GB/T 26949.11-2016 PDF EnglishUS$150.00 · In stock · Download in 9 seconds
GB/T 26949.11-2016: Industrial trucks -- Verification of stability -- Part 11: Industrial variable-reach trucks Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 26949.11-2016: Industrial trucks -- Verification of stability -- Part 11: Industrial variable-reach trucks---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT26949.11-2016 Industrial trucks--Verification of stability--Part 11. Industrial variable-reach trucks ICS 53.060 J83 National Standards of People's Republic of China Industrial vehicle stability verification Part 11. Telescopic forklift (ISO 22915-11.2011, IDT) Released on October 13,.2016 2017-05-01 implementation General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China China National Standardization Administration issued ForewordGB/T 26949 "Industrial Vehicle Stability Verification" has or plans to release the following parts. --- Part 1. General; ---Part 2. Counterbalanced forklift; --- Part 3. Forward and legged forklifts; --- Part 4. Pallet stacker, double stacker and picker with a height of not more than 1200mm from the operator; --- Part 5. Side forklifts (one side); --- Part 7. Two-way and multi-directional operation of the forklift; --- Part 8. Additional stability tests for stacking operations under gantry forward and load lift conditions; ---Part 9. Counterbalanced forklifts carrying freight containers of 6m and longer lengths; --- Part 10. Additional stability tests for stacking operations under lateral load conditions of power units; --- Part 11. Telescopic forklift; --- Part 12. Telescopic forklifts carrying freight containers of 6 m or longer in length; --- Part 13. Off-road forklifts with gantry; --- Part 14. Off-road telescopic forklift; --- Part 15. Counterbalanced forklifts with articulated steering; --- Part 16. Walker vehicles; --- Part 17. Cargo and personnel carriers; --- Part 20. Additional stability tests for operation under load bias conditions; --- Part 21. Picking vehicles with an operator position elevation greater than 1200 mm; --- Part 22. Three-way stacker forklifts with or without operator position. This part is the 11th part of GB/T 26949. This part is drafted in accordance with the rules given in GB/T 1.1-2009. This section uses the translation method equivalent to ISO 22915-11.2011 "Industrial Vehicle Stability Verification Part 11. Telescopic Arms car". The documents of our country that have a consistent correspondence with the international documents referenced in this part are as follows. ---GB/T 6104-2005 Mobile Industrial Vehicle Terminology (ISO 5053.1987, IDT) --- GB/T 26949.1-2012 Industrial vehicle stability verification Part 1. General (ISO 22915-1.2008, IDT) This section has made the following editorial changes. --- Original Table 1 "The position of the vehicle on the inclined platform (Test 5) in the articulated frame 4.2.3b)" is incorrect and corrected. This part was proposed by the China Machinery Industry Federation. This part is under the jurisdiction of the National Industrial Vehicle Standardization Technical Committee (SAC/TC332). This section is responsible for drafting units. Beijing Crane Transportation Machinery Design and Research Institute, National Lifting and Transportation Machinery Quality Supervision and Inspection Center. Participated in the drafting of this section. Anhui Heli Co., Ltd., Hangcha Group Co., Ltd., Guangxi Liugong Machinery Co., Ltd. the company. The main drafters of this section. Wang Moyang, Zeng Wen, Zhao Chunhui, Li Yuansong, Liu Qiaozhen. Industrial vehicle stability verification Part 11. Telescopic forklift1 ScopeThis part of GB/T 26949 specifies the test method for verifying the stability of telescopic forklift trucks equipped with forks or load handling attachments. This section does not apply to vehicles designed to carry freight containers and off-road telescopic forklifts as specified in ISO 22915-14.2 Normative referencesThe following documents are indispensable for the application of this document. For dated references, only dated versions apply to this article. Pieces. For undated references, the latest edition (including all amendments) applies to this document. ISO 3691-2 Safety requirements and verification of industrial vehicles - Part 2. Self-propelled telescopic forklifts (Industrytruck- Safetyrequirementandverification-Part 2. Self-propeledvariable-reachtrucks) ISO 5053 Mobile Industrial Vehicle Terminology (Poweredindustrialtrucks-Terminology) ISO 22915-1 - Determination of stability of industrial vehicles - Part 1. General (Industrialtrucks-Verification of stability-Part 1.General)3 Terms and definitionsThe following terms and definitions defined by ISO 3691-2 and ISO 22915-1 apply to this document. 