YB/T 081-2013 PDF in English
YB/T 081-2013 (YB/T081-2013, YBT 081-2013, YBT081-2013)
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Name of Chinese Standard | Status |
| YB/T 081-2013 | English | 70 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Rule for rounding off of numerical values and judgement of testing values for technical standards of metallurgy
| Valid |
| YB/T 081-1996 | English | 239 |
Add to Cart
|
2 days
|
Rule for rounding off of numberical values and judgement of testing values for technical standards of metallurgy
| Obsolete |
Standards related to (historical): YB/T 081-2013
PDF Preview
YB/T 081-2013: PDF in English (YBT 081-2013) YB/T 081-2013
YB
BLACK METALLURGICAL INDUSTRY STANDARD
OF THE PEOPLE’S REPUBLIC OF CHINA
ICS 03.120.30
H 00
Replacing YB/T 081-1996
Rule for rounding off of numerical values and judgment
of testing values for technical standards of metallurgy
ISSUED ON. APRIL 25, 2013
IMPLEMENTED ON. SEPTEMBER 1, 2013
Issued by. Ministry of Industry and Information Technology of the
People's Republic of China
3. No action is required - Full-copy of this standard will be automatically &
immediately delivered to your EMAIL address in 0~60 minutes.
Table of Contents
Foreword ... 3
1 Scope .. 4
2 Normative references ... 4
3 Terms and definitions ... 4
4. Rounding-off rules of testing values or its calculated values in technical
standards of metallurgy ... 4
5 The comparison method between testing values or its calculated values and
numerical value limit specified by the standard .. 5
6. Rounding-off key points of the testing values or its calculated value of various
performance in technical standards of metallurgy ... 7
7 The coordination and connection requirements of product standards and test
method standards for the rounding interval of index or parameter values ... 8
Foreword
This standard is drafted according to the rules given in GB/T 1.1 2009.
This standard replaces YB/T 081 1996 "Rule for rounding off of numerical
values and judgment of testing values for technical standards of metallurgy".
As compared with YB/T 081 1996, the main technical changes are as follows.
-- Add "terms and definitions" (see Chapter 3);
-- Delete the relevant requirements of carrying out numerical values
rounding-off department (see 1996 version 3.14 and 3.1.5);
-- Modify the compiling format of judgment method of numerical values (see
Chapter 5, 1996 version 3.2);
-- Modify the coordination and connection requirements of product standards
and test method standards for the rounding interval of index or parameter
values (see Chapter 7, 1996 version Chapter 5).
This standard was proposed by China Iron and Steel Association.
This standard shall be under the jurisdiction of National Steel Standardization
Technical Committee (SAC/TC 183).
The drafting organization of this standard. Metallurgical Industry Information
Standards Institute.
The main drafters of this standard. Yi Yan, Dai Qiang, Hou Jie.
This standard was first released in May 1996.
Rule for rounding off of numerical values and judgment
of testing values for technical standards of metallurgy
1 Scope
This standard specifies the principle and the rounding-off key points of carrying
out rounding off of numerical values and judgment of testing values or its
calculated values in metallurgical standardization activities, and the
coordination and connection requirements of product standards and test
method standards for the rounding interval of index or parameter values.
This standard applies to the compiling of all kinds of technical standards of
metallurgy or relevant documents and the judgment of testing values or its
calculated values.
2 Normative references
The following documents are essential for the application of this document. For
dated references, only the dated version applies to this document. For undated
references, the latest version (including all amendments) applies to this
document.
GB/T 228.1-2010 Metallic materials - Tensile testing - Part 1. Method of test
at room temperature
GB/T 8170-2008 Rules of rounding off for numerical values & expression and
judgment of limiting values
3 Terms and definitions
Terms and definitions defined in GB/T 8170-2008 apply to this document.
4. Rounding-off rules of testing values or its calculated
values in technical standards of metallurgy
4.1 In the activities of revising and implementing technical standards of
metallurgy or related documents, determine a variety of indexes and
parameters; for the testing values or its calculated values, when rounding off is
5.4 Comparison of two judgment methods
Examples of the comparison results are shown in Table 1, which compare the
testing values or its calculated values with the specified numerical value limit in
different situations using full numerical comparison method and rounding-off
value comparison method. For the same numerical value limit, if it is satisfactory
in itself, full numerical comparison method is relatively stricter than rounding-off
value comparison method.
6. Rounding-off key points of the testing values or its
calculated value of various performance in technical
standards of metallurgy
6.1 Chemical Analysis
The measured values of elements obtained through chemical analysis shall be
rounded off so that the numerical digit identified by numerical value shall be in
accordance with the numerical digit identified by chemical composition
numerical value specified in the corresponding product standards or relevant
documents.
6.2 Mechanical Property
6.2.1 If the standard or relevant documents do not specify the rounding interval,
the tensile test results of metal materials shall be rounded off according to the
provisions of Table 2.
6.2.2 If the standard or relevant documents do not specify the rounding interval,
the impact test values of metal materials shall be rounded off according to the
following requirements.
a) When impact absorbed energy is no less than 10 J, round off to 1J;
b) When impact absorbed energy is less than 10 J, round off to 0.5 J.
6.2.3 If the standard or relevant documents do not specify the rounding interval,
the mechanical property values of refractory and carbon materials shall be
rounded off according to the following requirements.
a) When bending and compressive strength is no greater than 100 MPa,
round off to 0.1 MPa;
b) When bending and compressive strength is greater than 100 MPa, round
off to 1 MPa.
......
Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.
|