GB/T 10595-2017 (GB/T10595-2017, GBT 10595-2017, GBT10595-2017) & related versions
Buy with any currencies (Euro, JPY, KRW...): GB/T 10595-2017 Preview this PDF: GB/T 10595-2017
GB/T 10595-2017
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 53.040.10
J 81
Replacing GB/T 10595-2009
Belt Conveyors
ISSUED ON: DECEMBER 29, 2017
IMPLEMENTED ON: JULY 1, 2018
Issued by: General Administration of Quality Supervision, Inspection and
Quarantine of the People’s Republic of China;
Standardization Administration of the People’s Republic of China.
Table of Contents
Foreword ... 3
1 Scope ... 7
2 Normative References ... 7
3 Type and Basic Parameters ... 10
4 Technical Requirements ... 15
5 Test Methods ... 25
6 Inspection Rules ... 37
7 Marking, Packaging and Storage ... 38
Appendix A (normative) Flaw Detection Method for Pulley ... 41
Belt Conveyors
1 Scope
This Standard specifies the type and basic parameters, technical requirements, test methods,
inspection rules, marking, packaging and storage of belt conveyors (hereinafter referred to as
the conveyors).
This Standard is applicable to conveyors conveying bulk materials and finished articles.
For conveyors conveying toxic, harmful, flammable, explosive, highly corrosive and
radioactive materials, and conveyors with special requirements and types, the general parts may
also be taken as a reference.
2 Normative References
The following documents are indispensable to the application of this document. In terms of
references with a specified date, only versions with a specified date are applicable to this
document. In terms of references without a specified date, the latest version (including all the
modifications) is applicable to this document.
GB/T 191 Packaging - Pictorial Marking for Handling of Goods (GB/T 191-2008, ISO
780:1997, MOD)
GB/T 226 Test Method for Macrostructure and Defect of Steel by Etching
GB/T 700 Carbon Structural Steels
GB/T 985.1 Recommended Joint Preparation for Gas Welding, Manual Metal Arc Welding,
Gas-shield Arc Welding and Beam Welding
GB/T 985.2 Recommended Joint Preparation for Submerged Arc Welding
GB/T 1184 Geometrical Tolerancing - Geometrical Tolerance for Features without Individual
Tolerance Indications (GB/T 1184-1996, eqv ISO 2768-2:1989)
GB/T 1979 Standard Diagrams for Macrostructure and Defect of Structural Steels
GB/T 2828.1 Sampling Procedures for Inspection by Attributes - Part 1: Sampling Schemes
Indexed by Acceptance Quality Limit (AQL) for Lot-by-lot Inspection
GB/T 3323 Radiographic Examination of Fusion Welded Joints in Metallic Materials
GB/T 3767 Acoustics - Determination of Sound Power Levels and Sound Energy Levels of
Noise Sources Using Sound Pressure - Engineering Methods for an Essentially Free Field over
a Reflecting Plane (GB/T 3767-2016, ISO 3744:2010, IDT)
GB/T 4053 Safety Requirements for Fixed Steel Ladders and Platform
GB/T 4323 Pin Coupling with Elastic Sleeve
GB/T 4490 Conveyor Belts with Textile Carcass - Widths and Lengths
GB/T 5014 Pin Coupling Elastomer
GB/T 5015 Gear Coupling with Pin Elastomer
GB/T 5272 Coupling with Elastic Spider
GB/T 6069 Roller Chain Coupling
GB/T 6402 Steel Forgings - Method for Ultrasonic Testing
GB/T 7233.1-2009 Steel Castings - Ultrasonic Examination - Part 1: Steel Castings for General
Purposes
GB/T 7324 General Purpose Lithium Lubricating Grease
GB/T 7984 Conveyor Belt of Textile Construction for General Use
GB/T 8923.1 Preparation of Steel Substrates before Application of Paints and Related Products
- Visual Assessment of Surface Cleanliness - Part 1: Rust Grades and Preparation Grades of
Uncoated Steel Substrates and of Steel Substrates after Overall Removal of Previous Coatings
GB/T 9239.1 Mechanical Vibration - Balance Quality Requirements for Rotors in a Constant
(rigid) State - Part 1: Specification and Verification of Balance Tolerances
GB/T 9286 Paints and Varnishes - Cross-cut Test
GB/T 9443 Steel and Iron Castings - Liquid Penetrant Inspection
GB/T 9770 Steel Cord Conveyor Belts for General Use
GB/T 11345 Non-destructive Testing of Welds - Ultrasonic Testing - Techniques, Testing Levels,
and Assessment
GB/T 11352 Carbon Steel Castings for General Engineering Purpose
GB/T 13306 Plate
GB/T 13384 General Specifications for Packing of Mechanical and Electrical Product
GB/T 13793 Straight Seam Welded Steel Pipe
comply with the stipulations of Grade-9 precision in GB/T 1184.
