GB/T 1510-2016 PDF English
US$170.00 · In stock · Download in 9 secondsGB/T 1510-2016: Manganese ores - Determination of aluminium content - EDTA titrimetric method Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid GB/T 1510: Evolution and historical versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 1510-2016 | English | 170 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Manganese ores - Determination of aluminium content - EDTA titrimetric method
| Valid |
| GB/T 1510-2006 | English | 279 |
Add to Cart
|
3 days
|
Manganese ores -- Determination of aluminium content -- EDTA titrimetric method
| Obsolete |
| GB/T 1510-1979 | English | 199 |
Add to Cart
|
2 days
|
Method for determination of aluminium trioxide content in manganese ores
| Obsolete |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 1510-2016
GB/T 1510-2016: Manganese ores - Determination of aluminium content - EDTA titrimetric method---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT1510-2016
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 73.060.20
D 32
Replacing GB/T 1510-2006
Manganese ores - Determination of aluminium content
- EDTA titrimetric method
ISSUED ON: AUGUST 29, 2016
IMPLEMENTED ON: JULY 01, 2017
Issued by: General Administration of Quality Supervision, Inspection
and Quarantine;
Standardization Administration of the People’s Republic of
China.
Table of Contents
Foreword ... 3
1 Scope ... 5
2 Normative references ... 5
3 Principle ... 5
4 Reagents and materials ... 6
5 Instruments ... 8
6 Sampling ... 8
7 Analysis steps ... 8
8 Calculation of analysis results ... 10
9 Test report ... 13
Appendix A (Normative) Sample analysis value acceptance procedure flow
chart ... 14
Manganese ores - Determination of aluminium content
- EDTA titrimetric method
WARNING – The personnel who uses this Standard shall have hands-on
experience in formal laboratory work. This Standard does not address all
possible security issues. It is the responsibility of the user to take
appropriate safety and health measures and to ensure compliance with
the conditions which are set by the relevant national regulations.
1 Scope
This Standard specifies the determination of aluminium content in manganese
ores by EDTA titrimetric method.
This Standard applies to the determination of aluminium content in manganese
ores and manganese concentrates; the determination range (mass fraction):
0.10% ~ 12.50%.
2 Normative references
The following referenced documents are indispensable for the application of
this document. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any
amendments) applies.
GB/T 2011, Method of sampling and sample preparation of manganese ores
in bulk
GB/T 6682, Water for analytical laboratory use - Specification and test
methods
GB/T 8170, Rules of rounding off for numerical values & expression and
judgment of limiting values
GB/T 14949.8, Manganese ores - Determination of hygroscopic moisture
content - Gravimetric method
3 Principle
For the sample, use hydrochloric acid-nitric acid to decompose, and use sulfuric
acid-hydrofluoric acid to evaporates silicon. After precipitation and separation
by hexamethylenetetramine, use hydrochloric acid to dissolve the aluminium
hydroxide precipitate; use sodium carbonate-boric acid to melt the residue.
After separation by strong base, divide the filtrate into the slightly acidic solution;
then, add excess EDTA. When the pH value is 5 ~ 5.5, use xylenol orange as
indicator; use zinc standard titration solution to titrate excess EDTA; use fluoride
ion to replace the EDTA with aluminium; then, use zinc standard titration
solution to titrate. According to the consumption of zinc standard titration
solution, calculate the aluminium content.
4 Reagents and materials
In the analysis process, only use approved analytical reagents and water of
grade 3 and above in accordance with GB/T 6682.
4.1 Mixed solvent: the mass ratio of sodium carbonate and boric acid is 2:1;
grind and mix well.
4.2 Nitric acid, ρ = 1.42 g/mL.
4.3 Hydrochloric acid, ρ = 1.19 g/mL.
4.4 Hydrochloric acid, 1+1.
4.5 Hydrochloric acid, 1+2.
4.6 Hydrochloric acid, 1+5.
4.7 Hydrochloric acid, 2+98.
4.8 Sulfuric acid: 1+1.
4.9 Hydrofluoric acid, ρ = 1.17 g/mL.
4.10 Hydrogen peroxide, mass fraction of 30%.
4.11 Ammonia water, 1+1.
4.12 Hydrochloric acid-hexamethylenetetramine solution (pH = 5 ~ 5.5): Weigh
40 g of hexamethylenetetramine and dissolve it in water; add 20 mL of
hydrochloric acid (1+1); use water to dilute to 100 mL; mix well.
4.13 Hexamethylenetetramine solution, 5 g/L.
4.14 Sodium hydroxide solution, 500 g/L: Weigh 500 g of sodium hydroxide;
use water to dissolve and dilute to 1 L; store in a plastic bottle.
4.15 Sodium fluoride saturated solution: Store in a plastic bottle.
7.4 Determination
7.4.1 Preparation of sample solutions
7.4.1.1 Put the sample (see 7.2) in a 400 mL beaker; add 20 mL of hydrochloric
acid (see 4.3); heat the solution until there is no obvious reaction,; then, add 5
mL of nitric acid (see 4.2). Continue to heat to dissolve until nearly dry; remove
and cool slightly; add 20 mL of hydrochloric acid (see 4.4) and 100 mL of water;
heat to dissolve the salts. Remove it; use medium-speed filter paper to filter
while it is still hot; use hot water to wash the filter paper 10 ~ 15 times. Keep
the filtrate as main liquid A.
