JB/T 6688-1993 PDF English
Search result: JB/T 6688-1993_English: PDF (JB/T6688-1993)
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Name of Chinese Standard | Status |
| JB/T 6688-1993 | English | 70 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Specification for 12-spline Flange Nut and 12 point Flange Nut
| Obsolete |
BUY with any currencies (Euro, JPY, GBP, KRW etc.): JB/T 6688-1993 Related standards: JB/T 6688-1993
PDF Preview: JB/T 6688-1993
JB/T 6688-1993: PDF in English (JBT 6688-1993) JB/T 6688-1993
JB
INDUSTRY STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
J 13
Specification for 12-spline Flange Nut and 12
point Flange Nut
ISSUED ON. JUNE 01, 1993
IMPLEMENTED ON. JANUARY 01, 1994
Issued by. Ministry of Machinery Industry of PRC
Table of Contents
1 Scope ... 3
2 Normative references ... 3
3 Technical conditions ... 3
4 Inspection rules ... 8
5 Acceptance inspection, marking and packaging ... 9
Additional Information... 9
Specification for 12-spline Flange Nut and 12 point
Flange Nut
1 Scope
This Standard applies to the manufacture and acceptance of 12-spline flange nut and
12 point flange nut (hereinafter referred to as bolt and nut respectively) that are used for
gas turbine power plant.
2 Normative references
GB 3 Run-outs, undercuts and chamfers for general purpose metric screw
threads
GB 196 General purpose screw threads - Basic dimensions for diameter from 1
to 600mm
GB 197 General purpose screw threads - Tolerances and fits for diameter from 1
to 355mm
GB 228 Tensile testing of metallic materials
GB 3077 Technical requirements for alloy structure steels
GB 3098.1~3098.4 Mechanical properties of fasteners
GB 3099 Bolts, screws, nuts and accessories - terminology and nomenclature
GB 3106 Bolts, screws and studs - Nominal lengths and thread lengths for
general purpose bolts
GB 5276 Fasteners - Bolts, screws, studs and nuts - Symbols and designations
of dimensions
GBn 177 Hot-rolled and forged heat-resisting super alloy bars for general
force-bearing parts
3 Technical conditions
3.1 Main indicators
3.1.3.1 Tolerance of screw thread
a. Tolerance of outer screw thread is 6g;
b. Tolerance of inner screw thread is 6H.
3.1.3.2 The biggest permissible value of surface roughness parameter for screw
thread side Ra is 3.2µm.
3.1.4 When the material yield limit is not less than 932MPa, the wrenching force that
the bolt can withstand shall not be less than the provisions in Table 5.
Table 5
Thread specification
mm M6 M8 M10 M12 M14 M16 M18 M20 M22 M24
Wrenching force
N●m 8.14 18.1 29.9 58.3 93.5 127.1 183.3 223.5 331.8 485.6
Thread specification
mm M27 M0 M33 M36 M39 M42 M45 M48 M52
Wrenching force
N●m 543.0 880.8 1153 1564 1926 2407 2926 3845 3845
3.1.5 When the material yield limit is not less than 932MPa, the wrenching force that
the bolt can withstand shall not be less than the provisions in Table 6.
Table 6
Thread specification
mm M6 M8 M10 M12 M16 M20 M24
Wrenching force
N●m 9.75 21.7 32.5 68.7 165.0 326.1 540.1
Thread specification
mm M27 M30×3 M33×3 M36×3 M39×3 M42×3 M45×3
Wrenching force
N●m 777.5 1273 1593 2045 2544 3200 4076
3.1.6 Geometric tolerances of bolts and nuts shall be in accordance with the
provisions in Table 7-1 ~ Table 7-3.
3.1.6.1 Coaxiality
4.7 Wrenching torque test of bolts. When torque reaches to the values in Table 5,
12-spline of bolts shall not produce the permanent deformation that influences the
usage and sliding between wrenches. Accuracy of torque measuring device shall not
be less than ±5%.
4.8 Wrenching torque test of nuts. When torque reaches to the values in Table 5, 12
point of nuts shall not produce the permanent deformation that influences the usage
and sliding between wrenches. Accuracy of torque measuring device shall not be less
than ±5%.
5 Acceptance inspection, marking and packaging
5.1 Bolts and nuts shall be submitted for inspection in batch. Each batch shall be
made of materials with same type, same size and same furnace number. It shall
conduct heat treatment according to the same specification.
5.2 Appearance of bolts and nuts shall be subject to 100% inspection.
5.3 As required, bolts and nuts can be subject to magnetic particle inspection or
fluorescence detection.
5.4 Bolts shall be marked at the head-top by braille or concave characters. Nuts shall
be marked at the supporting surface by concave characters. Marking symbol.
30CrMnSi and 40CrNiMoA use symbol “D”; 40Cr2MoV use symbol “Z”; GH2132 use
symbol “G”.
5.5 Other acceptance rules and packaging shall be in accordance with GB 90
“Acceptance inspection, marking and packaging of fasteners”.
Additional Information.
The Standard was proposed by Nanjing Institute of Gas Turbine.
This Standard shall be under the jurisdiction of Nanjing Institute of Gas Turbine.
This standard is drafted by the following organizations. Nanjing Turbine & Electric
Machinery (Group) Co., Ltd., Nanjing Institute of Gas Turbine, Harbin Steam Turbine
Plant, and China Shipbuilding Industry Corporation 703 Research Institute.
......
Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.
|