GB/T 8177-2024 English PDFUS$279.00 ยท In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 8177-2024: Internal micrometers with two-point contact Status: Valid GB/T 8177: Historical versions
Basic dataStandard ID: GB/T 8177-2024 (GB/T8177-2024)Description (Translated English): Internal micrometers with two-point contact Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: J42 Classification of International Standard: 17.040.30 Word Count Estimation: 14,127 Date of Issue: 2024-04-25 Date of Implementation: 2024-11-01 Older Standard (superseded by this standard): GB/T 8177-2004 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration GB/T 8177-2024: Internal micrometers with two-point contact---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.ICS 17:040:30 CCSJ42 National Standards of People's Republic of China Replace GB/T 8177-2004 Two-point inside micrometer Released on 2024-04-25 2024-11-01 Implementation State Administration for Market Regulation The National Standardization Administration issued Table of ContentsPreface III 1 Scope 1 2 Normative references 1 3 Terms and Definitions 1 4 Type and basic parameters 1 5 General 2 6 Test conditions 4 7 Inspection methods 5 8 Marking and packaging 6 References 7ForewordThis document is in accordance with the provisions of GB/T 1:1-2020 "Guidelines for standardization work Part 1: Structure and drafting rules for standardization documents" Drafting: This document replaces GB/T 8177-2004 Two-point internal micrometer: Compared with GB/T 8177-2004, except for structural adjustment and editing, In addition to the changes in performance, the main technical changes are as follows: a) Added the type of rod-type internal diameter micrometer in the range (see Chapter 1); b) The definition of two-point internal micrometer has been changed (see 3:1, 3:1 of the:2004 edition); c) The two-point internal micrometer type has been changed (see 4:1, 4:1 of the:2004 edition); d) Added two-point internal diameter micrometer to measure the axial movement between the screw and the nut (see 5:3); e) The hardness requirements of the measuring surface have been changed (see 5:5:1, 5:5:1 of the:2004 edition); f) The requirements for digital display devices have been deleted (see 5:7 of the:2004 edition); g) The allowable variation of the length dimension of the two-point internal micrometer has been changed (see 5:8:2, Table 1, and 5:9:2 of the:2004 edition); h) The tool for adjusting the zero position of the two-point internal micrometer has been changed (see 5:9:1, 5:10:1 of the:2004 edition); i) Added the hardness value, indication error and parallelism requirements for the calibration caliper measuring surface (see 5:9:2); j) Added the inspection conditions for two-point internal micrometer (see Chapter 6); k) The inspection method for indication error has been changed (see 7:1, 6:1 of the:2004 edition); l) The inspection method for the allowable variation of length dimension has been changed (see 7:2, 6:2 of the:2004 edition); m) Added the inspection method for calibration gauge indication error and parallelism of two working surfaces (see 7:3): Please note that some of the contents of this document may involve patents: The issuing organization of this document does not assume the responsibility for identifying patents: This document was proposed by the China Machinery Industry Federation: This document is under the jurisdiction of the National Technical Committee for Standardization of Measuring Tools and Instruments (SAC/TC132): This document was drafted by: Chengdu Xincheng Measuring Tools Co:, Ltd:, Guilin Measuring Tools and Blades Co:, Ltd:, Chengdu Tools Research Institute Co:, Ltd: Guilin Guanglu Digital Measurement and Control Co:, Ltd:, Harbin Measuring Tools and Cutting Tools Group Co:, Ltd:, Qingliang Technology (Shenzhen) Co:, Ltd:, Qinghai Measuring Tools Tools and Blades Co:, Ltd:, Suzhou Guoliang Measuring Tools Technology Co:, Ltd: The main drafters of this document are: Wang Ting, Huang Longrong, Wei Gaihong, Mei Yingtao, Xu Gang, He Yixian, Yan Liexue, Zhang Wei, Sun Yunchen, Ma Shibin, Zhao Yonghai and Zhao Jian: This document was first published in 1987; when it was first revised in:2004, GB/T 9057-1988 "Single-rod internal micrometer" was incorporated; This is the second revision: Two-point inside micrometer1 ScopeThis document specifies the types and basic parameters of two-point internal micrometers (including connecting rod internal micrometers and single rod internal micrometers): General rules, inspection conditions, inspection methods, marking and packaging: This document is applicable to graduation values of 0:01mm, 0:001mm, 0:002mm, 0:005mm, and micrometer screw pitch of 0:5mm or 1:0mm, the upper limit of measurement is not more than 6000mm, the rod-type internal diameter micrometer and the single-rod internal diameter micrometer (excluding electronic digital internal diameter micrometer) Design, manufacture and inspection of scales:2 Normative referencesThe contents of the following documents constitute the essential clauses of this document through normative references in this document: For referenced documents without a date, only the version corresponding to that date applies to this document; for referenced documents without a date, the latest version (including all amendments) applies to This document: GB/T 17163 Basic terms for geometric measuring instruments GB/T 17164 Terminology of geometric measuring instruments Product terminology3 Terms and definitionsThe terms and definitions defined in GB/T 17163 and GB/T 17164 and the following apply to this document: 3:1 An internal dimension measuring instrument that uses the principle of screw pair to read the distance between the spherical measuring surfaces at both ends of the main body: Note: It is referred to as internal micrometer: Among them, the one without extension rod, i:e: the integral structure, is also called single-rod internal micrometer:4 Types and basic parameters4:1 Type The schematic diagram of the connecting rod type internal diameter micrometer is shown in Figure 1, and the schematic diagram of the single rod type internal diameter micrometer is shown in Figure 2: The illustrations are for illustrative purposes only: ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 8177-2024_English be delivered?Answer: Upon your order, we will start to translate GB/T 8177-2024_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 8177-2024_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 8177-2024_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 8177-2024?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 8177-2024 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
