Powered by Google www.ChineseStandard.net Database: 189760 (20 Apr 2024)

GB/T 13025.10-2012 (GBT13025.10-2012)

GB/T 13025.10-2012_English: PDF (GBT 13025.10-2012, GBT13025.10-2012)
Standard IDContents [version]USDSTEP2[PDF] delivered inStandard Title (Description)StatusPDF
GB/T 13025.10-2012English110 Add to Cart 0--9 seconds. Auto-delivery General test method in salt industry -- Determination of ferrocyanide Valid GB/T 13025.10-2012

BASIC DATA
Standard ID GB/T 13025.10-2012 (GB/T13025.10-2012)
Description (Translated English) General test method in salt industry. Determination of ferrocyanide
Sector / Industry National Standard (Recommended)
Classification of Chinese Standard X35
Classification of International Standard 71.060.50
Word Count Estimation 7,747
Older Standard (superseded by this standard) GB/T 13025.10-2003
Quoted Standard GB/T 6682-2008
Drafting Organization National Sea Lake Salt Standardization Center
Administrative Organization National Salt Industry Standardization Technical Committee
Regulation (derived from) National Standards Bulletin 2012 No. 13
Proposing organization China Light Industry Association
Issuing agency(ies) General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China
Summary This standard specifies the ferrous cyanide salt in the test method. The law applies to the part of ferrous sulfate ferrous cyanide content of 1 mg/kg or more sample measured, pyridine pyrazolone law applies to ferrous cyanide content of 1 mg/kg the follo