4.3.3 The backstop shall comply with the stipulations of JB/T 9015. After the backstop is
installed, when the conveyor is in operation, the backstop shall flexibly operate; when the
conveyor is in the backstop state, the backstop shall be safe and reliable.
4.3.4 After the elastic coupling is assembled, it shall comply with the stipulations of GB/T 4323,
GB/T 5014, GB/T 5015 and GB/T 5272.
4.3.5 After the curved tooth coupling is assembled, it shall comply with the stipulations of GB/T
26103.1, GB/T 26103.3, GB/T 26103.4 and GB/T 26103.5.
4.3.6 After the steelflex coupling is assembled, it shall comply with the stipulations of JB/T
8869.
4.3.7 After the roller chain coupling is assembled, it shall comply with the stipulations of JB/T
6069.
4.3.8 After the electro-hydraulic drum brakes are assembled, they shall comply with the
stipulations of JB/T 6406.
4.3.9 The caliper-type electro-hydraulic disc brakes shall comply with the stipulations of JB/T
7020. During braking, the working contact area between the brake block and the brake disc
shall not be less than 80%.
4.3.10 When fluid coupling is adopted for the high-speed shaft, it shall comply with the
stipulations of JB/T 9000.
4.3.11 Motorized driving pulley shall comply with the stipulations of JB/T 7330.
4.3.12 The speed reducers for the conveyors shall comply with the requirements for starting
with full load.
4.4 Steel Castings for the Conveyors
4.4.1 The carbon steel castings shall comply with the stipulations of GB/T 11352. Large-sized
low-alloy steel castings shall comply with the stipulations of JB/T 6402.
4.4.2 The sticky sand, sand inclusions, flashes, burrs, casting heads and oxide scales on the
surface of the castings shall be eliminated, and there shall be no cracks, cold insulation,
shrinkages, slag inclusions or pores that may affect the performance of the castings.
4.4.3 The non-destructive testing of the steel castings shall comply with the stipulations of JB/T
5000.14.
4.5 Steel Forgings for the Conveyors
4.5.1 The forgings shall not manifest any cracks, folds, interlayers, white spots or residual
shrinkage cavities.
4.5.2 The ultrasonic testing shall comply with the stipulations of GB/T 6402, GB/T 226 and
GB/T 1979.
4.5.3 The acceptance inspection rules and test methods of the forgings shall comply with the
stipulations of JB/T 5000.8.
4.6 Pulley
4.6.1 The minimum wall thickness b1 of the pulley body shall comply with the stipulations of
Formula (1).
4.6.2 In addition to satisfying the above-mentioned requirements of 4.4.2, the pulley steel
casting plates shall also be subjected to the surface and internal inspections.
The external quality shall comply with the requirements of penetrant inspection in GB/T 9443;
the surface quality shall be “smooth”; the inspection quality level shall be Level-2.
The internal quality shall comply with the requirements of GB/T 7233.1; the preparation of the
surface for the ultrasonic testing of steel castings shall comply with the requirements of 5.4 in
GB/T 7233.1-2009. The ready-to-weld area and special outer layers shall comply with the
requirements of quality level 1 in Table 1 of GB/T 7233.1-2009; the overall non-destructive
testing method for the pulley is shown in Appendix A.
