GB/T 37785-2019 PDF in English
GB/T 37785-2019 (GB/T37785-2019, GBT 37785-2019, GBT37785-2019)
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Name of Chinese Standard | Status |
| GB/T 37785-2019 | English | 110 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Flue gas desulfurization gypsum
| Valid |
Standards related to (historical): GB/T 37785-2019
PDF Preview
GB/T 37785-2019: PDF in English (GBT 37785-2019) GB/T 37785-2019
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 91.100.10
Q 62
Flue gas desulfurization gypsum
烟气脱硫石膏
ISSUED ON: AUGUST 30, 2019
IMPLEMENTED ON: JULY 01, 2020
Issued by: State Administration for Market Regulation;
Standardization Administration of the People's Republic of China.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Grading and marking ... 4
4 Technical requirements ... 4
5 Test method ... 5
6 Inspection rules ... 7
7 Packaging, labeling, transportation and storage ... 8
Flue gas desulfurization gypsum
1 Scope
This standard specifies the classification and labeling, technical requirements, test
methods, inspection rules and packaging, marking, and transportation and storage of
flue gas desulfurization gypsum.
This standard applies to flue gas desulfurization gypsum that adopts limestone/lime -
gypsum wet method to desulfurize and purify sulfur-containing flue gas, so as to
produce the main component of calcium sulfate dihydrate (CaSO4•2H2O).
2 Normative references
The following documents are indispensable for the application of this document. For
dated references, only the dated version applies to this document. For undated
references, the latest version (including all amendments) applies to this document.
GB/T 176 Methods for chemical analysis of cement
GB/T 2007.1 General rules for the sampling and sample preparation of minerals in
bulk - Sampling by manual method
GB/T 5484 Methods for chemical analysis of gypsum
3 Grading and marking
3.1 Grading
Products are mainly divided into three grades: Grade 1, Grade 2, and Grade 3 according
to the content of calcium sulfate dihydrate.
3.2 Marking
It shall be marked in the order of product name, grade and standard number.
Example: For Grade 1 flue gas desulfurization gypsum, it is marked as follows:
Flue gas desulfurization gypsum Grade 1 GB/T 37785-2019
4 Technical requirements
The technical requirements for flue gas desulfurization gypsum shall meet the
Where,
w(CaSO4•2H2O) – Content of calcium sulfate dihydrate (mass fraction), %;
wc – Content of crystal water (mass fraction), %;
20.9275 -- The conversion factor of crystal water content to calcium sulfate
dihydrate content.
The calculation result is accurate to 0.01%.
5.4 Chloride ion (Cl-)
Measured according to the method specified in GB/T 176. The calculated results are
expressed in milligrams per kilogram (mg/kg).
The calculation result is accurate to 1 mg/kg.
5.5 Calcium sulfite hemihydrate (CaSO3•1/2H2O)
Determine the sulfur dioxide content (mass fraction) w(SO2) according to the method
specified in GB/T 5484. Calcium sulfite hemihydrate content (mass fraction) by
Formula (2) calculation:
Where,
w(CaSO3•1/2H2O) – Content of calcium sulfite hemihydrate (mass fraction), %;
w(SO2) – Content of sulfur dioxide (mass fraction), %;
2.016 -- The conversion factor of sulfur dioxide content to calcium sulfite
hemihydrate content.
The calculation result is accurate to 0.01%.
5.6 Water-soluble magnesium oxide (MgO)
Measure according to the method specified in GB/T 5484.
The calculation result is accurate to 0.01%.
5.7 Water-soluble sodium oxide (Na2O)
Measure according to the method specified in GB/T 5484.
The calculation result is accurate to 0.01%.
5.8 pH value
Measure according to the method specified in GB/T 5484.
The result is accurate to 0.1.
6 Inspection rules
6.1 Inspection classification
6.1.1 Exit-factory inspection
The exit-factory inspection items are: attached water content, calcium sulfate dihydrate
(CaSO4•2H2O), and chloride ion (Cl-).
6.1.2 Type inspection
The type inspection items are all the technical requirements stipulated in Chapter 4.
In one of the following situations, the type inspection of the product shall be carried
out:
a) When there are major changes in raw materials, processes or equipment;
b) When the production-line is discontinued for more than half a year and then the
production is resumed;
c) Once a year during normal production.
6.2 Batching and sampling
6.2.1 Batching
For a manufacturing organization with an annual output of flue gas desulfurization
gypsum less than 50,000 tons, no more than 150 tons is deemed as a batch; for a
manufacturing organization with an annual output of 50,000 tons ~ 100,000 tons, no
more than 300 tons is deemed as a batch; for a manufacturing organization with an
annual output of 100,000 tons ~ 200,000 tons, no more than 500 tons is deemed as a
batch; for a manufacturing organization with an annual output of more than 200,000
tons, no more than 800 tons is deemed as a batch. Each batch is deemed as a serial
number; if there is less than one batch, it is deemed as a batch.
6.2.2 Sampling
Sampling shall be carried out according to the method specified in GB/T 2007.1; the
total sampling amount of each batch shall not be less than 2kg. Divide the sample into
......
Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.
|