GB/T 11199-2024 PDF EnglishUS$200.00 · In stock · Download in 9 seconds
GB/T 11199-2024: High-purity sodium hydroxide Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid GB/T 11199: Historical versions
Similar standardsGB/T 11199-2024: High-purity sodium hydroxide---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT11199-2024GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 71.060.40 CCS G 11 Replacing GB/T 11199-2006 High-purity Sodium Hydroxide 高纯氢氧化钠 Issued on: MARCH 15, 2024 Implemented on: OCTOBER 1, 2024 Issued by. State Administration for Market Regulation; Standardization Administration of the People’s Republic of China. Table of ContentsForeword... 3 1 Scope... 5 2 Normative References... 5 3 Terms and Definitions... 6 4 Symbols... 6 5 Technical Requirements... 7 6 Sampling... 7 7 Test Method... 8 8 Inspection Rules... 13 9 Marking, Labeling and Accompanying Documents... 13 10 Packaging, Transportation and Storage... 14 Appendix A (informative) Typical Ion Chromatogram of Chlorate... 15 High-purity Sodium Hydroxide WARNING. if appropriate precautions are not taken, the products covered by this document may be dangerous during production, transportation, loading and unloading, storage, transportation and use, etc. This document does not intend to advise on all safety issues associated with this product. It is the user’s responsibility to establish appropriate safety and preventive measures and determine the applicability of relevant regulatory limitations before using this document.1 ScopeThis document specifies the technical requirements for the appearance, physical and chemical properties of high-purity sodium hydroxide, and describes the corresponding sampling, test methods, inspection rules, marking, labeling, accompanying documents, packaging, transportation and storage. This document applies to the production, use and quality control of high-purity sodium hydroxide products produced by electrolysis of sodium chloride aqueous solution.2 Normative ReferencesThe contents of the following documents constitute indispensable clauses of this document through the normative references in the text. In terms of references with a specified date, only versions with a specified date are applicable to this document. In terms of references without a specified date, the latest version (including all the modifications) is applicable to this document. GB 190 Packing Symbol of Dangerous Goods GB/T 191 Packaging - Pictorial Markings for Handling of Goods GB/T 209-2018 Sodium Hydroxide for Industrial Use GB/T 4348.1 Sodium Hydroxide for Industrial Use - Determination of Sodium Hydroxide and Sodium Carbonate Content GB/T 4348.3 Sodium Hydroxide for Industrial Use - Determination of Iron Content - 1,10- phenathroline Photometric Method GB/T 6678 General Principles for Sampling Chemical Products GB/T 6679 General Rules for Sampling Solid Chemical Products GB/T 6680 General Rules for Sampling Liquid Chemical Products GB/T 6682 Water for Analytical Laboratory Use - Specification and Test Methods GB/T 7698 Sodium Hydroxide for Industrial Use - Determination of Carbonates Content - Titrimetric Method GB/T 8170 Rules of Rounding off for Numerical Values & Expression and Judgement of Limiting Values GB/T 11200.1 Sodium Hydroxide for Industrial Use - Determination of Sodium Chlorate Content - o-Tolidine Spectrometric Method GB/T 11200.2 Test Methods of High-purity Sodium Hydroxide - Part 2.Determination of Aluminum Oxide Content - Spectrometric Method GB/T 11200.3 Test Methods of High-purity Sodium Hydroxide - Part 3.Determination of Calcium Contents - Flame Atomic Absorption Method GB/T 11213.1 Sodium Hydroxide for Chemical Fiber Use - Determination of Sodium Hydroxide Content GB/T 11213.2 Sodium Hydroxide for Chemical Fiber Use - Determination of Sodium Chloride Content - Spectrometric Method GB/T 11213.4 Sodium Hydroxide for Chemical Fiber Use - Determination of Silicon Content - Reduced Molybdosilicate Spectrophotometric Method GB/T 11213.5 Sodium Hydroxide for Chemical Fiber Use - Determination of Sulphate Content GB 15258 General Rules for Preparation of Precautionary Label for Chemicals GB/T 31197-2014 Inorganic Chemicals for Industrial Use - Determination of Impurity Anions - Ion Chromatography Method HG/T 3942 Sodium Hydroxide for Industrial Use - Determination of Metal and Nonmetal Ions Content - ICP Method3 Terms and DefinitionsThis document does not have terms or definitions that need to be defined.4 SymbolsThe following symbols apply to this document. HL. high-purity liquid sodium hydroxide. HS. high-purity solid sodium hydroxide. bag shall prevail. The volume of each sample shall not be less than 