4.6.3 The quality classification limit of the defects of the pulley body and the welding seam of
the plate shall comply with the requirements of Level-B in GB/T 19418. When ultrasonic testing
is adopted, the inspection level shall not be lower than Level-B in GB/T 11345; the acceptance
inspection level shall comply with the requirements of Level-2 in GB/T 29712. Alternatively,
when radiographic inspection is adopted, its quality level shall not be lower than the
requirements of Level-2 in GB/T 3323.
4.6.4 The internal stress of the pulley body with the resultant force greater than 80 kN shall be
eliminated.
4.6.5 The diameter deviation of the outer circle of the pulley shall comply with the stipulations
of Table 8.
the centerline of the conveyor frame shall not be greater than 3.0 mm.
4.12.6 The coaxiality between the axis of the drive pulley and the axis of the low-speed shaft
of the speed reducer shall comply with the stipulations of the coupling used.
4.12.7 The parallelism of the axes of the two drive pulleys on the same frame shall not be greater
than 0.4 mm.
4.12.8 The upper surface of the idler (except the self-aligning roller and the transition roller)
shall be located on the same plane (horizontal or inclined surface), or on the arc surface of a
common radius (the idler on the concave arc section or the convex arc section of the conveyor).
The height difference among the upper surfaces of the three adjacent sets of idler rollers shall
not exceed 2.0 mm.
4.12.9 The working surfaces of the rails shall be within the same plane, and the elevation
difference of the rail top of each section of the rail shall not exceed 2.0 mm. The straightness
limit of the rail is 1.0 mm within the length of 1 m, 4.0 mm within the length of 25 m and 15
mm within the full length. The height difference of the working surface at the rail joint shall
not exceed 0.5 mm. The gap of the rail joints shall not be greater than 3.0 mm. The gauge
deviation shall not be greater than 2.0 mm.
4.12.10 The perpendicularity of the weight guide frame of the vertical weight tensioning device
to the horizontal plane is 1/1,000 of the length of the axis of the tensioning pulley.
4.12.11 The wheel treads of the take-up car shall be on the same plane, and the flatness limit is
2.0 mm.
4.12.12 After the assembly of the take-up car, the inner and outer declination angles of the
tensioning steel rope and the centerline of the pulley rope groove and the vertical line of the
reel shaft shall be less than 6.
4.12.13 After the cleaner is installed, the contact length between its scraper or brush and the
conveyor belt in the direction of the pulley axis shall not be less than 85%.
4.12.14 The connection joint of the conveyor belt shall be flat and straight, and the straightness
on the 10 m length with the joint as the center shall not be greater than 15 mm.
5 Test Methods
5.1 Visual Inspection
Visual inspection includes whether the working condition of the whole machine and all
important parts satisfies the requirements, and whether the appearance quality, safety signs and
plates satisfy the technical requirements.
5.2 Dynamic Rotation Resistance Test of Idler Roller
5.15 Testing of Paint Film Adhesion
The measurement method for paint film adhesion shall comply with the requirements of GB/T
9286.
6 Inspection Rules
6.1 General
The inspection of the conveyors is divided into exit-factory inspection and type inspection.
6.2 Exit-factory Inspection
Each conveyor can only be allowed to exit the factory after passing the inspection. See Table
19 for the exit-factory inspection items.
6.3 Type Inspection
6.3.1 Under one of the following circumstances, type inspection shall be carried out:
a) Trial-type appraisal of new products or old products transferred to another factory for
production;
b) After formal production, when there are major changes in structure, materials and
processes that may affect product performance;
c) When production is resumed after being suspended for more than one year;
d) When there are major differences between the exit-factory inspection results and the
previous type inspection;
e) When the national quality supervision and inspection institution puts forward a
request for the type inspection.