Standards related to: GB/T 13025.10-2012

GB/T 13025.10-2012
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 71.060.50
X 35
Replacing GB/T 13025.10-2003
General Test Method in Salt Industry -
Determination of Ferrocyanide
ISSUED ON. JUNE 29, 2012
IMPLEMENTED ON. DECEMBER 01, 2012
Issued by. General Administration of Quality Supervision, Inspection and
Quarantine;
Standardization Administration of PRC.
Table of Contents
Foreword ... 3
1 Scope ... 5
2 Normative References ... 5
3 Ferrous Sulfate Method ... 5
4 Pyridine-Pyrazolone Method ... 8
Foreword
This Part is one of the serial standards for general test method in salt industry; currently,
the serial standards can be divided into the following 13 parts; other test method
standards shall be supplemented in the follow-up work.
--- GB/T 13025.1 General Test Method in Salt Industry – Determination of Grain
Size;
--- GB/T 13025.2 General Test Method in Salt Industry – Determination of
Whiteness;
--- GB/T 13025.3 General Test Method in Salt Industry – Determination of Moisture;
--- GB/T 13025.4 General Test Method in Salt Industry – Determination of Insoluble
Matter;
--- GB/T 13025.5 General Test Method in Salt Industry – Determination of Chloride
Ion;
--- GB/T 13025.6 General Test Method in Salt Industry – Determination of Calcium
and Magnesium;
--- GB/T 13025.7 General Test Method in Salt Industry – Determination of Iodide
Ion;
--- GB/T 13025.8 General Test Method in Salt Industry – Determination of Sulfate;
--- GB/T 13025.9 General Test Method in Salt Industry – Determination of Lead;
--- GB/T 13025.10 General Test Method in Salt Industry – Determination of
Ferrocyanide;
--- GB/T 13025.11 General Test Method in Salt Industry – Determination of Fluoride;
--- GB/T 13025.12 General Test Method in Salt Industry – Determination of Barium
Ion;
--- GB/T 13025.13 General Test Method in Salt Industry – Determination of Arsenic.
This Part is Part 10 of GB/T 13025.
This Part was drafted as per the rules specified in GB/T 1.1-2009.
This Part replaces GB/T 13025.10-2003 General Test Method in Salt Industry –
Determination of Potassium Ferrocyanide; this Part made the editorial medication to
GB/T 13025.10-2003.
General Test Method in Salt Industry -
Determination of Ferrocyanide
1 Scope
This Part of GB/T 13025 specifies the test method of determining the ferrocyanide in
the edible salt.
The ferrous sulfate method in this Part is applicable to the determination of samples
with a ferrocyanide content of 1mg/kg above; while the pyridine-pyrazolone method is
applicable to the determination of samples with a ferrocyanide content of 1mg/kg below.
2 Normative References
The following documents are essential to the application of this document. For the
dated documents, only the versions with the dates indicated are applicable to this
document; for the undated documents, only the latest version (including all the
amendments) are applicable to this document.
GB/T 6682-2008 Water for Analytical Laboratory Use - Specification and Test
Methods
3 Ferrous Sulfate Method
3.1 Principle
Under acidic conditions, ferrocyanide reacts with ferrous sulfate t o form a white
precipitate of ferrous ferrocyanide, which is oxidized by air to form Prussian blue and
determined by spectrophotometry.
3.2 Reagents
3.2.1 Reagent specification
Unless otherwise stated, only analytically pure reagents and Class-III water specified
in GB/T 6682-2008 are used in the analysis.
3.2.2 Sodium chloride
Take 50g of sodium chloride; place into high temperature furnace; burn it at 800°C for
30min; cool it off for later-use.
3.2.3 Sulfuric acid solution (1+20)
Take 5mL of concentrated sulfuric acid; slowly place it into 100mL of water; then mix
well.
3.2.4 40g/L ferrous sulfate solution
Take 4g of ferrous sulfate (FeSO4•7H2O); dissolve it in 100mL of sulfuric acid solution
(3.2.3); filter it; store in the brown reagent bottle at low temperature.
3.2.5 Potassium ferrocyanide standard stock solution (1mL of solution contains
1.0mg [Fe(CN)6]4-)
Accurately take 0.1993g of potassium ferrocyanide (K4[Fe(CN)6]•3H2O); add a small
amount of water to dissolve; dilute to 100mL.
3.2.6 Potassium ferrocyanide standard working solution (1mL of solution
contains 50µg [Fe(CN)6]4-)
Pipette 5.00mL of potassium ferrocyanide standard stock solution (3.2.5); dilute to
100mL.
3.3 Instruments
3.3.1 Spectrophotometer.
3.3.2 General laboratory instruments.
3.4 Analytical procedures
3.4.1 Determination of the limit method
Pipette the potassium ferrocyanide standard working solution (3.2.6) corresponding to
the limited amount into 50mL colorimetric tube; add 5g of sodium chloride (3.2.2); add
water to dissolve; add 4mL of ferrous sulfate solution (3.2.4); add water to dilute to the
scale; shake evenly; stand for 10min; take reagent blank as a reference at the
wavelength of 670nm; then measure the absorbance. Take another 50mL colorimetric
tube; take 5.0g of specimen into the colorimetric tube; add 40mL of water to dissolve
(if the solution is turbid, filter with 0.45µm filter membrane); add 4mL of ferrous sulfate
solution (3.2.4); add water to dilute to the scale; shake evenly; stand for 10min; then
take reagent blank as a reference at the wavelength of 670nm; then measure the
absorbance. If the absorbance of the specimen solution is lower than that of the
standard solution, then it is qualified; otherwise, it is disqualified.
3.4.2 Determination of working curve method
4 Pyridine-Pyrazolone Method
4.1 Principle
The ferrocyanide is decomposed into cyanide under acidic conditions; reacts with
chloramine T to form cyanogen chloride (CNCl); then blue dye is formed with pyridine-
pyrazolone; then photometry is used to measure.
4.2 Reagent
4.2.1 Pyridine (GB/T 689)
4.2.2 Chloramine T solution (10g/L)
Take 1.0g of chloramine T; dissolve into 100mL of water.
4.2.3 Phosphate buffer solution
Take 17.8g of anhydrous disodium hydrogen phosphate and 17.0g of anhydrous
potassium dihydrogen phosphate; add water to dissolve and dilute to 500mL.
4.2.4 Sodium hydroxide solution (0.1mol/L)
Take 1.0g of sodium hydroxide; dissolve into 250mL of water.
4.2.5 Acetic acid solution (1mol/L)
Pipette 11.5mL of acetic acid; add water to 200mL; mix evenly.
4.2.6 Tartaric acid solution (10.0g/L)
Take 20.0g of tartaric acid; dissolve into 200mL of water; filter it.
4.2.7 Standard solution
4.2.7.1 Standard stock solution
Take 10.0g of sodium chloride (3.2.2); add 100mL of water to dissolve; add 4.0mL of
potassium ferrocyanide standard working solution (3.2.6); mix evenly; transfer into
500mL distillation flask; add 10mL of tartaric acid solution (4.2.6); quickly connect the
condenser to start distillation. Use 100mL volumetric flask containing 10mL of sodium
hydroxide solution (4.2.4) to collect the distillate; maintain the solution boiling in the
distillation flaks for 10min. After cooling off, take off the volumetric flask; add water to
the scale; shake evenly. 1mL of such solution contains 2.0µg [Fe(CN)6]4-.
4.2.7.2 Standard working solution
...