|
US$114.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email.
GB/T 21782.5-2010: Coating powders -- Part 5: Determination of flow properties of a powder/air mixture
Status: Valid
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | Status | PDF |
| GB/T 21782.5-2010 | English | 114 |
Add to Cart
|
3 days [Need to translate]
|
Coating powders -- Part 5: Determination of flow properties of a powder/air mixture
| Valid |
GB/T 21782.5-2010
|
PDF similar to GB/T 21782.5-2010
Basic data | Standard ID | GB/T 21782.5-2010 (GB/T21782.5-2010) | | Description (Translated English) | Coating powders -- Part 5: Determination of flow properties of a powder/air mixture | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | G50 | | Classification of International Standard | 87.040 | | Word Count Estimation | 6,694 | | Date of Issue | 2010-09-26 | | Date of Implementation | 2011-08-01 | | Quoted Standard | GB/T 21782.9-2010 | | Adopted Standard | ISO 8130-5-1992.IDT | | Regulation (derived from) | Announcement of Newly Approved National Standards No. 6 of 2010 (total 161) | | Issuing agency(ies) | General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China | | Summary | This standard specifies the powder -air mixture flow measurement method, This approach reflects the powder coating industry practices, the study came to the conclusion that: factors affecting liquidity powder coating composition, density, particle shape, particle size distribution, as well as particle agglomeration and the nature of the charge acceptance of friction, Note: As we all know, powder conveying and spraying characteristics depend on the accumulation of powder in the air and the flow properties of the state, the industry believes that some of the methods compared to the sometimes weep for assessing the mobility of body powder flow angle approach is more practical significance, based on the current angle method, when the powder flow through the vertical to the horizontal plane of the funnel, will be able to form a tapered angle measured with good mobility paralysis Activity of the powder than the paralysis of poor quality of the powder formed by the same taper angle is small, the use of mobile angle method, the objective is difficult to obtain accurate measurements, the surface and the powder is as a single test, but in the actual construction of the powder and the air is mixed, | GB/T 21782.5-2010: Coating powders -- Part 5: Determination of flow properties of a powder/air mixture
---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.
Coating powders. Part 5. Determination of flow properties of a powder/air mixture
ICS 87.040
G50
National Standards of People's Republic of China
Powder Coatings Part 5.
Determination of fluidity of powder air mixtures
Coatingpowders-
Part 5. Determinationofflowpropertiesofapowder/airmixture
(ISO 8130-5..1992, IDT)
2010-09-26 release
2011-08-01 implementation
General Administration of Quality Supervision, Inspection and Quarantine of the People 's Republic of China
China National Standardization Management Committee released
Foreword
GB/T 21782-2010 "powder coating" consists of 14 parts, the structure and its corresponding international standards are as follows.
Part 1. Determination of particle size distribution by sieving method (ISO 8130-1..1992, IDT);
- Part 2. Determination of density by gas ratio gravimetric method (ISO 8130-2..1992, IDT);
- Part 3. Determination of density by liquid displacement pycnometer method (ISO 8130-3..1992, IDT);
- Part 4. Calculation of the lower limit of the explosion (ISO 8130-4..1992, IDT);
- Part 5. Determination of fluidity of powder air mixtures (ISO 8130-5..1992, IDT);
Part 6. Determination of the gelation time of thermosetting powder coatings at a given temperature (ISO 8130-6..1992, IDT);
- Part 7. Determination of mass loss during baking (ISO 8130-7..1992, IDT);
- Part 8. Evaluation of storage stability of thermosetting powders (ISO 8130-8..1994, IDT);
- Part 9. Sampling (ISO 8130-9..1992, IDT);
- Part 10. Determination of deposition efficiency (ISO 8130-10..1998, IDT);
- Part 11. Determination of fluidity of tilting plates (ISO 8130-11..1997, IDT);
- Part 12. Determination of compatibility (ISO 8130-12..1998, IDT);
Part 13. Particle size analysis by laser diffraction (ISO 8130-13..2001, IDT);
- Part 14. Terminology (ISO 8130-14..2004, IDT).
This part is Part 5 of GB/T 21782-2010.
