GB/T 5106-2012 English PDFUS$909.00 · In stock
Delivery: <= 7 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 5106-2012: Straight cylindrical involute splines -- Gauge Status: Valid GB/T 5106: Historical versions
Basic dataStandard ID: GB/T 5106-2012 (GB/T5106-2012)Description (Translated English): Straight cylindrical involute splines -- Gauge Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: J42 Classification of International Standard: 17.040.30 Word Count Estimation: 41,494 Older Standard (superseded by this standard): GB/T 5106-2006 Quoted Standard: GB/T 1957-2006; GB/T 3478.1; GB/T 3478.2; GB/T 3478.3; GB/T 3478.4; GB/T 3478.5; GB/T 3478.6; GB/T 3478.7; GB/T 3478.8; GB/T 3478.9 Regulation (derived from): National Standards Bulletin No. 41 of 2012 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This standard specifies the Straight cylindrical involute spline gauges terms and definitions, symbols and description, classification, type and size parameters, tolerances, requirements, test methods, marking and packaging. Specified in this standard gau GB/T 5106-2012: Straight cylindrical involute splines -- Gauge---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.Straight cylindrical involute splines. Gauge ICS 17.040.30 J42 National Standards of People's Republic of China Replacing GB/T 5106-2006 Straight cylindrical involute spline gauges Issued on. 2012-12-31 2013-10-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released Table of ContentsIntroduction Ⅲ 1 Scope 1 2 Normative references 1 3 Terms and definitions Symbol Description 1 and 4 5 Category 2 6 type and size parameters 4 7 Tolerance 15 8 requires 18 9 18 test method Marking and packaging 10 21 Regulation controversial decision to use rule 22 Appendix A (normative) amount Annex B (informative) measuring a workpiece spline path, external splines large diameter smooth limit gauge 24 Annex C (informative) spline gauge shape the structure and size 25 Annex D (informative) Calculation example gauge cross bar and rod spacing distance MRe MRi 28 Figure 1 a gauge test workpiece space width or tooth thickness limit size of 4 3 Figure 2 integrated through the end ring 5 FIG. 3 through the end ring with integrated proofing plug 6 4 part-toothed ring gauges pass 7 FIG. 5 through part-toothed ring gauges with proof plug 7 Integrated end stop ring 8 6 Integrated end stop ring with 7 proofing plug 9 8 part-toe ring gear 10 9 non-full tooth toe ring with proofing plug 10 FIG. 10 integrated through the end plug 11 11 non-full gear through the end plug 12 Integrated end stop 12 plug 12 13 non-stop the whole tooth end plug 13 14 workpiece spline teeth Teeth ≤30 part-plug of teeth 15 15 gauge or thickness of the tooth space width tolerance position 17 16 odd large diameter gear plug detection 19 17 plug gauge tooth thickness detector 20 18 ring gauge space width detection 20 Figure A.1 and the effective length of the spline fit length 23 Figure B.1 smooth limit plug gauge 24 Figure B.2 smooth limit ring 24 Figure C.1 splined ring shape structure 25 Figure C.2 spline plug shape structure 26 Figure D.1 plug in the tooth thickness tolerance band and the workpiece spline space width tolerance zone 29 Figure D.2 rod diameter is calculated to detect the amount of plug gauge 29 Figure D.3 ring space width tolerance band and the workpiece external spline tooth thickness tolerance zone 33 Figure D.4 calculate the amount of ring gauge detecting rod diameter 34 Table 1 Symbol and Description 1 Table 2 gauge name, code, functions, features and the use of Rule 3 Table 3 through the end of the ring size parameters 5 Table 4-way ring gauges with proofing plug size parameters 6 Table 5 end-stop ring size parameters 8 Table 6 end stop ring with proofing plug size parameters 9 Table 7 through the end of the plug gauge size parameters 11 Table 8 size parameters only end plug 13 The minimum length of the table 9 gauge measuring section 14 Table 10 Non-full tooth gauge the number of teeth of two sector selection 14 Table 11 manufacturing tolerances and position element value 15 18 Table 12 individual tolerance Table C.1 spline ring gauge Dimensions 25 Table C.2 spline plug dimensions 27ForewordThis standard was drafted in accordance with GB/T 1.1-2009 given rules. The reference standard ISO 4156-3.2005 "Straight cylindrical involute splines (Metric module, side fit) - Part 3. Test" and GB/T 3478.5-2008 "Straight cylindrical involute splines (Metric module, side fit) - Part 5. Inspection" in preparation. This standard compared with GB/T 5106-2006, the main changes are as follows. --- Added "part-toothed ring gauges pass", "part-toothed ring gauges pass with proof plug," "non-full gear through the end plug" Three Kinds of gauge; --- An increase in the measurement of the workpiece spline path, external splines large diameter smooth limit gauge; --- Increasing the gauge cumulative pitch tolerance (indexing tolerance) notes; --- Increasing the gauge of test methods; --- Original standard Appendices Appendix D A modified standard cost; --- Increase in Appendix A "gauge usage rule controversial decision," Appendix B "measure workpiece spline path, external splines of the large diameter smooth pole Limited regulation ", Appendix C" spline gauge shape the structure and size "; --- Modify the original standard wrong, and made changes to the editorial. The standard proposed by China Machinery Industry Federation. The standard measuring instrument by the National Standardization Technical Committee (SAC/TC132) centralized. This standard is drafted by. Heng Fung Tools Co., Ltd. Participated in the drafting of this standard. Jiangsu Province Institute of Metrology, China Institute of Metrology, Chengdu Tool Research Institute Co., Ltd., Heiner iron Fu shaft Co., Shanghai Automotive Transmission Co., Ltd. The main drafters of this standard. Chen Ziyan, HE Qin Song, Xia Yongsheng, Yang Min Li, Lu promising, Jiang Zhigang, Goal Orientation, Zhao, Zhao Lin, Xu Jianxing. This standard replaces the standards previously issued as follows. --- GB/T 5106-1985, GB/T 5106-2006. Straight cylindrical involute spline gauges1 ScopeThis standard specifies the Straight cylindrical involute spline gauges (hereinafter referred to as "gauge") terms and definitions, symbols and description, category, type And size parameters, tolerances, requirements, and other test methods, marking and packaging. This standard specifies the amount of regulation applicable to test GB/T 3478 prescribed pitch diameter ≤180mm spline. Pitch circle diameter > 180mm or GB/T 3478 not specified spline, reference may be used.2 Normative referencesFor this article the following documents are indispensable. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document. GB/T 1957-2006 smooth limit gauge the technical conditions GB/T 3478 (all parts) Straight cylindrical involute splines (Metric module, side fit)3 Terms and DefinitionsTerms and definitions GB/T established in 3478.1 apply to this document.4 Symbol and descriptionTable symbols and instructions listed in this document apply to 1. Table 1 Symbol and description Symbol Description Unit z number of teeth - m Modulus mm αD standard pressure angle (°) D pitch circle diameter mm Db base diameter mm DFemax workpiece external splines involute starting circle diameter maximum mm Splined inner DFimin workpiece involute termination circle diameter minimum mm Deemax workpiece external splines large diameter maximum mm Dimin spline path within the workpiece minimum mm ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 5106-2012_English be delivered?Answer: Upon your order, we will start to translate GB/T 5106-2012_English as soon as possible, and keep you informed of the progress. The lead time is typically 4 ~ 7 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 5106-2012_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 5106-2012_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 5106-2012?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 5106-2012 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
