GB/T 38568-2020 PDF English
Search result: GB/T 38568-2020_English: PDF (GB/T38568-2020)
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Name of Chinese Standard | Status |
| GB/T 38568-2020 | English | 85 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Determination of growth phenotype for industrial microbial strain -- Microdroplet turbidity
| Valid |
BUY with any currencies (Euro, JPY, GBP, KRW etc.): GB/T 38568-2020 Related standards: GB/T 38568-2020
PDF Preview: GB/T 38568-2020
GB/T 38568-2020: PDF in English (GBT 38568-2020) GB/T 38568-2020
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 07.080
A 21
Determination of growth phenotype for
industrialmicrobial strain - Microdroplet turbidity
ISSUED ON: MARCH 31, 2020
IMPLEMENTED ON: MARCH 31, 2020
Issued by: State Administration for Market Regulation;
Standardization Administration of the People’s Republic of
China.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Terms and definitions ... 4
4 Principle ... 4
5 Reagents or materials ... 4
6 Instruments and apparatuses ... 5
7 Determination steps ... 6
8 Result analysis ... 7
Determination of growth phenotype for
industrialmicrobial strain - Microdroplet turbidity
1 Scope
This Standard specifies the method for the determination of growth phenotype
for industrialmicrobial strain by microdroplet turbidity.
This Standard applies to the determination of the growth phenotype of bacteria,
fungi and microalgae strains for industrial fermentation.
2 Normative references
The following documents are indispensable for the application of this document.
For dated references, only the dated version applies to this document. For
undated references, the latest edition (including all amendments) applies to this
document.
GB/T 6682, Water for analytical laboratory use - Specification and test
methods
GB/T 14926.43, Laboratory animal - Bacteriological monitoring - Staining,
media and reagents
3 Terms and definitions
The following terms and definitions are applicable to this document.
3.1 Reference strain
The identified stock strain, whose fermentation performance is clear, for
fermentation production.
4 Principle
Generate single-cell-encapsulated droplets by the micro-fluidic chip; culture it.
Calculate the growth rate according to the area of the bacteria in the droplets.
5 Reagents or materials
Unless otherwise specified, all the reagents are analytical reagents.
7 Determination steps
7.1 Strain activation
7.1.1 Prepare solid plates and liquid culture media corresponding to industrial
microorganisms according to the methods that are given in GB/T 14926.43. Use
a sterile inoculating loop to dip the reference strain and the strain preservation
bacteria solution of the to-be-evaluated strain respectively; draw a line on the
solid plate; select the corresponding temperature and other conditions to
perform cultivation according to the production process parameters, until a
single colony grows; respectively pick 3 reference strains and 3 single colonies
of to-be-evaluated strains; inoculate them into a test tube that contains 5 mL of
liquid medium; select the corresponding temperature and speed according to
the production process parameters; cultivate to the logarithmic phase.
7.1.2 Pick a monoclone of the microorganism strain from the activated plate
petri dish; place it in a container of 5 mL of liquid medium; select the
corresponding temperature and speed according to the production process
parameters; cultivate to the stable period. After removing the supernatant, add
the PBS solution and repeat the washing 3 times.
7.2 Selection of microbial liquid concentration
Use the basal medium to dilute to obtain a cell suspension concentration of
about 6 × 105 CFU/mL.
7.3 Preparation of agarose solution
Use the analytical balance to weigh 0.02 g of ultra-low melting point agarose;
place it in a sterile EP tube; add 1 mL of sterilized basal medium to it; heat to
dissolve; prepare it into a 2% (mass concentration) solution. Use a 0.22 μm
sterile filter to filter while it is hot; prepare it when necessary.
7.4 Single cell droplet generation
7.4.1 Respectively take 500 μL of the microbial liquid and the agarose solution
in equal volumes and mix them.
7.4.2 Take a chip; respectively add 200 μL of fluorocarbon oil to the oil phase
inlet of the chip and 100 μL of low melting point agarose to the water phase
inlet; connect the syringe to the chip outlet.
7.4.3 Place the chip on the hot plate (temperature stability of ±1°C, range at
30 °C ~ 37 °C); fix the plunger of the syringe at the 2 mL mark; let the liquid
enter the chip through the negative pressure in the syringe; start to generate
droplets. It takes about 2 minutes to generate droplets.
......
Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.
|