6.3.2 The type inspection items are shown in Table 19.
7.1.1 Each conveyor shall have a product plate fixed at a prominent position on any head frame
where the drive pulley is installed, and the plate shall at least include the following contents:
a) product name;
b) model;
c) main technical parameters (belt breadth, belt speed, conveying capacity and installed
power);
d) date of manufacture (serial No.);
e) name of the manufacturer.
7.1.2 The sizes and technical requirements of the plate shall comply with the stipulations of
GB/T 13306.
7.2 Packaging
7.2.1 Basic requirements
The packaging of the conveyors shall comply with the stipulations of GB/T 13384. The pictorial
marking for handling of goods shall comply with the relevant stipulations of GB/T 191.
7.2.2 Packaging of parts
When placing the parts of the conveyors in the box, the center of gravity shall be as centered
and lower as possible. If the center of gravity is obviously high, corresponding balancing
measures shall be taken.
7.2.3 Idler
All idler rollers shall be packaged to prevent bumping; the brackets are allowed to be bundled
and shipped naked.
7.2.4 Pulley
Anti-rust and protective measures shall be taken on the shaft head of the drive pulley. Protective
measures shall be taken on the surface of the pulley. When the pulleys are separately shipped,
measures shall be taken to prevent the pulleys from rolling.
7.2.5 Tensioning device
7.2.5.1 The screw tensioning device (including the bend pulley) is installed on the frame for
shipment.
7.2.5.2 Wire ropes, rope clips, bend pulleys and long screws of the tensioning device are packed
in a box for shipment.
method, and if necessary, the transverse wave method can be adopted to facilitate the
determination.
A.2.1.3 For intensive defects, the diameter of 6 mm flat-bottomed hole shall be taken as the
quantitative sensitivity, and the half-wave height method shall be adopted for detection.
A.2.1.4 Within the 50 mm width of the welded end, the dense pores and inclusions shall be less
than 20% of the wall thickness. Detection can be performed from the outer circular surface with
a dual element probe.
A.2.2 Non-destructive testing method for butt longitudinal welds and annular welds of
pulley body
A.2.2.1 During radiographic inspection, the amount of each weld being inspected shall not be
less than 20% of the weld length. Ultrasonic inspection shall be carried out in the full range.
A.2.2.2 The non-destructive testing method shall comply with the stipulations of GB/T 3323 or
GB/T 11345.
A.2.3 Non-destructive testing method for annular fillet welds of pulley body and receiving
plate
A.2.3.1 Along the circumference direction of the pulley body and at an adjacent interval of 90,
perform the non-destructive testing on 4 welds with a length of not less than 100 mm. If one of
the welds is disqualified, then, 100% non-destructive testing shall be performed.
A.2.3.2 Use the vertical detection method with a straight probe; at “▽”, the detection depth is
slightly greater than a, as it is shown in Figure A.2:
......
GB/T 10595-2009
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 53.040.10
J 81
Replacing GB/T 987-1991, GB/T 988-1991, GB/T 990-1991 and GB/T 10595-1989
Belt Conveyors
ISSUED ON. APRIL 2, 2009
IMPLEMENTED ON. NOVEMBER 01, 2009
Issued by. General Administration of Quality Supervision, Inspection
and Quarantine of the People’s Republic of China;
Standardization Administration of the People’s Republic of
China.
Table of Contents
Foreword ... 3
1 Scope ... 5
2 Normative Reference ... 5
3 Basic parameters ... 7
4 Technical Requirements ... 9
5 Test Methods ... 18
6 Inspection rules ... 26
7 Mark, packing and storage ... 27
Appendix A ... 30
Foreword
This Standard replaces GB/T 987-1991 “Belt Conveyors - Basic Parameters and
Dimensions”, GB/T 988-1991 “Belt Conveyor Pulleys - Basic Parameters and
Dimensions”, GB/T 990-1991 “Belt Conveyor Idlers - Basic Parameters and
Dimensions” and GB/T 10595-1989 “General Specification for Belt Conveyors”.