This part uses the translation method equivalent to ISO 8130-5..1992 "Powder Coatings Part 5 Powder Air Mixture Flowability
Set "(English version).
For ease of use, this section has made the following editorial changes.
Remove Appendix B of the International Standard ISO 8130-5.
Appendix A to this section is an informative appendix.
This section is proposed by the China Petroleum and Chemical Industry Association.
This part is headed by the National Committee for Standardization of Coatings and Pigments (SAC/TC5).
This part of the drafting unit. Guangdong Entry-Exit Inspection and Quarantine Bureau, CNOOC Changzhou Paint Chemical Research Institute.
The main drafters of this part. Lin Hongxiong, Zheng Jianguo, Shen Wenjie, Chen Qiang, Zhao Ling, Chen Gufeng, Li Zhengjun, Yue Dalei.
Powder Coatings Part 5.
Determination of fluidity of powder air mixtures
1 Scope
This part of GB/T 21782 specifies the determination of the flowability of the powder air mixture. This method reflects the powder coating industry
practice.
The study concluded that the factors that affect the mobility of the powder coating composition, density, particle shape, particle size distribution, as well as the grain
Sub-agglomeration and acceptance of triboelectric charge properties.
Note. It is well known that the transport and spray characteristics of the powder are largely dependent on the flow properties of the powder in the air and in the stacked state. Industry insiders recognize
This method is more practical than the method of evaluating the flow of powder ontology. By flow angle method, when the powder flows through
Vertical cone to the horizontal plane, you can measure the formation of the cone angle. The powder with good flowability is formed by the same mass of powder with poor mobility
Taper angle is small. The use of flow angle method, it is difficult to obtain accurate measurement of the objective value, but only for the powder for a separate test, but in the actual construction
When the powder and air are mixed.
2 normative reference documents
The terms of the following documents are the terms of this part by reference to this part of GB/T 21782. Any reference to the date of the text
, All subsequent amendments (excluding corrigenda) or revisions do not apply to this part, however, encouragement under this section
The parties to the agreement study whether the latest version of these documents can be used. For undated references, the latest edition of this document applies
section.
GB/T 21782.9-2010 Powder coatings - Part 9. Sampling (ISO 8130-9..1992, IDT)
3 principle
In the absence of air flow conditions, the provisions of the quality of the powder coating in the container. In the standard atmospheric pressure and temperature conditions, with clean
The net dry air is fluidized to determine the rate of fluidization and after fluidization and the rate at which the fluidized powder flows through a particular orifice.
The fluidization factor φ and the powder flow rate (flow factor) R, the fluidization factor φ and the powder flow rate R are used to characterize the powder transport
And the characteristics of spraying.
4 equipment
4.1 Equipment for testing fluidity. consists of a fluidized container with a toroidal flow port on the wall and a height of the instrument in the test vessel. Simultaneously
It also includes instruments that weigh the powder quality flowing through the flow port.
Note. Figure 1 is a suitable apparatus, which will be described below. You can also use devices that give similar results.
Typical equipment is composed of the individual units described in 4.1.1 to 4.1.3.
4.1.1 Fluidized powder container (container A). outer diameter of about 110mm, diameter of about 100mm, height of not less than.200mm, by the transparent
Of methyl methacrylate, the bottom by the uniform porous copper discs, the largest pore size of about 40μm.
Note. A 5 mm thick disk can have an air flow rate of about (200 ± 10) L/h at atmospheric pressure of 5 kPa or more and is suitable for use.
The annular flow mouth D with an outer diameter of 4 mm can be plugged with a plug E, which is suitable for the position on the container wall, generally on a cast copper disc
Side 10mm Department.
4.1.2 Air conditioning unit B. Adjust the air flow with the flow meter F.
4.1.3 Container C. To have sufficient volume, install the powder at the time of the test powder flow rate (see Figure 1).
4.2 Dry air supply. Have enough air to supply the test.
Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 21782.5-2010_English be delivered?Answer: Upon your order, we will start to translate GB/T 21782.5-2010_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time. Question 2: Can I share the purchased PDF of GB/T 21782.5-2010_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 21782.5-2010_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to [email protected]. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.
|