GB/T 1689-2014 PDF English
US$70.00 · In stock · Download in 9 secondsGB/T 1689-2014: Rubber vulcanized -- Determination of abrasion resistance (Akron machine) Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid GB/T 1689: Evolution and historical versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 1689-2014 | English | 70 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Rubber vulcanized -- Determination of abrasion resistance (Akron machine)
| Valid |
| GB/T 1689-1998 | English | 279 |
Add to Cart
|
3 days
|
Rubber vulcanized--Determination of abrasion resistance (Akron machine)
| Obsolete |
| GB 1689-1982 | English | 199 |
Add to Cart
|
2 days
|
Rubber, vulcanized--Determination of abrasion resistance (Akron machine)
| Obsolete |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 1689-2014
GB/T 1689-2014: Rubber vulcanized -- Determination of abrasion resistance (Akron machine)---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT1689-2014
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 83.060
G 40
Partially replacing GB/T 1689-1998
Rubber vulcanized - Determination of abrasion
resistance (Akron machine)
Issued on. SEPTEMBER 22, 2014
Implemented on. JUNE 01, 2015
Issued by. General Administration of Quality Supervision, Inspection and
Quarantine of PRC;
Standardization Administration of PRC.
Table of Contents
Foreword... 3
1 Scope... 5
2 Normative references... 5
3 Principle... 5
4 Instruments... 5
5 Instrument calibration... 6
6 Specimen... 6
7 Environment conditioning... 7
8 Procedures... 7
9 Test results... 7
10 Test report... 8
Appendix A (Normative) Standard rubber formula... 9
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
This standard replaces GB/T 1689-1998 Rubber vulcanized - Determination of
abrasion resistance (Akron machine). As compared with GB/T 1689-1998, the
main technical changes are as follows.
- DELETE the age number of the normative references (see Chapter 2;
Chapter 2 of the 1998 edition);
- DELETE the normative reference GB/T 9865.1-1996 (see Chapter 2 of the
1998 edition);
- ADD relevant content in the principle (see Chapter 3);
- ADD Akron machine (see 4.1);
- ADD content related to the balance (see 4.2);
- ADD recommendations for regular calibration of grinding wheels (see note
in Chapter 5);
- ADD the use of different sample preparation methods (see note in Chapter
6);
- CORRECT the unit of density in the calculation formula (see 9.1; 9.1 of
1998 edition).
This standard was proposed by the China Petroleum and Chemical Industry
Federation.
This standard shall be under the jurisdiction of the National Rubber and Rubber
Product Standardization Technical Committee General Test Method
Subcommittee (SAC/TC 35/SC 2).
Drafting organizations of this standard. Zhongce Rubber Group Co., Ltd.,
Triangle Tire Co., Ltd., Fengshen Tire Co., Ltd., Qingdao Rubber Conveyor Belt
Co., Ltd., Qingdao Yikesi New Materials Co., Ltd., Shandong Bayi Tire
Manufacturing Co., Ltd., Qingdao Double Star Group Technology Development
Center, Beijing Rubber Industry Research and Design Institute, Guizhou Tire
Co., Ltd., Jiangsu Xinzhengwei Testing Machinery Co., Ltd., Jiangsu Mingzhu
Testing Machinery Co., Ltd.
The main drafters of this standard. Xiang Chan, Xu Qiuhuan, Yan Fujiang, Ren
Shaowen, Liu Yuwan, Zhang Feng, Yao Feng, Lin Qingju, Wang Daiqiang, Liu
Qiang, Zhao Jianlin, Sha Shufen, Xie Junfang, Li Jing, Feng Ping, Shen Kehui,
Zhu Ming.
This standard replaces the standards previously issued as follows.
- GB/T 1689-1979, GB/T 1689-1982 (1989), GB/T 1689-1998.
Rubber vulcanized - Determination of abrasion
resistance (Akron machine)
1 Scope
This standard specifies the method for determining the abrasion resistance of
vulcanized rubber.
This standard is applicable to the determination of the abrasion resistance of
vulcanized rubber by the Akron machine.
2 Normative references
The following documents are indispensable for the application of this document.
For dated references, only the dated version applies to this document. For
undated references, the latest version (including all amendments) applies to
this document.
GB/T 533 Rubber vulcanized or thermoplastic - Determination of density
(GB/T 533-2008, ISO 2781.2007, IDT)
3 Principle
In this test, the specimen and the grinding wheel are rubbed under a certain
inclination angle and a certain load, to determine the wear volume or wear index
of a certain mileage of the specimen.
4 Instruments
4.1 Akron machine
4.1.1 The rotation speed of the rubber wheel shaft is 76 r/min ± 2 r/min. The
rotation speed of the grinding wheel shaft is 34 r/min ± 1 r/min.
4.1.2 When the angle between the rubber wheel shaft and the grinding wheel
shaft is zero degrees, the two shafts shall remain parallel and horizontal.
4.1.3 Add the test weight to the load bracket so that the specimen is subjected
to a load of 26.7 N ± 0.2 N.
4.1.6 The size of the test wheel is 150 mm in diameter, the center hole diameter
is 32 mm, the thickness is 25 mm; the abrasive material is alumina, the particle
size is 36, the binder is clay, the hardness is medium hardness 2.
4.2 Balance
Accurate to 0.001 g.
5 Instrument calibration
5.1 The angle between the rubber wheel shaft and the grinding wheel shaft as
well as the load on the specimen are important factors affecting the test results
and shall be calibrated periodically.
5.2 Adjust the test machine’s base to the horizontal state before calibration.
5.4 Install the load calibrator on the rubber wheel shaft. The right side of the
calibrator shall be close to the working surface of the grinding wheel. Place the
test weight and adjust the position of the balance weight, so that the load on
the specimen is 26.7 N ± 0.2 N.
6 Specimen
6.1 The specimen is strip-shaped with a length of (D + 2h) π mm, a width
of 12.7 mm ± 0.2 mm, a thickness of 3.2 mm ± 0.2 mm.
6.2 The surface of the specimen shall be flat and shall be free from cracks and
impurities.
6.3 After the two sides of the specimen are polished, they are glued to the
rubber wheel. The specimen shall not be subjected to tension when bonding.
The joint shall be smoothly transitioned during binding. The bonded sample
wheel shall be conditioned for at least 16 h.
6.4 The rubber wheel has a diameter of 68 mm, a thickness of 12.7 mm ±
0.2 mm, a hardness of 75 to 80 degrees (Shore A). The diameter of the center
hole shall correspond to the diameter of the rotary shaft of the rubber wheel.
7 Environment conditioning
The environment conditioning of the sample shall be carried out in accordance
with the provisions of GB/T 2941.
8 Procedures
8.1 Fix the glued specimen wheel on the rubber wheel shaft and start the motor
to rotate the specimen clockwise.
8.2 Pre-grind the specimen for 15 min ~ 20 min, remove the rubber scraps and
weigh the mass, accurate to 0.001 g.
8.4 Determine the density of the specimen according to GB/T 533.
9 Test results
9.1 The wear volume V of specimen is calculated according to formula (1).
9.2 The wear index A (%) of specimen, calculated according to formula (2).
10 Test report
The test report shall include the following.
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 1689-2014 be delivered?Answer: The full copy PDF of English version of GB/T 1689-2014 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 1689-2014_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 1689-2014_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 1689-2014 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. Question 5: Should I purchase the latest version GB/T 1689-2014?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 1689-2014 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. How to buy and download a true PDF of English version of GB/T 1689-2014?A step-by-step guide to download PDF of GB/T 1689-2014_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 1689-2014".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|