500 g. 6.3 For high-purity liquid sodium hydroxide products, in accordance with the provisions of GB/T 6680, from the top, middle and bottom of the tank truck or storage tank, take equal amounts of representative samples, mix the samples, put them in two clean, dry, stoppered polyethylene bottles and seal them. Manufacturers may collect samples at the sampling port of the finished product tank or use an automatic sampling device or manually collect representative samples on the pipeline before entering the finished product tank. When a dispute arises between the supply-side and the demand-side regarding product quality, representative samples taken from the top, middle and bottom of the tank truck or storage tank after stirring and mixing shall prevail. The volume of each sample shall not be less than 500 mL. 6.4 The sample bottle shall be labeled and marked with. manufacturer name, product name, model, batch No. or production date, sampling date and sampler, etc.7 Test Method7.1 Appearance Under natural light, conduct visual observation. 7.2 Determination of Mass Fraction of Sodium Hydroxide In accordance with the provisions of GB/T 4348.1 or GB/T 11213.1, conduct the determination. Between them, GB/T 11213.1 is the arbitration law. 7.3 Determination of Mass Fraction of Sodium Carbonate In accordance with the provisions of GB/T 4348.1 or GB/T 7698, conduct the determination. Between them, GB/T 7698 is the arbitration law. 7.4 Determination of Mass Fraction of Sodium Chloride In accordance with the provisions of GB/T 11213.2 or Appendix A of GB/T 209-2018, conduct the determination. Between them, Appendix A of GB/T 209-2018 is the arbitration law. 7.5 Determination of Mass Fraction of Ferric Oxide In accordance with the provisions of GB/T 4348.3 or HG/T 3942, conduct the determination. Between them, HG/T 3942 is the arbitration law. 7.6 Determination of Mass Fraction of Silicon Dioxide In accordance with the provisions of GB/T 11213.4 or HG/T 3942, conduct the determination. Between them, HG/T 3942 is the arbitration law. 7.7 Determination of Mass Fraction of Sodium Sulfate In accordance with the provisions of GB/T 11213.5, conduct the determination. 7.8 Determination of Mass Fraction of Sodium Chlorate 7.8.1 Spectrophotometric method (arbitration method) Comply with the provisions of GB/T 11200.1. 7.8.2 Ion chromatography 7.8.2.1 Principle After the sample is prepared into a specimen solution, take an appropriate amount of the specimen solution and inject it into the ion chromatographic column through the injection system. Use an appropriate eluent to elute it. The active exchange groups on the ion exchange resin exchange ions with the ions in the specimen solution and the ions in the eluent. As the eluent flows, the anions in the specimen solution are continuously exchanged - eluted - re- exchanged - re-eluted. The anions under test are separated based on their different retention characteristics on the chromatographic column and finally brought to the detector by the eluent. The detection signal forms a Gaussian distribution chromatographic peak on the chromatogram. Under certain chromatographic conditions, the retention time of each component is fixed, which is used as the qualitative basis for the component ions; within a certain concentration range, the peak area or peak height of the component is proportional to the concentration of the component, and the peak area or peak height is used as the quantitative basis for the component ions. 7.8.2.2 Reagents or materials 7.8.2.2.1 Unless otherwise specified, only guaranteed reagents and Grade-1 water specified in GB/T 6682 or water of equivalent purity shall be used in the analysis. 7.8.2.2.2 Sodium carbonate solution. 3.6 mmol/L. Weigh-take 19.08 g of anhydrous sodium carbonate (accurate to 0.01 g) burned at 270 C ~ 300 C to a constant weight, dissolve it in water, cool to room temperature, transfer to a 500 mL volumetric flask, use water to dilute to the scale, and shake it well. Use a pipette to measure- take 5 mL into a 500 mL volumetric flask, use water to dilute to the scale, and shake it well. The solution shall be stored in polyethylene or polytetrafluoroethylene reagent bottles. 7.8.2.2.3 Sodium hydroxide solution. 13 mmol/L. Weigh-take 0.52 g of sodium hydroxide (accurate to 0.01 g), dissolve it in water, cool to room temperature, transfer it into a 1,000 mL volumetric flask, use water to dilute to the scale, and shake it well. The solution shall be stored in polyethylene or polytetrafluoroethylene reagent bottles. 7.8.2.2.4 Potassium hydroxide solution. 