GB/T 23275-2009 PDF in English
GB/T 23275-2009 (GB/T23275-2009, GBT 23275-2009, GBT23275-2009)
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Name of Chinese Standard | Status |
| GB/T 23275-2009 | English | 110 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Methods for chemical analysis of ruthenium determination of lead, iron, nickel, aluminum, copper, silver, gold, platinum, palladium, rhodium, iridium and silicon in ruthenium powder by glow discharge mass spectrometry
| Valid |
Standards related to: GB/T 23275-2009
PDF Preview
GB/T 23275-2009: PDF in English (GBT 23275-2009) GB/T 23275-2009
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 77.040.30
H 15
Methods for chemical analysis of ruthenium determination
of lead, iron, nickel, aluminum, copper, silver, gold,
platinum, palladium, rhodium, iridium and silicon in
ruthenium powder by glow discharge mass spectrometry
ISSUED ON: JANUARY 05, 2009
IMPLEMENTED ON: NOVEMBER 01, 2009
Issued by: General Administration of Quality Supervision, Inspection and
Quarantine;
Standardization Administration of the People’s Republic of China.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Method summary ... 4
3 Reagents and materials ... 5
4 Instruments ... 5
5 Sample preparation ... 5
6 Analysis steps ... 5
7 Calculation and expression of analysis results ... 6
8 Tolerance ... 6
9 Quality assurance and control ... 6
Appendix A (Informative) Glow discharge mass spectrometer ELEMENT GD working
parameters ... 7
Methods for chemical analysis of ruthenium determination
of lead, iron, nickel, aluminum, copper, silver, gold,
platinum, palladium, rhodium, iridium and silicon in
ruthenium powder by glow discharge mass spectrometry
1 Scope
This Standard specifies the method for the determination of lead, iron, nickel, aluminum,
copper, silver, gold, platinum, palladium, rhodium, iridium and silicon in ruthenium
powder.
This Standard applies to the determination of lead, iron, nickel, aluminum, copper,
silver, gold, platinum, palladium, rhodium, iridium and silicon in ruthenium powder, of
which the determination ranges are shown in Table 1.
2 Method summary
Prepare the sample by powder-pressing method. Use the sample as the cathode of the
glow discharge power supply. The atoms of the sample (cathode) are peeled off from
the sample under the impact of argon ions (cathode sputtering), enter the plasma, and
become positive ions by electron collision and Penning collision. Positive ions are
accelerated through the outlet of the ion source and then enter the mass spectrometer,
which analyzes according to the charge-to-mass ratio and ion intensity.
3 Reagents and materials
3.1 Absolute ethanol (analytical reagent).
3.2 Pure argon.
3.3 High-purity argon.
4 Instruments
4.1 Pressing machine, whose rated pressure is not less than 15 MPa.
4.2 Glow discharge mass spectrometer, whose working parameters are shown in
Appendix A
In order to ensure the working state of the instrument, the following conditions must be
met:
-- The high vacuum of the instrument analyzer must be less than 5×10-7 mbar, and
the fore vacuum must be less than 1×10-3 mbar.
-- The heat transfer between the sample and the sample holder must be good, and the
cooling temperature shall be set at 15 °C.
-- The instrument shall be in a state of good mass calibration and Faraday detector
calibration before testing.
-- Discharge parameters, gas pressure and lens voltage, etc. can be adjusted to obtain
good peak shape, resolution and 102Ru matrix signal of not less than 5 × 107 cps.
5 Sample preparation
Use absolute ethanol (3.1) to wash and air-dry the part in contact with the sample in the
steel ring of the tablet-producing mold of the pressing machine in advance; then, weigh
5 g ~ 10 g of the sample and place it in the steel ring of the tablet-producing mold; start
the pressing machine, and press at a pressure of 15 MPa for at least 3 min; take out the
tablet.
6 Analysis steps
Load the sample into the sample holder on the glow discharge mass spectrometer; adopt
an appropriate instrument working condition, to carry out sample pre-sputtering first;
perform sample analysis after the signal of the element to be measured is stabilized.
......
Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.
|