Compared with GB/T 987-1991, GB/T 988-1991, GB/T 990-1991 and GB/T
10595-1989, the main changes of this Standard are as follows.
- ADD technical requirements of the packing of belt conveyors;
- ADD requirements of the designed life of roller shaft;
- ADD requirements of belt conveyors;
- ADD property test for the surface rubber and bottom rubber of rubber-covered
rollers;
- ADD requirements and determination of conveying capacity;
- MODIFY the premises for dustproof and waterproof property of idler rollers;
- RE-SPECIFY the physical and mechanical properties of surface rubber;
- MODIFY requirements for the fault detection quality of roller shaft;
- SUPPLEMENT the static balancing test method for roller;
- MODIFY the linearity of conveyor belt;
- MODIFY the service life of idler rollers;
- MODIFY the radial circular run-out of the idler rollers’ top circle;
- MODIFY the test method for the rotation resistance of idler rollers;
- MODIFY the rotating speed in the dustproof and waterproof test of rollers.
Appendix A of this Standard is normative.
This Standard was proposed by China Machinery Industry Federation.
This Standard shall be under the jurisdiction of National Technical Committee on
Continuous Mechanical Handling Equipment of Standardization Administration of
China.
Responsible drafting organization of this Standard. Beijing Elevating Machinery
Institute.
Participating drafting organizations of this Standard. Sichuan Zigong Conveying
Machine Co., Ltd, Shenyang Mining Machinery (Group) Co., Ltd, Beijing Yueji Tongli
Machinery Manufacturing Co., Ltd, Hengyang Hoisting and Conveying Machinery Co.,
Ltd, Tongling Miracle Mechanical Equipment Co., Ltd, Shandong Shankuang
Machinery Co., Ltd, Tangshan Mining & Metallurgical Machinery Plant, Jiaozuo
Creation Machinery Co., Ltd, Shanghai Qingpu Lifting Transport C., Ltd, Anhui
Pandeng Machinery joint Stock Co., Ltd, Conveying Machinery Equipment
Manufacturing Company of Magang Corporation, Dongguan Loti Industrial Co., Ltd.
The main drafters of this Standard. Zhang Zunjing, Zhang Qiang, Huang Wenlin, Yang
MInghua, Gong Xinrong, Huang Xiliang, Zhang Xiaohua, Zhou Shichang, Yu
Chuncheng, Meng Fanbo, Hou Tiancheng, Li Ping, Li Tianguo, Zhang Yong.
The historical versions replaced by this Standard are as follows.
- GB 987-1967, GB 987-1977, GB/T 987-1991;
- GB 988-1967, GB 988-1977, GB/T 988-1991;
- GB 989-1967, GB 989-1977;
- GB 990-1967, GB 990-1977, GB/T 990-1991;
- GB 991-1967, GB 991-1977;
- GB 992-1967, GB 992-1977;
- GB 993-1967, GB 993-1977;
- GB 994-1967, GB 994-1977;
- GB 995-1967, GB 995-1977;
- GB 996-1967, GB 996-1977;
- GB/T 10595-1989.
Belt Conveyors
1 Scope
This Standard specifies the technical requirements, test methods, test rules, mark,
packaging and storage of the belt conveyor (hereafter referred to as conveyor).
This Standard is applicable to the transportation of different kinds of massive, granular
bulk materials and conveyors.
For conveyors with special requirements and patterns, the general part shall also be
referred to.
2 Normative Reference
The provisions in following documents become the provisions of this Standard through
reference in this Standard. For dated references, the subsequent amendments
(excluding corrections) or revisions do not apply to this Standard, however, parties
who reach an agreement based on this Standard are encouraged to study if the latest
versions of these documents are applicable. For undated references, the latest edition
of the referenced document applies.
