HJ 2535-2013_English: PDF (HJ2535-2013)
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | Status | PDF |
| HJ 2535-2013 | English | 239 |
Add to Cart
|
3 days [Need to translate]
|
Technical requirement for environmental labeling products Room air conditioners
| Valid |
HJ 2535-2013
|
Standards related to: HJ 2535-2013
| Standard ID | HJ 2535-2013 (HJ2535-2013) | | Description (Translated English) | Technical requirement for environmental labeling products Room air conditioners | | Sector / Industry | Environmental Protection Industry Standard | | Word Count Estimation | 9,996 | | Older Standard (superseded by this standard) | HJ/T 304-2006 | | Regulation (derived from) | Ministry of Environmental Protection Bulletin No. 3, 2014 | HJ 2535-2013
(Technical requirements for environmental labeling products - Room Air Conditioners)
People's Republic of China National Environmental Protection Standards
Replacing HJ/T 304-2006
Environmental Labeling Products
Room air conditioner
Technical requirement for environmental labeling products
Room air conditioners
2014-1-13 release
2014-3-1 implementation
Issued by the Ministry of Environmental Protection
Table of Contents
Introduction .. 3
1. Scope 4
2. Normative references 4
3. Terms and definitions ..4
4. Basic requirements 5
5. The technical content of 5
6. Test Method 7
Appendix A (normative) plastic parts disable phthalates .8
Appendix B (normative) restricting the use of polycyclic aromatic hydrocarbons (PAHs) 9
Foreword
To implement the "People's Republic of China Environmental Protection Law", reducing the room air conditioner in the production and use on the environment and human
Health effects, environmental protection, development of this standard.
The standard of environmental design of the room air conditioner, production processes, energy consumption, noise, toxic and harmful substances, recycling
And recycling and other proposed requirements.
This standard of "environmental labeling products technical requirements for room air conditioner" (HJ/T 304-2006) the technical contents of repair
Order, the main changes are as follows.
- Expanding the product range, the speed-controlled room air conditioners and refrigeration products and the amount is less commercial 14000W
Air conditioning included in the standard range;
- Added refrigerant requirements;
- Increasing the requirements for hazardous substances;
- Improving the energy efficiency requirements;
- Increased noise requirements;
- Increase the production process control requirements.
This standard applies to Chinese environmental product certification mark.
This standard is developed by the Ministry of Environmental Protection Science, Technology organization.
This standard is mainly drafted by. Ministry of Environmental Protection and Development Center, Daikin (China) Investment Co., Ltd.
This standard MEP January 13, 2014 for approval.
This standard since March 1, 2014 implementation.
The standard explanation by the Ministry of Environmental Protection.
This standard replaces the standards previously issued as follows.
--HJ BZ 18-1997, HJ BZ 18-2000, HJ/T 304-2006.
Environmental labeling products technical requirements for room air conditioners
1. Scope
This standard specifies the terms and definitions room air conditioner for environmental labeling products, basic requirements, technical contents, and testing methods.
This standard applies to the use of air-cooled and water-cooled condenser, Hermetic motor - compressors, cooling capacity and less household 14000W
And similar use of room air conditioners.
This standard does not apply to the following products.
- Mobile air conditioners;
- Integral room air conditioner;
- Does not form a separate component complete refrigeration systems;
- Use the air conditioner absorption refrigeration cycle.
2. Normative references
This standard refers to the contents of the following documents contain provisions which, undated references, the effective version applies to this standard.
GB/T 16288 plastic signs
GB/T 18455 Packaging Recycling Marks
GB/T 20861-2007 waste products recycling terminology
GB/T 26572 Limited restricted substances in electrical and electronic equipment requirements
HJ/T 239 environmental labeling products technical requirements for batteries
3. Terms and Definitions
The following terms and definitions apply to this standard.
3.1 room air conditioners room air conditioner
A method of providing treated air device directly to an enclosed space, room or area. Including refrigeration and dehumidification cooling
Systems and air circulation and purification device may further include a heating and ventilation system (which can be assembled in a box or housing designed to
Components of the system for use with), such as free air-type air conditioners, water source heat pump, air conditioner unit, air duct type
Air conditioning units, multi-type air conditioning units, roof air conditioner and the like.
3.2 ODP ozne depleting potential (ODP)
It refers to a substance in its atmospheric lifetime, global ozone losses relative to the same mass of CFC-11 emissions caused by
The ratio of ozone loss.
3.3 Renewable utilization recyclability rate
Product quality can be regenerated using part (excluding energy recovery) as a percentage of product quality. (GB/T 20861-2007)
4. Basic Requirements
4.1 Quality of products shall meet the quality standards appropriate.
4.2 product safety, electromagnetic compatibility shall comply with the appropriate standards.
4.3 Pollutant emissions should conform with pollutant emission standards national or local regulations.
4.4 products manufacturing enterprises in the production process should strengthen cleaner production, cleaner production and meet the appropriate standards.
5. Technical Content
5.1 Environmental product design requirements
5.1.1 easy to recycle design
5.1.1.1 product recycling rate of not less than 83%.
5.1.1.2 mass exceeding 25g, or planar surface area over 200mm2 plastic parts should use a single type of polymer or copolymerizing
Thereof.
5.1.1.3 mass of more than 25g, and the flat surface area over 200mm2 plastic parts shall be in accordance with GB/T 16288 standard requirements
Shown.
