GB/T 24525-2009 (GB/T24525-2009, GBT 24525-2009, GBT24525-2009) & related versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | See Detail | Status | Similar PDF |
| GB/T 24525-2009 | English | 90 |
Add to Cart
|
0-9 seconds. Auto delivery.
|
Method for determination of specific resistance of carbon materials
|
GB/T 24525-2009
| Valid |
GBT 24525-2009
|
Buy with any currencies (Euro, JPY, KRW...): GB/T 24525-2009 Preview this PDF: GB/T 24525-2009
GB/T 24525-2009
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 29.050
Q 52
Method for Determination of
Specific Resistance of Carbon Materials
ISSUED ON. OCTOBER 30, 2009
IMPLEMENTED ON. MAY 1, 2010
Issued by. General Administration of Quality Supervision, Inspection and
Quarantine;
Standardization Administration of PRC.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative References ... 4
3 Principle ... 4
4 Determination of Test Body in Lab ... 5
5 On-Site Determination of Graphite Electrode Products ... 7
6 Allowable Error ... 9
7 Test Report ... 9
Foreword
This Standard was proposed by China Iron and Steel Association.
This Standard shall be under the jurisdiction of National Technical Committee for
Standardization of Steel.
Drafting organizations of this Standard. Sinosteel Jilin Carbon Co., Ltd., and China
Metallurgical Information and Standardization Research Institute.
Chief drafting staffs of this Standard. Wang Jun, Guo Rongyao, Kang Jian, and Cui
Guowei.
Method for Determination of
Specific Resistance of Carbon Materials
1 Scope
This Standard specifies the principle, apparatus, test procedures and allowable error
for the determination of specific resistance of carbon materials.
This Standard is applicable to the determination of specific resistance of carbon
products and graphite products at room temperature.
2 Normative References
The provisions in following documents become the provisions of this Standard through
reference in this Standard. For dated references, the subsequent amendments
(excluding corrigendum) or revisions do not apply to this Standard, however, parties
who reach an agreement based on this Standard are encouraged to study if the latest
versions of these documents are applicable. For undated references, the latest edition
of the referenced document applies.
GB/T 1427 Sample Method of Carbon Material
GB/T 8170 Rules of Rounding off for Numerical Values & Expression and
Judgement of Limiting Values
3 Principle
The specific resistance represents a property of the material, which is the amount of
resistance when current passing the material. It numerically equals to the resistance
value of the conductor with length (L) of 1m and sectional area (S) of 1m2, which is
expressed by ρ. The following formula can be obtained as per Ohm’s Law and the
characteristics of the conductor.
Where.
ρ – Specific resistance of conductor, in µΩm;
Figure 3 Diagram of Testing System of Specific Resistance Tester
5.3.4 Clamp the test body on the test bench; press the current button, so that current
passes the extrusion axial of test body, then read the specific resistance value.
5.3.5 When measuring the current, the test body temperature may raise; therefore,
the measuring time is required to be as short as possible (not exceed 1 min); current
density is lower than 1 A/cm2; so that the change of specific resistance caused by heat
is no more than ±0.5%.
6 Allowable Error
The allowable error when measuring the specific resistance of carbon materials shall
be 2%.
7 Test Report
The test report shall contain the following contents.
a) Entrusting organization;
b) Specimen number, name and specification;
c) Individual and average value of the test result;
d) Potential contact spacing;
e) Current value at the time of measurement;
f) Testing organization;
g) Auditors;
h) Test date.
......
| Standard ID | GB/T 24525-2009 (GB/T24525-2009) | | Description (Translated English) | Method for determination of spcific resistance of carbon materials | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | Q52 | | Classification of International Standard | 29.050 | | Word Count Estimation | 7,789 | | Date of Issue | 2009-10-30 | | Date of Implementation | 2010-05-01 | | Quoted Standard | GB/T 1427; GB/T 8170 | | Drafting Organization | Sinosteel Jilin Carbon Co., Ltd. | | Administrative Organization | National Steel Standardization Technical Committee | | Regulation (derived from) | National Standard Approval Announcement 2009 No.12 (Total No.152) | | Proposing organization | China Iron and Steel Association | | Issuing agency(ies) | Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China; Standardization Administration of China | | Summary | This standard specifies the principles for determination of the resistance of carbon materials, equipment, test procedure, allow errors. This standard applies to the determination of carbon products and graphite products under normal temperature resistivity. |
|