HOME   Cart(0)   Quotation   About-Us Policy PDFs Standard-List
www.ChineseStandard.net Database: 189760 (18 Oct 2025)

GB/T 37676-2019 PDF English

US$150.00 · In stock · Download in 9 seconds
GB/T 37676-2019: High Speed Precision Hot Upsetting Forgings - Technological Specification
Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure
Status: Valid
Standard IDContents [version]USDSTEP2[PDF] deliveryName of Chinese StandardStatus
GB/T 37676-2019English150 Add to Cart 0-9 seconds. Auto-delivery High Speed Precision Hot Upsetting Forgings - Technological Specification Valid

Excerpted PDFs (Download full copy in 9 seconds upon purchase)

PDF Preview: GB/T 37676-2019
      

Similar standards

GB/T 37683   GB/T 37057   GB/T 37679   

GB/T 37676-2019: High Speed Precision Hot Upsetting Forgings - Technological Specification

---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT37676-2019
NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 77.140.85 J 32 High Speed Precision Hot Upsetting Forgings - Technological Specification ISSUED ON: JUNE 4, 2019 IMPLEMENTED ON: JANUARY 1, 2020 Issued by: State Administration for Market Regulation; Standardization Administration of the People’s Republic of China.

Table of Contents

Foreword ... 3 1 Scope ... 4 2 Normative References ... 4 3 Terms and Definitions ... 5 4 Design Principles ... 5 High Speed Precision Hot Upsetting Forgings - Technological Specification

1 Scope

This Standard stipulates the technological specification of high speed precision hot upsetting forgings (hereinafter referred to as “forgings”), including general principles, determination of technological parameters, preparation of forging billets, billet heating, requirements of moulds and selection of equipment. This Standard is applicable to the technological design for steel precision forgings which adopt hot upsetting for molding, and with the production pace of 50 PCS/min and above, the mass of below 7.5 kg, and the outer diameter of not more than 180 mm.

2 Normative References

The following documents are indispensable to the application of this document. In terms of references with a specified date, only versions with a specified date are applicable to this document. In terms of references without a specified date, the latest version (including all the modifications) is applicable to this document. GB/T 699 Quality Carbon Structural Steels; GB/T 700 Carbon Structural Steels; GB/T 1299 Tool and Mould Steels; GB/T 1591 High Strength Low Alloy Structural Steels; GB/T 3077 Alloy Structure Steels; GB/T 5216 Structural Steels with Specified Hardenability Bands; GB/T 8541 Terminology of Forging and Stamping; GB 13318-2003 General Rules for Safety and Environmental Conservation of Forging Production; GB/T 15712 Micro-alloyed Medium Carbon Steels; GB/T 18254 High-carbon Chromium Bearing Steel; GB/T 28417 Carbon Bearing Steel; 4.1.7 Mould parts that contact forgings shall be cooled down. Generally speaking, the cooling medium of moulds shall select water. Avoid directly spraying forgings with the cooling medium. 4.1.8 In terms of forgings with a relatively large amount of deformation, proper lubricating agent should be added to the cooling medium. 4.1.9 The replacement of moulds should be conducted in sets. 4.1.10 Post-forging afterheat should be utilized in the thermal treatment of forgings. 4.1.11 During the whole production process, consider adopting anti-collision measures for forgings. 4.1.12 The operating environment shall comply with the requirements in 5.2 in GB 13318-2003; personnel shall satisfy the requirements in 10.2 in GB 13318-2003; safety and environmental protection technological measures shall comply with the requirements in Chapter 9 in GB 13318-2003. 4.2 Determination of Technological Parameters 4.2.1 Deformation temperature 4.2.1.1 Deformation temperature shall be within the Austenite zone, which is above the recrystallization temperature. In order to avoid over-heating and over-burning phenomena, heating temperature should be within 1,150 °C ~ 1,280 °C. Specifically speaking, heating temperature of bearing steel should not exceed 1,180 °C. On the premise of thorough cooling of moulds, the heating temperature should approach the upper limit. 4.2.1.2 After forging, the temperature should be quickly cooled down to below AC1, so as to avoid grain growth. 4.2.1.3 When afterheat is utilized for thermal treatment, the final forging temperature of forgings shall satisfy the requirements of the subsequent thermal treatment. 4.2.2 Degree of deformation 4.2.2.1 Degree of deformation of the various stations shall avoid large grains caused by final accumulative deformation. 4.2.2.2 The selection of the degree of deformation shall consider the influence of deformation mode on allowable deformation. 4.2.3 Deformation force Numerical value simulation should be adopted to analyze and calculate deformation force, or, nomograph or empirical formula may also be adopted for calculation. 4.2.1.7 4.4 Billet Heating 4.4.1 Billet heating shall adopt the mode of integral-bar induction heating. Furthermore, there shall be temperature detection; high and low temperature alarm and shutdown functions. 4.4.2 The selection of the specification of the sensor shall match with the diameter of the heating billets, so as to avoid low efficiency of heating. 4.4.3 The billet feeding pace shall comprehensively consider factors like billet dimensions, heating temperature and forging equipment, etc. It shall be on the premise that the heating temperature of billets shall evenly reach the technological requirement. 4.5 Requirements of Mould 4.5.1 The precision of moulds shall satisfy precision requirements of forgings, such as: dimensions, shape and position tolerances, etc. 4.5.2 Convex mould, concave mould and ejector pole should adopt nitridation for surface treatment, so as to enhance the surface hardness and abrasive resistance of moulds. The surface roughness value of moulds shall be not more than Ra0.8 m. 4.5.3 Concave mould and ejector pole should be designed into hollow structure, so that the coolant can cool down the concave mould. 4.5.4 Convex mould and concave mould of closed molding station shall have a guide structure. The bilateral matching clearance should be controlled within 0.10 mm ~ 0.30 mm. 4.6 Selection of Equipment 4.6.1 Equipment’s force-stroke curve and energy shall satisfy the requirements of the force-stroke curve and deformation work of the molding of forgings. 4.6.2 Equipment precision shall comply with the relevant stipulations in GB/T 29532. 4.6.3 The selection of equipment shall consider the actual output demand for forgings, the load of the various stations, the allowable eccentric load and the cost of production, etc. 4.6.4 Equipment shall be equipped with material head and material tail automatic detection and rejection system. The requirements for the precision, stability and reliability of the mechanical arm transmission system; the efficiency of the cooling system for moulds; the internal cooling of moulds; the quick replacement of moulds and the reliability of the ejecting device shall be considered. 4.6.5 An automatic production line should be built, which mainly includes feed ......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.


      

Tips & Frequently Asked Questions

Question 1: How long will the true-PDF of English version of GB/T 37676-2019 be delivered?

Answer: The full copy PDF of English version of GB/T 37676-2019 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.

Question 2: Can I share the purchased PDF of GB/T 37676-2019_English with my colleagues?

Answer: Yes. The purchased PDF of GB/T 37676-2019_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.

Question 3: Does the price include tax/VAT?

Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countries

Question 4: Do you accept my currency other than USD?

Answer: Yes. www.ChineseStandard.us -- GB/T 37676-2019 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.

How to buy and download a true PDF of English version of GB/T 37676-2019?

A step-by-step guide to download PDF of GB/T 37676-2019_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 37676-2019".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3    Steps 4~6    Step 7    Step 8    Step 9