GB/T 191 Pictorial marking for handling of goods (GB 191-2008, ISO 780.1997,
MOD)
GB/T 528 Rubber, Vulcanized or thermoplastic - Determination of tensile
stress-strain properties (GB/T 528-1998, eqv ISO 37.1994)
GB/T 531 Rubber - Determination of indentation hardness by means of pocket
hardness meters
GB/T 985 Basic Forms and sizes of weld grooves for gas welding, manual arc
welding and gas-shielded arc welding
GB/T 986 Basic Forms and sizes of submerged arc weld grooves
GB/T 1184-1996 Geometrical tolerancing - Geometrical tolerances for features
without individual tolerance indications
GB/T 2828.1-2003 Sampling procedures for inspection by attributes - Part 1.
sampling scheme indexed by acceptance quality limit (AQL) for lot-by-lot
inspection (ISO 2859-1.1999, IDT)
GB/T 3323-2005 Radiographic examination of fusion welded joints in metallic
materials
GB/T 3512 Rubber, Vulcanized or thermoplastic - Accelerated ageing and heat
resistance tests-air-oven method
GB/T 3767-1996 Acoustics - Determination of sound power levels of noise sources
using sound pressure - Engineering method in an essentially free field over a
reflecting plane (eqv ISO 3744.1994)
GB/T 4323 Pin coupling with elastic sleeve
GB/T 4490 Conveyor belts - Dimensions
GB/T 5014 Elastic pin coupling
GB/T 5015 Gear coupling with elastic pin
GB/T 5272 Coupling with elastic spider
GB/T 6402 Steel forgings - Method for ultrasonic examination
GB/T 7324-1994 General purpose lithium lubricating grease
GB/T 7984 Conveyor belts - Specification for rubber or plastics covered conveyor
belts of textile construction for general use
GB/T 8923-1988 Rusting rating and derusting rating of steel surface before
application (eqv ISO 8501-1.1988)
GB/T 9239.1-2006 Mechanical vibration - Balance quality requirements for rotors in
a constant (rigid) state - Part 1. Specification and verification of balance tolerances
GB/T 9286-1998 Paints and varnishes - Cross cut test for films (eqv ISO
2409.1992)
GB/T 9770 Steel cord conveyor belts for general use
GB/T 9867 Rubber - Determination of abrasion resistance
GB 11211 Rubber vulcanized - Determination of adhesion to metal - Tension
method
GB/T 11345-1989 Method for manual ultrasonic testing and classification of testing
results for ferritic steel welds
GB/T 13306 Nameplate
GB/T 13384 General specifications for packing of mechanical and electrical
product
GB/T 13792 Welded steel pipe for supporting roller of belt conveyor
GB 14784 Safety regulations of belt conveyor
JB/T 6406 Electro-hydraulic drum brakes
JB/T 7020 Electro-hydraulic disc brakes
JB/T 7330 Motorized pulley
JB/T 8869 Steel flex couplings
JB/T 9000 Fluid couplings - General specification
JB/T 9002 Gearboxes for transportation machinery
JB/T 10064 General technical specifications for A-type pulse-echo supersonic flaw
detector
3 Basic parameters
3.1 Belt width
The belt width of the conveyor shall meet the requirements of Table 1.
Table 1 mm
Belt width 300, 400, 500, 650, 800, 1000, 1200, 1400, 1600, 1800, 2000, 2200, 2600, 2800
3.2 Nominal belt speed
The nominal belt speed of the conveyor shall meet the requirements of Table 2.
Table 2 mm/s
Nominal belt speed 0.2, 0.25 0.315, 0.4, 0.5, 0.63, 0.8, 1.0, 1.25, 1.6, 2.0, 2.5, 3.15, 3.55, 4.0, 4.5, 5.0, 5.6, 6.3, 7.1
3.3 Roller
3.3.1 The roller diameter of the conveyor shall meet the requirements of Table 3.
Table 3 mm
Roller diameter 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1400, 1600, 1800
4.3.1 The driving device shall not have oil leakage.
4.3.2 After brake wheel in installed, the ex-circle radial circular run-out shall comply
with the level-9 precision in GB/T 1184-1996.
