
5.3.1.1 Dust, ozone, total volatile organic compounds (TVOC) during use and standby of electronic image printing products
The styrene and benzene emissions should meet the requirements of Table 1.
Table 1 Product Hazardous Substance Emission Limits for Electronic Image Printing
Target substance
Emission limit (mg/h)
Black and white printer color printer
Dust ≤4.0 ≤4.0
Ozone ≤1.5 ≤3.0
Total volatile
Organic compound
Object (TVOC)
Working ≤10 ≤18
In standby
Volume>
0.25m3 ≤2.0 ≤2.0
Volume ≤
0.25m3 ≤1.0 ≤1.0
Styrene ≤1.0 ≤1.8
Benzene < 0.05 < 0.05
HJ □□□□-201□
5.3.1.2 Other (needle-type, inkjet, thermal transfer, thermal, sublimation) printing mode of the product in use and standby process
The emission of volatile organic compounds (TVOC) should not exceed 18 mg/h. Needle-type printing method for the product in use
Do not put more than 4.0 mg/h.
5.3.2 The noise generated when the product is working at the highest print speed (inkjet products are in the default mode) shall meet the requirements of Table 2.
Table 2 Noise limits generated when the product is operating at the highest print speed (ν, ppm)
Product Type Sound Power LWA, dB(A) Note 1, 2
Black and white monochrome ≤59+0.35×ν
Color ≤61+0.30×ν
Stylus printer ≤70
Note 1. For serial color products, if the color printing/fax speed ≤ 0.5 black and white monochrome printing/fax speed, the sound power level should be given
It is true that only the noise measurement of black and white monochrome printing speed is performed.
Note 2. The maximum noise limit for black and white monochrome and color products shall not exceed 75 dB(A).
5.3.3 Energy requirements
5.3.3.1 The energy consumption of products with a printing speed not exceeding 70ppm shall meet the requirements of the secondary energy efficiency standard in GB 25956-2010.
5.3.3.2 Printing speeds greater than 70ppm using thermal, thermal sublimation, electronic imaging, solid spray wax, thermal transfer technology and high performance inkjet
The technical energy consumption of monochrome printers and fax machines should meet the requirements of Table 3. The energy consumption of other products should meet the highest in GB 25956-2010.
Requirements for secondary energy efficiency standards as specified by the speed segment and operating mode power limits.
Table 3 Typical energy consumption limits for monochrome printers and fax machines
Product Type Print/Fax Speed (ν)/ppm Typical Energy/kWh
Monochrome printer, monochrome fax machine 70< ν≤82 < 0.35 ×ν-10.3
ν>82 < 0.70 ×ν-39.0
5.3.4 Adapter requirements
5.3.4.1 For products equipped with adapters, the average efficiency rating of the adapter shall meet the requirements of Table 4.
Table 4 Average efficiency energy efficiency limit
Output power nominal value (P0)/W minimum average efficiency
Output voltage ≥6V Output voltage < 6V
0< P0< 1 0.480×P0 0.140 0.497×P0 0.067
1≤P0< 49 0.0626×ln P0 0.622 0.0750×ln P0 0.561
49≤P0≤250 0.870 0.860
5.3.4.2 For products equipped with adapters, the energy efficiency limit of the adapter under no-load condition shall meet the requirements of Table 5.
HJ □□□□-201□
Table 5 No-load state energy efficiency limit value
Output power nominal value (P0)/W Maximum active power in no-load state
AC-AC adapter AC-DC adapter
1≤P0< 49 0.5 0.3
49≤P0≤250 0.5 0.5
5.3.5 Double-sided printing requirements
The two-sided printing function configuration using electrostatic imaging printing is shown in Table 6. The product using continuous printing paper does not apply to this item.
Table 6 Double-sided printing function requirements for printers and all-in-ones using electrostatic imaging printing
Product type product printing speed (ν)/(ppm) double-sided printing device requirements
Monochrome printer
24< ν< 45 Optional
≥ ≥ 45 standard
color printer
19< ν< 40 Optional
ν ≥ 40 standard
5.3.6 The product can be printed on recycled paper. The performance of the paper should meet the QB/T 2342 standard. Products using continuous printing paper are not applicable.
This item.
5.4 Product Packaging Requirements
5.4.1 Hydrochlorofluorocarbons (HCFCs) should not be used as blowing agents.
5.4.2 The total amount of heavy metals such as lead, cadmium, mercury and hexavalent chromium in packaging and packaging materials shall not exceed 100 mg/kg.
5.4.3 It should be marked in accordance with GB/T 18455.
5.5 Product recycling phase requirements
The enterprise shall establish a recycling and recycling treatment system for the toner cartridges and ink cartridges provided by the waste products and the original equipment.