5.1.2 Parts of hazardous substances requirements
5.1.2.1 product refrigerant used ozone-depleting potential (ODP) should be 0.
5.1.2.2 product base housing and the circuit board can not use short-chain chlorinated paraffins (SCCPs), in an amount not exceeding the total plastic parts
0.1% by volume.
5.1.2.3 Product quality is greater than 25g of the housing plastic parts shall not use chlorine, bromine-containing polymer, not add chlorine containing organic
Compound, an organic bromine compound flame retardant.
5.1.2.4 In addition to wire and cable products, the quality is greater than 25g plastic parts shall not be used phthalates listed in Appendix A
As a plasticizer.
5.1.2.5 Product remote shell, all kinds of buttons, filters and an external power supply line of benzo (a) pyrene in the total amount should not exceed 20 mg/kg,
18 polycyclic aromatic hydrocarbons (PAHs) listed in Appendix B of the total amount should not exceed 200 mg/kg.
5.1.2.6 product comes with batteries should be consistent with HJ/T 239 requirements.
5.2 Production stage requires
5.2.1 should have the refrigerant recovery.
5.2.2 not use HCFCs (HCFCs), 1,1,1- trichloroethane (C2H3Cl3), trichlorethylene (C2HCl3), dichloroethane
Alkyl (CH3CHCl2), methylene chloride (CH2Cl2), chloroform (CHCl3), carbon tetrachloride (CCl4), bromopropane (C3H7Br)
And other substances as a cleaning solvent.
5.2.3 parts assembly, the connection process should be lead-free soldering processes.
5.2.4 sheet metal pre-treatment process may not use phosphorus degreasing agent and a coating agent.
5.3 Product Requirements
5.3.1 Products of restricted substances limit requirement should be consistent with GB/T 26572 requirements.
5.3.2 product meets the requirements of the respective national energy efficiency standards in energy conservation evaluation values.
5.3.3 product is not greater than the rated noise requirements of Table 3.
Table 3 products rated noise (SPL)
Test items rated cooling capacity/kW rated noise/dB (A)
Rated noise
≤2.5
The indoor unit 39
With static pressure indoor unit 40
The outdoor unit 49
> 2.5 to 4.5
The indoor unit 41
With static pressure indoor unit 42
The outdoor unit 52
> 4.5 ~ 7.1
The indoor unit 43
44 of the indoor unit with hydrostatic
The outdoor unit 56
> 7.1
The indoor unit 47
Indoor unit with static pressure of 48
The outdoor unit 59
5.4 product packaging requirements
5.4.1 not use HCFCs (HCFCs) as a blowing agent.
5.4.2 the total amount of packaging and packaging materials in heavy metals lead, cadmium, mercury and hexavalent chromium should not exceed 100mg/kg.
5.4.3 shall be in accordance with GB/T 18455 were marked.
5.5 Product recycling requirements
Products recycling company should provide prompt statements and other information.
5.6 Description of requirements
Product description required to deliver products together with users, should include the following.
a) product maintenance instructions.
b) the product in standby mode and statements only when the product is not connected to the input power in order to achieve zero energy consumption at tips.
c) correctly set temperature during the heating lower than expected 2 ℃, 2 ℃ high cooling to save energy.
d) use of air conditioning, avoid direct sunlight room; do not frequently switch doors, windows.
e) clean the filter regularly.
f) to provide products in the product design and manufacturing companies all serviceable life of replacement parts to ensure that the product design life
Life during normal use.
6. Test Method
6.1 Technical content 5.3.2.1 testing according to their energy efficiency standards identified in the method.
6.2 5.3.3 The technical contents of their products tested according to the corresponding standard method.
6.3 Technical requirements for the contents of other documents reviewed by the combination of field-proven way to verify.
Appendix A
(Normative)
Plastic parts in the banned phthalates
Chinese name English name abbreviation
Diisononyl phthalate Di-iso-nonylphthalate DINP
Phthalate, di-n-octyl phthalate Di-n-octylphthalate DNOP
Bis (2-ethylhexyl) phthalate Di- (2-ethylhexy) -phthalate DEHP
Diisodecyl phthalate Di-isodecylphthalate DIDP
Phthalate, butyl benzyl phthalate Butylbenzylphthalate BBP
Dibutyl phthalate, Dibutylphthalate DBP
Appendix B
(Normative)
Restricting the use of polycyclic aromatic hydrocarbons (PAHs)
Chinese name English name abbreviation
Naphthalene Naphthalene Nap
Acenaphthylene Acenaphthylene AcPy
Acenaphthene Acenaphthene Acp
Fluorene Fluorene Flu
Philippines Phenanthrene PA
Anthracene Anthracene Ant
Fluoranthene Fluoranthene FL
Pyrene Pyrene Pyr
Chrysene Chrysene CHR
Benzo (a) anthracene Benzo [a] anthracen BaA
Benzo (b) fluoranthene Benzo [b] fluoranthene BbF
Benzo (k) fluoranthene Benzo [k] fluoranthene BkF
Benzo (a) pyrene Benzo [a] pyrene BaP
Dibenzo (a, h) anthracene Dibenzo [a, h] anthrancene DBA
Indeno (1,2,3-cd) pyrene Indeno [1,2,3-cd] pyrene IND
Benzo (g, h, i) perylene (perylene) Benzo [g, h, i] perylene BghiP
Benzo [j] fluoranthene Benzo [j] fluoranthene
Benzo [e] perylene Benzo [e] pyrene
...
|