GB/T 13881-2019 PDF in English
GB/T 13881-2019 (GB/T13881-2019, GBT 13881-2019, GBT13881-2019)
Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Name of Chinese Standard | Status |
GB/T 13881-2019 | English | 150 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Road vehicles -- Pneumatic braking connections between towing vehicles and trailers
| Valid |
GB/T 13881-1992 | English | 279 |
Add to Cart
|
3 days
|
Pneumatic braking connections between motor vehicles and towed vehicles
| Obsolete |
Standards related to (historical): GB/T 13881-2019
PDF Preview
GB/T 13881-2019: PDF in English (GBT 13881-2019) GB/T 13881-2019
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 43.040.40
T 74
Replacing GB/T 13881-1992
Road Vehicles - Pneumatic Braking Connections
between Towing Vehicles and Trailers
(ISO 1728:2006, Road Vehicles - Pneumatic Braking Connections
between Motor Vehicles and Towed Vehicles - Interchangeability, NEQ)
ISSUED ON: OCTOBER 18, 2019
IMPLEMENTED ON: MAY 1, 2020
Issued by: State Administration for Market Regulation;
Standardization Administration of the People’s Republic of
China.
Table of Contents
Foreword ... 3
1 Scope ... 5
2 Normative References ... 5
3 Type and Interchangeability Dimensions ... 5
4 Performance Requirements ... 8
5 Test Methods ... 10
6 Installation, Usage and Marking ... 12
Foreword
This Standard was drafted in accordance with the rules in GB/T 1.1-2009.
This Standard serves as a replacement of GB/T 13881-1992 Braking Connections
between Motor Vehicles and Towed Vehicles. In comparison with GB/T 13881-1992,
except from editorial modifications, the main technical changes are as follows:
---Normative references are added (see Chapter 2);
---Performance requirements are added (see Chapter 4);
---Test methods are added (see Chapter 5);
---The requirements for installation location and jumper hose length are modified;
the specific requirements are modified into reference to GB/T 32861 (see 6.1;
3.1 ~ 3.6 in Version 1992);
---The requirements for the numerical value of A and B in connector
interchangeability dimension table are modified (see Table 1 in 3.5; 2.6 in
Version 1992);
---The requirements for connector colors are modified; the requirements for jumper
hose colors are deleted (see 6.3; 3.7 in Version 1992);
The formulation of this Standard adopts the re-drafting law and takes ISO 1728:2006
Road Vehicles - Pneumatic Braking Connections between Motor Vehicles and Towed
Vehicles - Interchangeability as a reference. The degree of consistency with ISO
1728:2006 is non-equivalent.
This Standard was proposed by Ministry of Industry and Information Technology of
People’s Republic of China.
This Standard shall be under the jurisdiction of National Technical Committee 114 on
Road Vehicles of Standardization Administration of China (SAC/TC 114).
The drafting organizations of this Standard: Research Institute of Highway Ministry of
Transport; Beijing Foton Daimler Automotive Co., Ltd.; RUILI Group RUIAN
Automotive Parts Co., Ltd.; WABCO Vehicle Control Systems Co., Ltd.; Beijing HUATE
Auto Parts Co., Ltd.
The main drafters of this Standard: Zhang Hongwei, Zhang Hongsong, Li Chuanwu,
Zhang Xueli, Guo Junting, Dong Jinsong, Huang Chengyuan, Men Yupeng, Zong
Chengqiang, Shi Haiyan, Zhanghai, Yao Xinyan, Qu Chuanjin, Zhang Guolong, Huang
Chaozhi, Zhang Changlu.
The issuing of the previous versions of the standard replaced by this Standard is as
Road Vehicles - Pneumatic Braking Connections
between Towing Vehicles and Trailers
1 Scope
This Standard stipulates the type, interchangeability dimensions, performance
requirements, test methods, installation, usage and marking of pneumatic braking
connections between towing vehicles and trailers.
This Standard is applicable to pneumatic braking connectors adopted in double-
pipeline pneumatic braking system equipped in automobiles and trains. Specifically
speaking, one of the pipelines is power supply pipeline, and the other is control pipeline.
2 Normative References
The following documents are indispensable to the application of this document. In
terms of references with a specified date, only versions with a specified date are
applicable to this document. In terms of references without a specified date, the latest
version (including all the modifications) is applicable to this document.
