GB/T 38712-2020 PDF English
US$125.00 · In stock · Download in 9 secondsGB/T 38712-2020: Test method for thermal conductivity of ultrathin glass - Heat flow method Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 38712-2020 | English | 125 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Test method for thermal conductivity of ultrathin glass - Heat flow method
| Valid |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 38712-2020
GB/T 38712-2020: Test method for thermal conductivity of ultrathin glass - Heat flow method---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT38712-2020
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 81.040.01
Q 34
Test method for thermal conductivity of ultrathin glass
- Heat flow method
ISSUED ON: MARCH 31, 2020
IMPLEMENTED ON: FEBRUARY 01, 2021
Issued by: State Administration for Market Regulation;
Standardization Administration of the People’s Republic of
China.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Terms and definitions ... 4
4 Test device ... 5
5 Environmental conditions ... 6
6 Sample requirements ... 6
7 Test steps ... 7
8 Result calculation and expression ... 8
9 Instrument calibration ... 9
10 Test report ... 9
Test method for thermal conductivity of ultrathin glass
- Heat flow method
1 Scope
This Standard specifies the terms and definitions, test device, environmental
conditions, sample requirements, test steps, result calculation and expression,
instrument calibration, and test reports for measuring the thermal conductivity
of ultrathin glass by the heat flow method.
This Standard applies to the test of the thermal conductivity of ultrathin glass.
2 Normative references
The following documents are indispensable for the application of this document.
For dated references, only the dated version applies to this document. For
undated references, the latest edition (including all amendments) applies to this
document.
GB/T 5598, Test method for thermal conductivity of beryllium oxide ceramics
GB/T 21389, Vernier, dial and digital display calipers
GB/T 34171, Test method for flexural property of thin and ultrathin glass -
Three-point bending method
3 Terms and definitions
Terms and definitions determined by GB/T 5598, GB/T 34171 and the following
ones are applicable to this document.
3.1 Ultrathin glass
Plate glass products whose thickness is not greater than 1.1 mm.
3.2 Thermal conductivity
On the unit area, the steady-state heat flow rate that is caused by the unit
temperature gradient perpendicular to this direction. Under steady-state heat
conduction conditions, the density of heat flow is divided by the temperature
gradient.
3.3 Heat flow method
Place the sample between the cold pole and the hot pole. The temperature
difference causes heat to pass through the sample. According to the known
material thickness, thermal conductivity, temperature difference between the
two ends and the area of the end face, obtain a one-dimensional steady-state
heat flow, thereby calculate the thermal conductivity of the sample.
4 Test device
The test device mainly consists of heating source, cold pole, hot pole,
pressurization system, cooling system, thermocouple, as shown in Figure 1; the
specific requirements of the test device are as follows:
a) The heater is made of a metal material of a large thermal conductivity
(brass is recommended); it adopts an internal heating structure; the
temperature is controlled by a digital display temperature-controlled meter,
to provide a stable heat source for the hot pole; the temperature deviation
is less than 0.2 °C;
b) The cold pole and the hot pole shall be materials of the same diameter
and have a thermal conductivity greater than 50 W/(m·K); the diameter
shall be preferably 30 mm ~ 40 mm; the surface shall be flat and smooth;
c) The pressurization system is mainly composed of a pressure sensor and
a motor, which pressurizes the sample; the pressing force is adjustable at
0 N ~ 1000 N;
d) The cooling system includes a constant temperature water tank and a
cooler. The cooler is made of brass, and is equipped with a water tank
inside, which is connected to the outer constant temperature water tank
through a pipe. Use the water circulation of the external constant
temperature water tank and the cooler to provide a stable temperature for
the cold pole; the temperature deviation is less than 0.2 °C;
e) The thermocouple shall be a thermocouple whose division value is 0.1.
Place two thermocouples on the cold pole and the hot pole, respectively.
The temperature deviation of the same pole shall not exceed 0.2 °C. The
cold end shall be placed in the ice-water mixture (0 °C) for temperature
compensation.
b) Use a Vernier caliper that meets the requirements of GB/T 21389 to
measure the thickness of the glass pieces; calculate the number of glass
pieces whose stack thickness is greater than 2 mm;
c) Wash and dry the small glass pieces; ensure that the surface is clean;
d) Use thermal silicone grease whose thermal conductivity is greater than
1.5 W/(m·K); bond and overlay the cleaned glass pieces; the thermal
silicon grease between the glass pieces shall be applied evenly;
e) Use a pressure that is not less than 200 N to compact the superimposed
samples; then, wipe off the thermal silicone grease that overflows the
edge of the sample;
f) Use a Vernier caliper that meets the requirements of GB/T 21389 to
measure the thickness of the compacted sample; measure it three times
at 120° rotation; take the average value, and record it as d. It is required
that the thickness of the thermal silicon grease between the glass
laminations is not more than 20% of the thickness d of the sample.
6.2 Number of samples
The number of samples is 3.
7 Test steps
7.1 Test preparation
The test preparation steps are as follows:
a) Insert the cold ends of all thermocouples into the ice-water mixture (0 °C)
to compensate for the cold end temperature;
b) Set the cold pole temperature to (20 ± 5) °C;
c) Set the hot pole temperature; the hot pole temperature shall be 40 °C
greater than the cold pole temperature.
7.2 Sample placement
Apply thermal silicon grease whose thermal conductivity is not less than 1.5
W/(m·K) on the upper and lower sides of the sample; the total thickness of the
thermal silicon grease on the upper and lower sides of the sample is not more
than 0.1 mm; then, place it between the cold and hot poles.
7.3 Sample test
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 38712-2020 be delivered?Answer: The full copy PDF of English version of GB/T 38712-2020 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 38712-2020_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 38712-2020_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 38712-2020 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. How to buy and download a true PDF of English version of GB/T 38712-2020?A step-by-step guide to download PDF of GB/T 38712-2020_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 38712-2020".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|