|
US$339.00 · In stock
Delivery: <= 4 days. True-PDF full-copy in English will be manually translated and delivered via email.
GB/T 39166-2020: Test method of mechanized peel for resistance spot, projection and seam welds
Status: Valid
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | Status | PDF |
| GB/T 39166-2020 | English | 339 |
Add to Cart
|
4 days [Need to translate]
|
Test method of mechanized peel for resistance spot, projection and seam welds
| Valid |
GB/T 39166-2020
|
PDF similar to GB/T 39166-2020
Basic data | Standard ID | GB/T 39166-2020 (GB/T39166-2020) | | Description (Translated English) | Test method of mechanized peel for resistance spot, projection and seam welds | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | J33 | | Classification of International Standard | 25.160.40 | | Word Count Estimation | 18,145 | | Date of Issue | 2020-10-11 | | Date of Implementation | 2021-05-01 | | Regulation (derived from) | National Standard Announcement No. 21 of 2020 | | Issuing agency(ies) | State Administration for Market Regulation, China National Standardization Administration | GB/T 39166-2020: Test method of mechanized peel for resistance spot, projection and seam welds---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.
Test method of mechanized peel for resistance spot, projection and seam welds
ICS 25.160.40
J33
National Standards of People's Republic of China
Mechanical peel test method for resistance spot welding, projection welding and seam welding joints
2020-10-11 released
2021-05-01 implementation
State Administration for Market Regulation
Issued by the National Standardization Management Committee
Table of contents
Foreword Ⅰ
1 Scope 1
2 Normative references 1
3 Terms and definitions 1
4 Equipment 2
5 Sample 3
6 Test procedure 7
7 Repeat test 8
8 Test report 8
Appendix A (informative appendix) Structural changes of this standard compared with ISO 14270.2016 9
Appendix B (informative appendix) The technical differences between this standard and ISO 14270.2016 and their reasons list 10
Appendix C (informative appendix) The influence of solder joint position on test results 11
Appendix D (informative appendix) Example of bending method 12
Appendix E (informative appendix) Measurement of bending center position of bending system 14
Appendix F (Normative Appendix) Seam Welding Dimensions Measurement 16
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
This standard uses the redrafting method to amend and adopt ISO 14270.2016 "Destructive Test of Resistance Welding Seam Resistance Spot Welding, Seam Welding"
Specimen dimensions and procedures for mechanical peeling test of projection welded joints.
Compared with ISO 14270.2016, this standard has many structural adjustments. Appendix A lists this standard and ISO 14270.2016.
A list of changes in the chapter number
Compared with ISO 14270.2016, this standard has technical differences, and the clauses involved in these differences have been passed in the outer margins.
The set vertical single line (|) is marked, and Appendix B gives a list of the corresponding technical differences and their reasons.
This standard also made the following editorial changes.
---Modified the standard name;
---References are deleted.
This standard was proposed and managed by the National Welding Standardization Technical Committee (SAC/TC55).
Drafting organizations of this standard. CRRC Dalian Locomotive and Rolling Stock Co., Ltd., Harbin Welding Research Institute Co., Ltd., Fuyang Shengda, Anhui Province
Machinery Co., Ltd., Shanghai Materials Research Institute, CRRC Qingdao Sifang Locomotive and Rolling Stock Co., Ltd., CRRC Changchun Rail Vehicle Co., Ltd.
Company, Dongying Yuanjie Petroleum Machinery Co., Ltd., Dongfeng Motor Group Co., Ltd. Passenger Vehicle Company.
The main drafters of this standard. Liao Rongqi, Ma Yiming, Li Jingying, Jiang Yinglong, Wang Bin, Su Jinhua, Li Gangqing, Zhang Yong, Li Haiwei, Zhang Ligui.
Mechanical peeling of resistance spot welding, projection welding and seam welding joints
experiment method
1 Scope
This standard specifies the mechanical peeling test equipment, test equipment and test equipment for the single welding point (weld seam) of resistance spot welding, projection welding and seam welding of metallic materials.
Samples, test procedures, repeated tests and test reports.
This standard applies to metal plates with a thickness of 0.5mm~5.0mm, a maximum solder joint diameter of 7t and less than 12mm (t is the plate thickness, when the plate thickness is
At different times, t is the thickness of the thinner plate) resistance welding joint.
2 Normative references
The following documents are indispensable for the application of this document. For dated reference documents, only the dated version applies to this article
Pieces. For undated references, the latest version (including all amendments) applies to this document.
GB/T 3375 welding terminology
GB/T 16825.1 Inspection of static uniaxial testing machine Part 1.Inspection and calibration of force measuring system of tensile and (or) compression testing machine
Standard (GB/T 16825.1-2008, ISO 7500-1.2004, IDT)
3 Terms and definitions
The following terms and definitions defined in GB/T 3375 apply to this document.
3.1
Mechanical peel test
Mechanical equipment is used to apply the peeling force acting in the thickness direction of the solder joints to conduct destructive tests of resistance welding lap joints.
3.2
Mechanical peel force
The force applied to the specimen during the mechanical peel test.
3.3
Multi-spot welding
Spot welding of two or more welding points with two or more pairs of electrodes at the same time or according to automatic control procedures.
3.4
Solder joint diameter
After the destructive test, without the help of metallographic inspection, the average diameter of the melting area measured on the bonding surface.
3.5
Minimum seam welding width
During seam welding, the minimum nugget width measured on the bonding surface.
Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 39166-2020_English be delivered?Answer: Upon your order, we will start to translate GB/T 39166-2020_English as soon as possible, and keep you informed of the progress. The lead time is typically 2 ~ 4 working days. The lengthier the document the longer the lead time. Question 2: Can I share the purchased PDF of GB/T 39166-2020_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 39166-2020_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to [email protected]. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.
|