GB/T 10125 Corrosion Tests in Artificial Atmospheres - Salt Spray Tests;
GB/T 32861 Road Vehicles - Location of Electrical and Pneumatic Connections
between Towing Vehicles and Trailers
3 Type and Interchangeability Dimensions
3.1 Pneumatic braking connector is connected by fixed joint and movable joint (see
Figure 1).
After air-tightness test, connector’s pressure drop shall not be more than 10 kPa.
4.3 Corrosion Resistance
After corrosion resistance test, respectively test the torque of connection and
disconnection, and air-tightness in accordance with 5.1 and 5.2. A normally functioning
connector shall satisfy the requirements of the torque of connection and disconnection
in 4.1 and the requirements of air-tightness in 4.2.
4.4 Durability
After durability test, in accordance with 5.1 and 5.2, respectively test the torque of
connection and disconnection, and air-tightness. A normally functioning connector
shall satisfy the requirements of the torque of connection and disconnection in 4.1 and
the requirements of air-tightness in 4.2.
4.5 Pull-off Resistance
When connector is pulled off, the tensile force shall be 220 N ~ 1,334 N.
After pull-off test, in accordance with 5.1 and 5.2, respectively test the torque of
connection and disconnection, and air-tightness. A normally functioning connector
shall satisfy the requirements of the torque of connection and disconnection in 4.1 and
the requirements of air-tightness in 4.2.
4.6 Dropping Resistance
After drop test, in accordance with 5.1 and 5.2, respectively test the torque of
connection and disconnection, and air-tightness. A normally functioning connector
shall satisfy the requirements of the torque of connection and disconnection in 4.1 and
the requirements of air-tightness in 4.2.
4.7 High Temperature
After high temperature test, under the stipulated temperature conditions, in accordance
with 5.1 and 5.2, respectively test the torque of connection and disconnection, and air-
tightness. A normally functioning connector shall satisfy the requirements of the torque
of connection and disconnection in 4.1 and the requirements of air-tightness in 4.2.
4.8 Low Temperature
After low temperature test, under the stipulated temperature conditions, in accordance
with 5.1 and 5.2, respectively test the torque of connection and disconnection, and air-
tightness. A normally functioning and disconnected connector shall satisfy the
requirements of the torque of connection and disconnection in 4.1 and the
requirements of air-tightness in 4.2; a normally functioning and connected connector
shall satisfy the requirements of air-tightness in 4.2.
2---movable joint;
M---pressure meter;
C---1 L air cylinder;
A---control valve;
FR---pressure regulating valve.
Figure 4 -- Principle of Air-tightness Test of Pneumatic Braking Connector
5.3 Corrosion Resistance Test
In accordance with GB/T 10125, conduct 240 h corrosion resistance test on two pairs
of new connectors (one pair is correctly connected, with the threaded port blocked; the
other pair is disconnected). After the test, in accordance with 5.1 and 5.2, respectively
test the torque of connection and disconnection, and air-tightness.
5.4 Durability Test
In accordance with the requirements, conduct the operation of connection and
disconnection on one pair of new connectors. At the rate of 15 ~ 25 cycles in each
minute, complete 2,500 cycles. A complete cyclic process shall include one connection
and one disconnection. After the test, in accordance with 5.1 and 5.2, respectively test
the torque of connection and disconnection, and air-tightness.
5.5 Pull-off Resistance Test
In accordance with the requirements, connect one pair of new connectors. Meanwhile,
connect the air supply pipeline and raise pressure to 850 kPa ± 30 kPa. Then, apply
tensile force onto the connector along the direction of the center line of the braking
pipeline. The tensile force shall gradually increase from 0, till the connector is
disconnected. After the test, in accordance with 5.1 and 5.2, respectively test the
torque of connection and disconnection, and air-tightness.
5.6 Dropping Resistance Test
Respectively from the height of at least 1.8 m, randomly drop the two joints of the
connector onto concrete surface, for at least once. After the test, in accordance with
5.1 and 5.2, respectively test the torque of connection and disconnection, and air-
tightness.
5.7 High Temperature Test
Expose two pairs of new connectors (one pair is correctly connected; the other pair is
disconnected) at the temperature of 80 °C ± 3 °C for at least 24 h. Then, at this
temperature, in accordance with 5.1 and 5.2, respectively test the torque of connection
...... Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.
|