Information on product recycling and recycling.
5.6 Product Description Requirements
Product descriptions must be sold with the product and should include the following.
a) product maintenance instructions;
b) that equipment with noise greater than 63 dB(A) should have recommendations for placing the equipment in relatively independent areas;
c) information on the product's duplex unit, or optional double-sided unit information;
d) information on recycled paper is recommended;
e) When using or printing a large number of documents for a long time in a room with poor ventilation, it is recommended that the user change the air in time;
f) Product power-saving mode, standby mode and zero energy consumption only when the product is connected without any external input power
HJ □□□□-201□
State of affairs;
g) product recycling information and corresponding channels;
h) Recycling information for used toner cartridges and inkjet cartridges.
5.7 Supply Guarantee
5.7.1 Maintenance Guarantee
The company shall undertake to provide spare parts that may damage the product within the normal use range for at least 5 years after the production is stopped.
5.7.2 Supply of consumable materials
The company shall undertake to provide the consumables of the product for at least 5 years after the product is discontinued.
6 Test methods
6.1 Technical content The inspection of TVOC, benzene and styrene in Article 5.3.1 shall be carried out in accordance with the method specified in Appendix D; the inspection of ozone shall be in accordance with Appendix E.
The prescribed method is carried out; the dust is tested in accordance with the method specified in Appendix F.
6.2 Technical content 5.3.2 Inspection shall be carried out in accordance with the provisions of 6 of GB/T 18313-2001. The following conditions shall be met first when testing.
a) The noise shall be checked under the factory default conditions and no additional accessories are involved;
b) Monochrome products should be tested in monochrome test version GB/T 22372 or GB/T 18313-2001, color products should be used
ISO /IEC 28360.2007 color test version for testing;
c) testing with the paper of the product's nominal maximum paper width (the thermal product uses its designated paper);
d) testing with paper having a basis weight of 60-80 g/m2;
e) If a single product is used for testing, it should be determined by adding 3dB(A) to the test result.
6.3 Technical content The inspection of 5.3.3 shall be carried out in accordance with the method specified in GB 25956-2010, and the carbon dioxide emissions shall be in accordance with Appendix G.
Calculation.
6.4 Technical content 5.3.4 Inspection shall be carried out in accordance with the method specified in GB 20943.
6.5 Other requirements in the technical content are verified by document review in conjunction with on-site verification.
HJ □□□□-201□
Appendix A
(normative appendix)
"Product Environmental Design" requirements
Classification number requires object description
structure
And even
Pick up
Various materials made of mutually incompatible materials
Components can be separated or easily separated
The auxiliary part of the connection is connected.
Protective parts, bottom
Block, electrical and electronic
Component, toner cartridge
Ink box
2 Electrical and electronic components and electrical and electronic components are easy to find and separate.
Equipment as a whole, package
Light bulbs --
3 Disintegration for the purpose of recycling can be accomplished with only general tools.
Shell, base,
Electrical and electronic components
"General tools" means that they can be bought on the market.
Tool of. According to relevant standards and regulations
Not applicable when selecting a specific connection.
4 Consider the point and space required to understand the body tool during design.
Protective parts, bottom
Block, electrical and electronic
Component
5 Screws for fixing components can be removed with only up to 3 tools
Protective parts, bottom
Block, electrical and electronic
Component
Tool type by tool type (eg cross slot)
And the size of the tool is determined.
6 One person can complete the disintegration. Machine
For example, when the undercut angle is greater than or equal to 90 degrees,
Can have multiple sliding in the same direction at the same time
But it may not be broken down by one person. When necessary
Decompose more than 3 slide-in combinations at the same time
When deemed, it does not meet the requirements.
There are no electronic components on the housing. But solid
The operating part that is fixed on the outer casing, and
Housings that have a base function are not suitable.
Protective parts --
The production enterprise shall be as follows from 1 to 7
The order was disintegrated and recorded
point.
Machine --
material
Selection
Choose
mark
Plastic parts with similar functions only make
Use 1 material. Reused parts are not
Be applicable.
More than 25g of defense
Protective parts, base,
Mechanical Parts
“Similar function” means “impact resistance”,
"Abrasion resistance" and other functions.
10 Plastics with a mass greater than 25g should use a monomer or copolymer. shell--
Made of a plastic case with a mass greater than 25g
The type of monomer or copolymer used is not
It should be more than 4 types and easy to disintegrate.
shell--
HJ □□□□-201□
Classification number requires object description
Table with mass greater than 25g and maximum plane
Plastic parts with an area exceeding.200mm2
According to the requirements of GB/T 16288
Remember.