3.1 Telescopic forklift variable-reachtruck With retractable (or non-retractable), non-rotatable as defined in ISO 5053 or on either side of the longitudinal axis of the vehicle An articulated arm that does not exceed 5°, a counterweight lift truck for load stacking. Note 1. The load handling device can be fixed directly to the hoisting mechanism or to the sub-gantry mounted at the end of the hoisting mechanism. Note 2. Telescopic forklifts can be equipped with integral or articulated frames, stabilizers, axle locking devices as defined in ISO 3691-2 or horizontally leveling of the frame Device, or 2-wheel/4-wheel steering or articulated frame steering system. 3.2 Industrial telescopic forklift industrialvariable-reachtruck Designed for telescopic forklifts that work on solid, level, level and paved surfaces.4 test conditions4.1 General See ISO 22915-1. 4.2 Location of the vehicle on the inclined platform 4.2.1 Load bridge and steering axle Figure 1 defines the load bridge/drive axle and steering axle of the vehicle. Description. AA---the longitudinal center plane of the vehicle; BB --- steering axle (rear axle); CC --- load bridge/drive axle. Note. The load bridge/drive axle of a 4-wheel steering vehicle is also a steering axle. Figure 1 Load bridge and steering bridge 4.2.2 Test 1 and Test 2 The vehicle should be placed on a tilting platform whose steering axle BB and load bridge CC should be parallel to the tilting axis XY of the tilting platform. See Table 1. 4.2.3 Test 3, Test 4 and Test 5 The vehicle should be placed on the inclined platform in a turned state such that the MN line is parallel to the tilt axis XY of the tilting platform, see Table 1. For vehicles with articulated steering axles, the wheels on the steering axle near the XY side of the tilt axis should be parallel to XY, see Table 1. The definition of point M is as follows. a) For vehicles with articulated steering axles. point M is the intersection of the longitudinal center plane AA of the vehicle and the axis of the steering axle. The projection on the stage, see Table 1; b) For vehicles with articulated frames. point M is the intersection of the longitudinal center plane JJ of the rear frame and the fully articulated rear axle axis Projection on the inclined platform, see Table 1; c) For vehicles with axle locking devices. point M refers to the contact of the rear wheel closest to the tilting axis XY on the inclined platform The center point of the face is shown in Table 1. As shown in Table 1, point N is defined as the contact of the load wheel (or stabilizer, if fitted) closest to the tilt axis XY on the inclined platform. The center point. 4.3 Test load When conducting tests 1 and 3, the boom with the test load should be in a lifting and extending group that is most detrimental to vehicle stability. In the combined state, the fork level is also at the same time. When conducting test 5, the boom should be at the maximum lifting angle and in the maximum and minimum overhang conditions, respectively, and the fork should be horizontal. See Table 1. 4.4 lifting height Carry out the simulation running test, that is, when the test 2 and the test 4, the fork is fully inclined backward, and the measurement is started from the root of the fork, and the upper surface of the fork should be lie in. --- For vehicles with a rated lifting capacity of not more than 10t, it should be higher than the inclined platform 300mm; --- For vehicles with a rated lifting capacity greater than 10t, it should be 500mm higher than the inclined platform. See Table 1. 4.5 Lateral test procedure For vehicles with optional operating stabilizers and/or axle locks, test 1 and test 3 shall be in stabilizer/axle lock respectively The device is in working and non-working state. See Table 1.5 stability verificationThe stability of the vehicle should be verified according to Table 1.6 markUnder normal operating conditions, when the stabilizer and/or axle locking device of the vehicle is inoperative and inactive (as determined by the stability test) The weight shall be marked on the label that the operator can see in the normal operating position as specified in ISO 3691-2. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 26949.11-2016 be delivered?Answer: The full copy PDF of English version of GB/T 26949.11-2016 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 26949.11-2016_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 26949.11-2016_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 26949.11-2016 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 26949.11-2016?A step-by-step guide to download PDF of GB/T 26949.11-2016_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 26949.11-2016". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
