|
US$2439.00 · In stock
Delivery: <= 14 days. True-PDF full-copy in English will be manually translated and delivered via email.
GB/T 20174-2019: Petroleum drilling and production equipment - Drill-through equipment
Status: Valid GB/T 20174: Evolution and historical versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | Status | PDF |
| GB/T 20174-2019 | English | 2439 |
Add to Cart
|
14 days [Need to translate]
|
Petroleum drilling and production equipment - Drill-through equipment
| Valid |
GB/T 20174-2019
|
| GB/T 20174-2006 | English | RFQ |
ASK
|
13 days [Need to translate]
|
Petroleum and natural gas industries -- Drilling and production equipment -- Drill-through equipment
| Obsolete |
GB/T 20174-2006
|
PDF similar to GB/T 20174-2019
Basic data | Standard ID | GB/T 20174-2019 (GB/T20174-2019) | | Description (Translated English) | Petroleum drilling and production equipment - Drill-through equipment | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | E92 | | Classification of International Standard | 75.180.10 | | Word Count Estimation | 122,150 | | Date of Issue | 2019-03-25 | | Date of Implementation | 2019-10-01 | | Older Standard (superseded by this standard) | GB/T 20174-2006 | | Quoted Standard | GB/T 228.1; GB/T 230.1; GB/T 231.1; GB/T 2828.1; GB/T 4340.1; GB/T 20972.1; GB/T 20972.2; GB/T 20972.3; GB/T 22513; ISO 9712; API SPEC 5CT; API SPEC 5DP; API 6AF2; API 6X; API SPEC 16A; API SPEC 20E; API SPEC 20F; API SPEC Q1 | | Issuing agency(ies) | State Administration for Market Regulation, China National Standardization Administration | | Summary | This standard specifies the design, material, welding, quality control, marking, storage and transportation requirements for drilling and drilling equipment for gas extraction wells. This standard applies to the following equipment: a) ram blowout preventer; b) ram, ram rubber core and top seal; c) annular blowout preventer; d) annular blowout preventer sealing rubber core; e) one-piece BOP; f) hydraulic connectors (wellhead, riser or LMRP); g) drilling crosses and footprint shorts; h) adapters; i) mandrels; j) one-piece connections; k) clamps . Dimensional interchangeability is limited to end and outlet connections. Typical equipment mentioned in this standard is shown in Figure 1, Figure 2 and Figure 3. This standard does not apply to the field use and field test of drill-through equipment. | GB/T 20174-2019: Petroleum drilling and production equipment - Drill-through equipment---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.
(Oil and gas drilling equipment)
ICS 75.180.10
E92
National Standards of People's Republic of China
Replace GB/T 20174-2006
Oil and gas drilling equipment
Published on.2019-03-25
2019-10-01 implementation
State market supervision and administration
China National Standardization Administration issued
Content
Foreword III
1 Scope 1
2 Normative references 4
3 Terms and Definitions 6
4 Abbreviations 12
5 Design requirements 12
5.1 Dimensions 12
5.2 Working conditions 13
5.3 Design requirements for equipment specifications 14
5.4 Design Method 32
5.5 Design Confirmation 34
5.6 File 35
5.7 BOP and hydraulic connector performance test 35
5.8 Operating Manual Requirements 58
5.9 Technical Data Sheet 58
5.10 Unit conversion 59
6 Material Requirements 59
6.1 General 59
6.2 Written specification 59
6.3 Pressure bearing parts 60
6.4 Pressure control unit 66
7 Welding requirements 67
7.1 General 67
7.2 Weld design and structure 67
7.3 Welding Control 68
7.4 Welding procedure and performance identification 73
7.5 Other requirements 74
8 Quality Control Requirements 78
8.1 General 78
8.2 Measurement and test equipment 78
8.3 Quality Control Personnel Qualification 78
8.4 Quality Control Requirements for Equipment and Parts 79
8.5 Quality Control Requirements for Special Equipment and Parts 79
8.6 Quality Control Record Requirements 90
8.7 Failure Report 92
9 Identification requirements 92
9.1 General 92
9.2 Identification Type 92
9.3 Special coding requirements for equipment 93
9.4 Product Code (PDC) 95
10 Storage and Transportation 98
10.1 Storage for more than 30 days 98
10.2 Transportation 99
Appendix A (Normative) Conversion of US Customary Units and International System of Units (Metric System) 100
Appendix B (Normative) Identification of Heat Treatment Equipment 104
Appendix C (Normative) Charpy V-notch impact test for welding evaluation 107
Appendix D (informative) Gas Seal Test 109
Appendix E (Normative) Certificate of Conformity (COC) 111
Appendix F (Informative Appendix) Procurement Guide 114
Appendix G (Normative Appendix) Failure Report 117
Reference 118
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
This standard replaces GB/T 20174-2006 "Drilling and Production Equipment for Oil and Gas Industry Drilling and Passing Equipment", and GB/T 20174-
Compared with.2006, the main technical changes are as follows.