4.3.3 After backstop is installed, the conveyor shall run smoothly; in backstop state, it
shall be reliably and safely.
4.3.4 The installation of the elastic coupling shall comply with the requirements of
GB/T 4323, GB/T 5014, GB/T 5015 and GB/T 5272.
4.3.5 Radial displacement of the Oldham coupling shall be not more than 1.0 mm; the
angle between two axes shall be not more than 0°30’.
4.3.6 The installed serpentine coupling shall comply with the requirements of JB/T
8869.
4.3.7 Surface run-out and radial run-out of the chain coupling shall be 0.10 mm.
4...
......
| Standard ID | GB/T 10595-2017 (GB/T10595-2017) | | Description (Translated English) | Belt conveyors | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | J81 | | Classification of International Standard | 53.040.10 | | Word Count Estimation | 30,395 | | Date of Issue | 2017-12-29 | | Date of Implementation | 2018-07-01 | | Drafting Organization | Beijing Hoisting and Transport Machinery Design and Research Institute | | Administrative Organization | National Continuous Handling Machinery Standardization Technical Committee (SAC/TC 331) | | Proposing organization | China Machinery Industry Federation | | Issuing agency(ies) | People's Republic of China General Administration of Quality Supervision, Inspection and Quarantine, China National Standardization Administration | | Standard ID | GB/T 10595-2009 (GB/T10595-2009) | | Description (Translated English) | Belt conveyors | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | J81 | | Classification of International Standard | 53.040.10 | | Word Count Estimation | 24,282 | | Date of Issue | 2009-04-02 | | Date of Implementation | 2009-11-01 | | Older Standard (superseded by this standard) | GB/T 10595-1989; GB/T 987-1991; GB/T 988-1991; GB/T 990-1991 | | Quoted Standard | GB/T 191; GB/T 528; GB/T 531; GB/T 985; GB/T 986; GB/T 1184-1996; GB/T 4323; GB/T 4490; GB/T 5014; GB/T 5015; GB/T 5272; GB/T 6402; GB 7324-1994; GB/T 7984; GB/T 8923-1988; GB/T 9239.1-2006; GB/T 9286-1998; GB/T 9770; GB/T 9867; GB/T 11211; GB/T 11345-1989; GB/T 13306; GB/T 13384; GB/T 13792; GB/T 14784; JB/T 6406; JB/T 7020; JB/T 7330; JB/T 8869; JB/T 9000; JB/T 9002 | | Drafting Organization | Beijing Institute of lifting the transport machinery | | Administrative Organization | Continuous mechanical handling National Standardization Technical Committee | | Regulation (derived from) | National Standard Approval Announcement 2009 No.4 (Total No.144) | | Proposing organization | China Machinery Industry Federation | | Issuing agency(ies) | Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China; Standardization Administration of China | | Summary | This standard specifies the conveyor (hereinafter referred to as the conveyor) of the basic parameters, technical requirements, test methods, inspection rules, signs, packaging and storage. This standard applies to all kinds of things to send bulk, granular materials and other loose objects into items of the sending machine. There are special requirements and special types of pumping machines. It can also refer to the use of common parts. | | Standard ID | GB/T 10595-1989 (GB/T10595-1989) | | Description (Translated English) | General specification for belt conveyors | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | J81 | | Classification of International Standard | 53.040.10 | | Word Count Estimation | 18,144 | | Date of Issue | 1989/3/22 | | Date of Implementation | 1990/1/1 | | Older Standard (superseded by this standard) | JB 818-1984 | | Quoted Standard | GB 1184; GB/T 2828; GB/T 3323; GB 3767; GB 3836.1; GB/T 4323; GB 5014; GB 5015; GB/T 5272; GB/T 5677; GB/T 6333; GB/T 6402; GB 985; GB 986; GB 987��996; JB 1152; JB 2647; JB 3001; JB 3668; JB 8; ZB J19 009; ZB Y 230 | | Regulation (derived from) | Announcement of Newly Approved National Standards 2009 No. 4 (No. 144 overall) |
|