HG/T 2876-2009 (HG/T2876-2009, HGT 2876-2009, HGT2876-2009) & related versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | See Detail | Status | Similar PDF |
| HG/T 2876-2009 | English | 70 |
Add to Cart
|
0-9 seconds. Auto delivery.
|
Cellular material fo rubber-plastics shoes. Determination of compression set
|
HG/T 2876-2009
| Valid |
HGT 2876-2009
|
| HG/T 2876-1997 | English | 199 |
Add to Cart
|
2 days
|
Cellular material for rubber-plastics shoes-Determination of compression set
|
HG/T 2876-1997
| Obsolete |
HGT 2876-1997
|
Buy with any currencies (Euro, JPY, KRW...): HG/T 2876-2009 Preview this PDF: HG/T 2876-2009
HG/T 2876-2009
HG
CHEMICAL INDUSTRY STANDARD
OF THE PEOPLE’S REPUBLIC OF CHINA
ICS 61.060
Y 78
Registration number. 27277-2010
Replacing GB/T 2876-1997
Cellular material for rubber-plastics shoes -
Determination of compression set
ISSUED ON. DECEMBER 04, 2009
IMPLEMENTED ON. JUNE 01, 2010
Issued by. Ministry of Industry and Information Technology of PRC
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Terms and definitions ... 4
4 Principle ... 4
5 Test devices and instruments ... 5
6 Specimen ... 5
7 Conditioning of specimen and test environment ... 6
8 Test steps ... 6
9 Test results ... 6
10 Test report ... 7
Cellular material for rubber-plastics shoes -
Determination of compression set
1 Scope
This standard specifies the test method for the compressive set of cellular
material for rubber-plastics shoes.
This standard applies to the determination of compression set of cellular
material for rubber-plastics shoes.
2 Normative references
The provisions in following documents become the provisions of this standard
through reference in this standard. For the dated references, the subsequent
amendments (excluding corrections) or revisions do not apply to this standard;
however, parties who reach an agreement based on this standard are
encouraged to study if the latest versions of these documents are applicable.
For undated references, the latest edition of the referenced document applies.
GB/T 2941 Rubber - General procedures for preparing and conditioning test
pieces for physical test methods (GB/T 2941-2006, idt ISO 23529.2004)
3 Terms and definitions
The following terms and definitions apply to this standard.
3.1
Compression set
The rate of change of the geometrical dimension produced in the direction
of the force of the specimen after the external force which causes the
compressive deformation is completely removed.
4 Principle
The cellular material of rubber-plastics shoes is compressed by external force,
the material will deform along the direction of the force. When the external force
is removed, the material still cannot be restored to its original geometry. In the
The thickness is 10.0 mm ± 0.2 mm. Grind it according to the provisions of GB/T
2941. For the finished shoes, it may take sample from the cellular heel bottom.
6.2 If the thickness of the specimen is less than 10 mm, it may bond two layers.
After letting it be standing for 2 h, prepare it into a specimen. However, the test
results cannot be compared with the test results of the standard specimen.
6.3 The surface of the specimen shall be flat and shall not be left with a
patterned or dense skin. The compressed surface is consistent with the
compression surface of the finished shoe when it is in use.
7 Conditioning of specimen and test environment
7.1 The storage of samples and specimens shall be carried out in accordance
with the provisions of GB/T 2941.
7.2 The test shall be carried out under the standard temperature and humidity
of the laboratory in accordance with the provisions of GB/T 2941.
8 Test steps
8.1 Number the specimen. Measure the geometry of the specimen.
8.2 Use a vernier caliper to measure the length and width of the specimen,
accurate to 0.02 mm.
8.3 Use a thickness gauge to measure the height before and after compression
of the specimen, accurate to 0.01 m.
8.4 The number of specimens for each sample shall be not less than three. The
height of the same set of specimens shall not differ by more than 0.1 mm.
8.5 Place the specimen in the fixture. Tighten the nut to the ring stopper. The
specimens shall have sufficient spacing in the fixture, so that the specimens do
not come into contact with one another when compressed.
8.6 The compression time is 72 h ± 2 h. Take out the specimen after reaching
the time. Let it be standing for 2 h. Then measure the height of specimen after
restoration.
9 Test results
The compression set of the specimen is calculated by the following formula.
......
| Standard ID | HG/T 2876-2009 (HG/T2876-2009) | | Description (Translated English) | Cellular material fo rubber-plastics shoes. Determination of compression set | | Sector / Industry | Chemical Industry Industry Standard (Recommended) | | Classification of Chinese Standard | Y78 | | Classification of International Standard | 61.060 | | Word Count Estimation | 6,691 | | Date of Issue | 2009-12-04 | | Date of Implementation | 2010-06-01 | | Older Standard (superseded by this standard) | HG/T 2876-1997 | | Quoted Standard | GB/T 2941 | | Drafting Organization | Shanghai Quality Inspection and Technical Research | | Administrative Organization | National Rubber and rubber products Standardization Technical Committee Technical Committee shoes | | Regulation (derived from) | Engineering (2009) No. 66; industry standard filing Notice 2010 No. 2 (No. 122 overall) | | Summary | This standard specifies the rubber shoes microporous material compression deformation test methods. This standard applies to rubber shoes microporous materials Determination of compressive deformation. | | Standard ID | HG/T 2876-1997 (HG/T2876-1997) | | Description (Translated English) | Cellular material for rubber-plastics shoes-Determination of compression set | | Sector / Industry | Chemical Industry Industry Standard (Recommended) | | Classification of Chinese Standard | Y78 | | Classification of International Standard | 61.06 | | Word Count Estimation | 4,425 | | Date of Issue | 1997/4/21 | | Date of Implementation | 1997/10/1 | | Older Standard (superseded by this standard) | GB 4495-1984 | | Quoted Standard | GB 2941-1991; HG/T 2198-1991 | | Regulation (derived from) | Industry-Science (2009) No. 66; Industry Standard Filing Notice 2010 No. 2 (Overall No. 122) |
|