13 mmol/L. 7.10 Determination of Mass Fraction of Calcium Oxide In accordance with the provisions of GB/T 11200.3 or HG/T 3942, conduct the determination. Between them, HG/T 3942 is the arbitration law.8 Inspection Rules8.1 Inspection Classification and Inspection Items 8.1.1 Inspection classification The inspection is classified into type inspection and exit-factory inspection. 8.1.2 Type inspection Type inspection items include all inspection items specified in this document. Under normal production conditions, type inspection shall be carried out at least once a month. If any of the following situations occur, type inspection shall be carried out. ---Resumption of production after suspension; ---Relatively significant changes in production process (such as. materials and process conditions, etc.); ---After major fluctuations and adjustments in production equipment. 8.1.3 Exit-factory inspection The exit-factory inspection items are appearance, mass fraction of sodium hydroxide and mass fraction of sodium chloride. 8.2 Determination Rules Product quality indicators are determined in accordance with the “rounded value comparison method” in GB/T 8170. 8.3 Re-inspection Rules If one of the indicators in the inspection results does not meet the requirements of this document, double the quantity of representative samples shall be taken from the packaging unit for re- inspection. If one or more indicators in the re-inspection results do not meet the requirements of this document, then, the batch of products will be determined as disqualified products.9 Marking, Labeling and Accompanying Documents9.1 Marking The outer packaging of high-purity sodium hydroxide products exiting the factory shall have obvious and firm markings, including production enterprise’s name, address, product name, serial No. of implemented Standard, model, batch No. or production date, net weight and the “corrosive substance” mark specified in GB 190.High-purity solid sodium hydroxide products shall also have the “rain-proof” mark specified in GB/T 191. 9.2 Labeling It shall comply with the provisions of GB 15258. 9.3 Accompanying Documents Each batch of high-purity sodium hydroxide products exiting the factory shall be inspected by the quality supervision and inspection department of the production enterprise in accordance with the requirements of this document and accompanied by a quality certification document, including production enterprise name, product name, model, quality indicator, batch No. or production date, and serial No. of this document.10 Packaging, Transportation and Storage10.1 Packaging 10.1.1 For high-purity solid sodium hydroxide products in the form of flakes, granules or blocks, polyethylene or polypropylene film bags should be used as inner bags, and polyethylene or polypropylene woven bags (or laminated bags) or kraft paper bags should be used as outer bags. The net weight of each bag is 25.0 kg. Based on the agreement between the supply-side and the demand-side, other appropriate packaging modes and packaging quantities may also be adopted. The packaging bags and seals shall ensure that the products will not be contaminated or leaked during normal storage and transportation. 10.1.2 High-purity liquid sodium hydroxide products shall be shipped and transported in special tank trucks or storage tanks, and the packaging containers shall not contaminate the products. 10.2 Transportation and Storage 10.2.1 During transportation, avoid collision. For bag-packed high-purity sodium hydroxide products, avoid packaging damage, and being affected by moisture and contamination. The products shall not be transported together with acidic items. 10.2.2 High-purity solid (including flaky, granular and blocky, etc.) sodium hydroxide products shall be stored in dry and clean warehouses; high-purity liquid sodium hydroxide products shall be stored in storage tanks. Avoid collision and contact with acidic objects. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 11199-2024 be delivered?Answer: The full copy PDF of English version of GB/T 11199-2024 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 11199-2024_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 11199-2024_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 11199-2024 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.Question 5: Should I purchase the latest version GB/T 11199-2024?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 11199-2024 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.How to buy and download a true PDF of English version of GB/T 11199-2024?A step-by-step guide to download PDF of GB/T 11199-2024_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 11199-2024". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