Plastic parts --
For the label on the product casing that is not easy to peel off
Sign, should use the same as the paste
Material or material that does not affect recycling
material.
label--
14 Plastic housing parts must not be plated. shell--
(a) Painting of plastic parts is limited to
To be minimal (example manufacturer name).
Laser marking, etc. are not included in this project.
And "painting". Reused parts are not
Be applicable.
Protective parts, drum
The powder box and ink tank coating include a paint layer, an evaporation layer, and printing.
(b) During the painting process, it should be used.
Resist the paint. Recommended to improve the coating
Labor safety and health strip
And reduce environmental load.
Protective parts, drum
Powder box, ink tank
“Coating material that does not hinder reuse” means painted
Parts and materials are compatible with the coating, coated
It does not hinder the reuse of product materials.
"Improving the safety of the painting workers
"conditions" refers to the ventilation of the painting workplace
Wind and workers should use protective equipment.
“Reducing environmental load” means reducing to the atmosphere
Discharge VOC, in the setting of the processing equipment,
The painting process is laid out and used low
VOC discharges paint, etc.
As long as any one of (a) and (b) is satisfied.
17 Use of renewable materials and materials to connect
Protective parts, bottom
Block, toner cartridge prevention
Protective parts, ink tank
Protective parts
“Recyclable materials” means that they can be used for raw
Production of the same recycled materials as the starting materials
Use on the level).
And, this project only examines the design intent and purpose.
The standard does not examine whether it has been recycled.
Allow the use of recycled plastic as raw material
a part of.
(Inkjet printer is not applicable)
Protective parts, bottom
Seat, toner cartridge
“Allow” means according to the design requirements of the product,
As long as it is a material that meets the conditions, it can be made
use. “Partial” means the presence of the corresponding plastic zero
Piece is OK (not necessarily for all parts).
19 Parts and materials in Schedule A.1 are easily removed. Machine --
20 Based on the records from 15 to 19, the material selection was recorded.
Housing, base, drum
Powder box ink box --
HJ □□□□-201□
Classification number requires object description
long
use
In addition to standard parts
In addition, more than 50% of the parts can be used for this system.
The same generation of manufacturers, the same performance
His products.
Machine --
May allow and remanufacture
(reprocessed) module or reuse
Parts (not for inkjet printers).
Machine
The manufacturer should allow reuse. Its purpose can
Is the repair spare part or the same quality as the new zero
Equivalent to new.
23 toner cartridges and ink cartridges can be reused
Toner cartridge, ink
Box, simple container
except
It means that the design should not hinder reuse.
Schedule A.1 Shaped articles, chemicals and parts to be separated
*Capacitor with PCB
*Uses mercury-containing parts like lamps for backlights
*battery
* Printed circuit board with an area of more than 10cm2
* Toner cartridge, powder, color paste, liquid toner. Also includes color toner.
*Used plastic parts containing brominated flame retardants
* LCD screen with an area of more than 100cm2 (sometimes fixed on the case)
*External power cord
* Capacitors containing hazardous substances (height > 25mm, diameter > 25mm or volume close to this)
HJ □□□□-201□
Appendix B
(normative appendix)
Phthalate banned in plastic parts
Chinese name English name abbreviation
Diisoisophthalate Di-iso-nonylphthalate DINP
Di-n-octylphthalate DNOP
Di-(2-ethylhexy)-phthalate DEHP
Diisoisylphthalate DIDP
Butylbenzylphthalate BBP
Dibutylphthalate DBP
HJ □□□□-201□
Appendix C
(normative appendix)
Restricted use of polycyclic aromatic hydrocarbons (PAHs)
Chinese name English name abbreviation
Naphthalene Napene Nap
Terenaphthylene AcPy
苊Acenaphthene Acp
芴Fluorene Flu
Philippine Phenanthrene PA
蒽Anthracene Ant
Fluoranthine Fluoranthene FL
芘Pyrene Pyr
1,2-benzophenanthrene Chrysene CHR
Benzo(a)蒽Benzo[a]anthracen BaA
Benzo(b)fluoranthene Benzo[b]fluoranthene BbF
Benzo(k)fluoranthene Benzo[k]fluoranthene BkF
Benzo(a)芘Benzo[a]pyrene BaP
Dibenzo[a, h)蒽Dibenzo[a,h]anthrancene DBA
茚(1,2,3-cd)芘Indeno[1,2,3-cd]pyrene IND
Benzo(g,h,i)苝 (perylene) Benzo[g,h,i]perylene BghiP
HJ □□□□-201□
Appendix D
(normative appendix)
Inspection procedures...
...
|