--- Added the relevant content of the integrated BOP;
--- Revised the schematic diagram of the ground drilling equipment and the schematic diagram of the underwater drilling equipment (see Figure 1, Figure 2);
--- Increased the terms and definitions of closure ratio, key areas, critical dimensions, etc.;
--- Increased acronyms such as COC, FAT, MOPFLPS;
--- Increased rated pressure levels of 6.9 MPa (1000 psi) and 172.4 MPa (25,000 psi) (see Table 2);
--- Increased the temperature grade of the metal material, from the original three temperature levels to six, increasing the temperature limit of 177 ° C
(See Table 3);
--- Increased the non-metallic seal temperature level to the lowest temperature, continuous high temperature, extreme high temperature representation method, the representation method from the original
2 digits become 3 digits (see Table 4);
--- Increased hydraulic connector requirements for locking (see 5.3.11.7);
--- Increased the requirements for test piles (see 5.4.8);
--- Increased the purpose, procedures, and record requirements for design verification tests such as ring and ram blowout preventers (see 5.7);
--- Increased the design confirmation test content, such as. low pressure seal minimum operating pressure test if the wellbore pressure is zero (see 5.7.3.1.1),
Minimum operating pressure test for low pressure seals with well pressure (see 5.7.3.1.2), shear diameter design range test (see 5.7.3.4.2), partial
Heart shear test (see 5.7.3.4.3), lateral force shear test (see 5.7.3.4.4), annular blowout preventer extended range operating performance test
(see 5.7.3.12);
--- Increased design temperature confirmation test content, such as. annular blowout preventer continuous working temperature design confirmation test (see 5.7.3.17), ring
Low-pressure path performance test of the blowout preventer (see 5.7.3.19);
--- Increased the requirements for weld repairs and traceability requirements for metal parts in written specifications (see 6.2.1);
--- Increased the performance requirements of non-standard materials for pressure parts (see 6.3.1, Table 29);
--- Increased material requirements for pressure control parts (see 6.4);
--- Modified the requirements for post-weld heat treatment (7.3.7);
--- Increased the requirements for filling material identification and chemical composition analysis in the performance qualification of the welding process (see 7.4.3);
--- Increased the requirements for visual inspection of welders (see 7.4.8);
--- Increased the hardness test of the surfacing layer (see 7.5.1.2.5);
--- Increased the hardness test requirements for the actual value of the hardness test of pressure parts and pressure control parts at the point of location (see
8.5.1.4); the actual value of the weld hardness test shall be indicated on the part close to the test position (see 8.5.1.16);
--- Increased the content of the diameter test, canceled the 30min aging requirements of the ram blowout preventer (see 8.5.7.4.2);
--- Increased the requirements for the housing gasket area in the bulk hydrostatic strength test (see 8.5.7.6.2);
--- Increased the test requirements for pressure-bearing components when BOP or hydraulic connectors are transported separately (see 8.5.7.8.6);
--- Removed the requirements for the repair and repair of the canonical Appendix B (see Appendix B of the.2006 edition);
--- Deleted the design confirmation procedure for the informative Appendix C Ground Safety Valve (SSV) and Underwater Safety Valve (USV) (see.2006 edition)
Appendix C);
--- Deleted the design and rating of the high-temperature device for the informative Appendix D (see Appendix D of the.2006 edition);
--- Added normative Appendix E certificate of conformity (see Appendix E);
--- Added the Charpy V-notch impact test for the normative Appendix C welding assessment (see Appendix C).
Please note that some of the contents of this document may involve patents. The issuing organization of this document is not responsible for identifying these patents.
This standard is proposed and managed by the National Technical Committee for Standardization of Oil Drilling Equipment and Tools (SAC/TC96).
This standard was drafted. Petroleum Industry Well Control Equipment Quality Supervision and Inspection Center, China Petroleum Chuanqing Drilling Engineering Company, Hebei North China Stone
Oil Rongsheng Machinery Manufacturing Co., Ltd., China National Petroleum Corporation Exploration and Development Research Institute, Sichuan Gems Machinery Drilling Equipment Limited
Responsible company, Tarim Oilfield Branch, Shanghai Shenkai Petroleum Equipment Co., Ltd.
The main drafters of this standard. Zhang Zhidong, Zhang Xianglai, Sun Hongxiang, Zeng Lian, Xu Hongqi, Chen Junfeng, Liu Xuemei, Xu Yongjun, Chen Shaowei,
Lin Faquan, Meng Qingrong, Zhang Chuan, Yao Yiyuan, Chen Zhangrui, Zeng Xia, Ye Guowu, Xu Mao, Qin Liu, Liu Ming.
The previous versions of the standards replaced by this standard are.
---GB/T 20174-2006.
Oil and gas drilling equipment
1 Scope
This standard specifies the design, materials, welding, quality control, marking, storage and transportation requirements for drilling and drilling equipment used in oil and gas wells.
This standard applies to the following equipment.
a) ram blowout preventer;
b) gates, gate rubber cores and top seals;
c) an annular blowout preventer;
d) annular blowout preventer sealant;
e) integrated blowout preventer;
f) hydraulic connectors (wellhead devices, risers or LMRP);
g) Drilling cross and shorting of the place;
h) adapter;
i) mandrel;
j) single piece connection;
k) Clamp.
Dimensional interchangeability is limited to end and outlet connections.
Typical equipment mentioned in this standard is shown in Figures 1, 2 and 3.
This standard does not apply to field use and field tests of drill-through equipment.
|