7.4.1.2 Transfer the filter paper and residue into a platinum dish or platinum
crucible; dry and carbonize at low temperature; put it into a high temperature
furnace at about 550 °C for ashing; then, burn it in a high temperature furnace
at 850 °C for 10 minutes; remove it for cooling. Add 2 mL of sulfuric acid (see
4.8); add 3 mL ~ 5 mL of hydrofluoric acid (see 4.9) dropwise; after heating to
evaporate the silicon, heat it on an electric hot plate until the sulfuric acid emits
smoke; remove it. Slightly cool; blow a small amount of water around the
platinum dish; then, heat until the sulfuric acid smokes and is almost dry.
Remove it; add 10 mL of hydrochloric acid (see 4.4); heat to dissolve the salts;
combine the test solution with the main solution A.
7.4.2 Separation of hexamethylenetetramine
7.4.2.1 Adjust the volume of the solution (see 7.4.1.2) to about 100 mL ~ 150
mL; boil and remove. Use ammonia water (see 4.11) to neutralize until a
precipitation occurs; then, use hydrochloric acid (see 4.4) to adjust until the
precipitate just dissolves; add 5 ~ 10 drops in excess. Add 20 mL of hydrochloric
acid-hexamethylenetetramine solution (see 4.12); heat to slightly boil and keep
at a temperature (80 °C ~ 90 °C) for 15 min ~ 20 min. Remove and cool slightly;
use a medium-speed filter paper to filter (in two funnels when there are a lot of
precipitations of hydroxide of iron and aluminium); use hot
hexamethylenetetramine solution (see 4.13) to wash the beaker and precipitate
5 ~ 8 times respectively. Use 30 mL of hot hydrochloric acid (see 4.5) to dissolve
the precipitate in the original beaker; use hot hydrochloric acid (see 4.7) to wash
the filter paper until it is no longer yellow; then, use hot water to wash the filter
paper for 10 ~ 15 times. Keep the solution as the main liquid B for strong base
separation.
7.4.2.2 Transfer the filter paper and residue into a platinum dish or platinum
crucible; put it into a high temperature furnace at about 550 °C for ashing; then,
burn it in a high temperature furnace at 850 °C for 10 minutes; remove it for
cooling. Add 3 g of mixed solvent (see 4.1); put it in a high temperature furnace
of 950 °C for 10 min; take it out and cool it slightly; add hydrochloric acid (see
4.4) dropwise; heat until the frit is separated from the platinum crucible; pour it
into the main liquid B and combine them.
7.4.3 Strong base separation
Heat and evaporate the solution (see 7.4.2.2) to a volume of about 80 mL ~ 120
mL; add 10 mL of sodium hydroxide solution (see 4.14); use ammonia water
(see 4.11) to neutralize until a precipitation occurs; then, use hydrochloric acid
(see 4.4) to adjust until the precipitate dissolves, and exceed for 10 mL; boil for
1 min ~ 2 min. Remove it and cool it down; add 40 mL of sodium hydroxide
solution (see 4.14) at one time under constant stirring; add 8 ~ 10 drops of
hydrogen peroxide (see 4.10) dropwise; boil for 3 min ~ 5 min. Remove and
cool to room temperature; transfer to a 250 mL volumetric flask; use water to
dilute to the mark; mix well. Use a double-layer medium-speed filter paper for
dry filtration. Discard the initial filtrate.
7.4.4 Acidity adjustment and titration
Pipette the above filtrate (see 7.4.3) accurately according to Table 2 into a 500
mL conical flask; add 2 drops of phenolphthalein indicator solution (see 4.19);
use hydrochloric acid (see 4.4) to adjust it to red; shake while adding; continue
to add hydrochloric acid (see 4.4) until the red color disappears and the solution
is clear (a large amount of hydrochloric acid is used in this process) and exceed
for 5 mL of hydrochloric acid (see 4.6); add EDTA solution (see 4.17) with an
excess of 5 mL ~ 10 mL over the theoretical calculation value (see 4.17); the
pH value of the solution, at this moment, is about 2; then, add 25 mL of
hydrochloric acid-hexamethylenetetramine solution (see 4.12); heat and boil for
3 min ~ 5 min. Remove and cool to room temperature. Add 4 drops of xylenol
orange indicator solution (see 4.20); use zinc standard titration solution (see
4.18.1) to titrate to red as the end point (do not record the consumption of zinc
standard titration solution). Add 25 mL of saturated sodium fluoride solution (see
4.15); boil for 2 min ~ 3 min. Remove it; cool to room temperature; add 1 drop
~ 2 drops of xylenol orange indicator solution (see 4.20); use zinc standard
titration solution (see 4.18.1) to titrate again to red as the end point.
8 Calculation of analysis results
8.1 Calculation of aluminium content
Calculate the aluminium content (mass fraction) in the sample according to
Formula (2); express its value in %.
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 1510-2016 be delivered?Answer: The full copy PDF of English version of GB/T 1510-2016 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 1510-2016_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 1510-2016_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 1510-2016 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. Question 5: Should I purchase the latest version GB/T 1510-2016?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 1510-2016 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. How to buy and download a true PDF of English version of GB/T 1510-2016?A step-by-step guide to download PDF of GB/T 1510-2016_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 1510-2016".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|