|
US$234.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email.
GB/T 13288.3-2009: Preparation of steel substrates before application of paints and related products -- Surface roughness characteristics of blast-cleaned steel substrates -- Part 3: Method for the calibration of ISO surface profile comparators and for the determination of
Status: Valid
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | Status | PDF |
| GB/T 13288.3-2009 | English | 234 |
Add to Cart
|
3 days [Need to translate]
|
Preparation of steel substrates before application of paints and related products -- Surface roughness characteristics of blast-cleaned steel substrates -- Part 3: Method for the calibration of ISO surface profile comparators and for the determination of
| Valid |
GB/T 13288.3-2009
|
PDF similar to GB/T 13288.3-2009
Basic data | Standard ID | GB/T 13288.3-2009 (GB/T13288.3-2009) | | Description (Translated English) | Preparation of steel substrates before application of paints and related products -- Surface roughness characteristics of blast-cleaned steel substrates -- Part 3: Method for the calibration of ISO surface profile comparators and for the determination of | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | A29 | | Classification of International Standard | 25.220.10 | | Word Count Estimation | 12,168 | | Date of Issue | 2009-03-09 | | Date of Implementation | 2009-11-01 | | Adopted Standard | ISO 8503-3-1988, IDT | | Regulation (derived from) | Announcement of Newly Approved National Standards 2009 No. 2 (total 142) | | Issuing agency(ies) | General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China | | Summary | This standard specifies the line with GB/T 13288. 1 requirements of ISO surface profile comparators for the calibration and surface roughness measurement method Focusing microscope procedure. This section can be used to clean up after spraying substantially planar, the average peak-valley difference in hy = 20��m ~ 200��m range of steel surface roughness measurement. If it is impossible to directly observe the surface roughness should be cleaned in the jet on a substrate surface or a representative copy surface area (see Appendix E) on the determination of surface roughness. An alternative method, see ISO 8503-4. | GB/T 13288.3-2009: Preparation of steel substrates before application of paints and related products -- Surface roughness characteristics of blast-cleaned steel substrates -- Part 3: Method for the calibration of ISO surface profile comparators and for the determination of
---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.
Preparation of steel substrates before application of paints and related products Surface roughness characteristics of blast-cleaned steel substrates Part 3. Method for the calibration of ISO surface profile comparators and for the determination of surf
ICS 25.220.10
A29
National Standards of People's Republic of China
GB/T 13288.3-2009/ISO 8503-3. 1988
Before application of paints and surface treatment of steel
Surface roughness characteristics of blast-cleaned steel post
Part 3. ISO calibration of surface roughness comparison specimens
Registration and surface roughness measurement method
Focusing microscope method
(ISO 8503-3. 1988, IDT)
Posted 2009-11-01 2009-03-09 implementation
Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China
Standardization Administration of China released
Foreword
GB/T 13288 "steel substrates before application of paints and spray cleaned steel surface roughness characteristics" is divided into the following sections.
--- Part 1. Technical requirements for the Assessment of blast - cleaned steel surface roughness of ISO surface profile comparators and
definition;
--- Part 2. Determination after abrasive blast cleaning of steel surface roughness comparison specimens class method;
--- Part 3. Calibration and surface roughness measurement method ISO surface roughness comparison specimens microscope focusing method;
--- Part 4. ISO calibration of surface roughness and surface roughness comparison specimens measuring method stylus method;
--- Part 5. Determination of surface roughness Replica tape method.
This section GB/T 13288 Part 3.
This section identical with ISO 8503-3. 1988 "before and after application of paints and surface treatment of steel surface roughness characteristics of blast - cleaned steel
Part 3. Calibration and surface roughness measurement method ISO surface roughness comparison specimens microscope focusing Law "(in English).
This section is equivalent translation ISO 8503-3. 1988.
For ease of use, this section made the following editorial changes.
--- "This International Standard" be replaced by "this section";
"." --- With a decimal point instead of a comma as the decimal point, "";
--- With a comma "," instead of a comma as described, "";
--- Remove the foreword and introduction of international standards.
This section of the Appendix A, Appendix B and Appendix C are normative appendices, Appendix D and Appendix E is an informative annex.
This part is proposed by the China State Shipbuilding Corporation.
This part of the National Standardization Technical Committee before painting and metal surface treatment and painting processes Technical Committee paint pigment
(SAC/TC5/SC6) centralized.
This section drafted by. China Shipbuilding Technology and Economy Research Institute, China Shipbuilding Industry Corporation 11th Institute, Shandong
Kai Tai Metal Abrasive Co., Ltd.
The main drafters of this section. Song Yanyuan, Fu Jianhua, Liubing Yang, Liuru Wei, Zhao Hongbo, Yin Jianguo.
GB/T 13288.3-2009/ISO 8503-3. 1988
Before application of paints and surface treatment of steel
Surface roughness characteristics of blast-cleaned steel post
Part 3. ISO calibration of surface roughness comparison specimens
Registration and surface roughness measurement method
Focusing microscope method
1 Scope
This section GB/T 13288 specifies the calibration surface and in line with GB/T 13288.1 requirements of ISO surface profile comparators block
Determination of roughness microscope focusing methods.
Roughness measurement. If the surface roughness can not be directly observed, injection should be cleaned on a substrate has a surface area representative or
Determination of surface roughness on a copy of the surface (see Appendix E).
Note. In the right place, this assay can also be used to evaluate the surface roughness by the other abrasive blast cleaning of the substrate.
An alternative method, see ISO 8503-4.
2 Normative references
The following documents contain provisions which, through reference GB/T 13288 in this section constitute provisions of this section. For dated reference documents
Member, all subsequent amendments (not including errata content) or revisions do not apply to this section, however, encouraged to reach under this section
Parties to research agreement to use the latest versions of these documents. For undated reference documents, the latest versions apply to this
section.
Part 1 Steel Surface roughness characteristics of blast - cleaned steel substrates before GB/T 13288.1-2008 coated paint
Score. used to assess the technical requirements and definitions (ISO 8503-1 after blast - cleaned steel surface roughness ISO surface roughness comparison specimens of.
1988, IDT)
ISO 4618 Paints and varnishes - Terms and definitions
ISO 8503-21) steel surface blast cleaned steel substrates before application of paints roughness characteristics - Part 2. Abrasive jet
Determination of surface roughness after exit cleaned steel grade comparison specimen method
ISO 8503-4 steel surfaces coated with paint spray steel surface treatment after cleaning roughness characteristics - Part 4. ISO table
Calibration and surface roughness comparison specimens surface roughness measuring method stylus method
ISO 8504-22) before application of paints and surface treatment of steel surface treatment method - Part 2. Abrasive blast - cleaning
1) GB/T 13288-1991 of reference adopted ISO 8503. 1985.
2) GB/T 18839.2-2002 is equivalent to ISO 8504-2.2000.
3 Terms and Definitions
GB/T 13288.1-2008 and terms and definitions established ISO 4618 applies to GB/T 13288 in this section.
Principle 4
Viewing area the sample surface was observed with a microscope in a predetermined specified. According to the observation area to adjust the focal length of the microscope objective, determined by the same
GB/T 13288.3-2009/ISO 8503-3. 1988
Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 13288.3-2009_English be delivered?Answer: Upon your order, we will start to translate GB/T 13288.3-2009_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time. Question 2: Can I share the purchased PDF of GB/T 13288.3-2009_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 13288.3-2009_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to [email protected]. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.
|