|
US$434.00 ยท In stock
Delivery: <= 4 days. True-PDF full-copy in English will be manually translated and delivered via email.
GB/T 41850.9-2024: Mechanical vibration - Measurement and evaluation of machine vibration - Part 9: Gear units
Status: Valid
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Standard Title (Description) | Status | PDF |
| GB/T 41850.9-2024 | English | 434 |
Add to Cart
|
4 days [Need to translate]
|
Mechanical vibration - Measurement and evaluation of machine vibration - Part 9: Gear units
| Valid |
GB/T 41850.9-2024
|
PDF similar to GB/T 41850.9-2024
Basic data | Standard ID | GB/T 41850.9-2024 (GB/T41850.9-2024) | | Description (Translated English) | Mechanical vibration - Measurement and evaluation of machine vibration - Part 9: Gear units | | Sector / Industry | National Standard (Recommended) | | Classification of Chinese Standard | J04 | | Classification of International Standard | 17.160 | | Word Count Estimation | 22,243 | | Date of Issue | 2024-12-31 | | Date of Implementation | 2025-07-01 | | Issuing agency(ies) | State Administration for Market Regulation, China National Standardization Administration | GB/T 41850.9-2024: Mechanical vibration - Measurement and evaluation of machine vibration - Part 9: Gear units
---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.
ICS 17.160
CCSJ04
National Standard of the People's Republic of China
Mechanical vibration Measurement and evaluation of machine vibration
Part 9.Gear units
Part 9.Gear units
(ISO 20816-9.2020, IDT)
Released on 2024-12-31
2025-07-01 Implementation
State Administration for Market Regulation
The National Standardization Administration issued
Table of Contents
Preface III
Introduction IV
1 Scope 1
2 Normative references 1
3 Terms and Definitions 1
4 General 2
4.1 System Considerations 2
4.2 System Impact 2
4.3 Measurement of housing or shaft 2
5 Instruments 2
5.1 Type 2
5.2 Measurement frequency range 3
5.3 Permissible error 3
5.4 Calibration 3
6 Vibration Measurement 3
6.1 Axis measurement 3
6.2 Shell Measurement 4
6.3 Units of measurement 4
7 Test status 4
7.1 General 4
7.2 Test system layout 4
7.3 Test conditions 5
8 Evaluation criteria 5
8.1 General 5
8.2 Evaluation Area 5
8.3 Acceptance criteria 5
8.4 Boundary of vibration assessment area 6
8.5 Classification 7
9 Test Report 8
9.1 General 8
9.2 Manufacturer 8
9.3 Operational data 8
9.4 Layout description 8
9.5 Measuring equipment 8
9.6 Test measurements and results 8
9.7 Acceptance test approval 9
Appendix A (Informative) Grade curves for vibration displacement and vibration velocity measurements 10
A.1 Overview 10
A.2 Amplitude curve 10
A.3 Subjective vibration level evaluation 12
Appendix B (Informative) Impact of the system 13
B.1 Overview 13
B.2 Typical factors affecting the system 13
B.3 Responsibility14
Appendix C (Informative) Notes on vibration instruments and characteristics 15
C.1 Overview 15
C.2 Instruments for measuring housing vibration and shaft vibration 15
C.3 Measurement of housing vibration 15
C.4 Axis displacement measurement 15
Reference 17
Foreword
This document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for standardization work Part 1.Structure and drafting rules for standardization documents"
Drafting.
This document is part 9 of GB/T 41850 "Mechanical vibration - Measurement and evaluation of machine vibration". GB/T 41850 has been published
The following parts.
--- Part 1.General;
--- Part 8.Reciprocating compressor systems;
--- Part 9.Gear units.
This document is equivalent to ISO 20816-9.2020 "Mechanical vibration - Measurement and evaluation of machine vibration - Part 9.Gear units".
Please note that some of the contents of this document may involve patents. The issuing organization of this document does not assume the responsibility for identifying patents.
This document was proposed and coordinated by the National Technical Committee for Standardization of Mechanical Vibration, Shock and Condition Monitoring (SAC/TC53).
This document was drafted by. Zhengzhou Machinery Research Institute Co., Ltd., Nanjing High-precision Gear Group Co., Ltd., Xiamen Qinghua Intelligent Transmission Co., Ltd.
Company, Zhejiang Dazhong Gear Co., Ltd., Changxing Shengyang Technology Co., Ltd., Zhejiang Fengan Gear Co., Ltd., Zhejiang Xiangrui Electromechanical Equipment
Co., Ltd., China Datang Group Science and Technology Research Institute Co., Ltd. Central South Electric Power Test Institute, Nanjing Chuangli Transmission Machinery Co., Ltd.
Hangzhou Interpulse Transmission Co., Ltd., Magfa (Shanghai) Technology Co., Ltd., China Digital Intelligence (Hangzhou) Technology Co., Ltd., CRRC
Zhuzhou Electric Locomotive Co., Ltd., Chongqing Zhizhan Gear Transmission Co., Ltd., Zhejiang Lawrence Machine Tool Co., Ltd., Jiangsu Xinyinye Transmission Electromechanical
Co., Ltd., Henan Ruige Transmission Machinery Co., Ltd., Hubei Huazhong Electric Power Technology Development Co., Ltd., Henan Jiuyu Enpai Electric Power Technology
TECHNOLOGY LIMITED.
The main drafters of this section are. Ma Weiping, Wang Peng, Yi Zhonghui, Pan Dan, Yang Jun, Hong Xinyang, Zhang Xinwei, Zeng Yanping, Chen Liang, Xu Wenbo, Zhang Xiangru,
Dou Lisha, Xia Yalei, Li Yong, Fei Xiuguo, Jiang Jian, Zhao Yuanjin, Xu Sheng, Shen Longjiang, He Rong, Ye Silin, Xu Ning, Yang Xingkai, Wu Jinguo, Guo Yujie.
Introduction
GB/T 41850 "Mechanical vibration - Measurement and evaluation of machine vibration" provides the measurement and evaluation of vibration on non-rotating parts and rotating shafts.
The requirements and guidelines for machine vibration are intended to consist of the following parts.
--- Part 1.General. The purpose is to give a general description of the measurement and evaluation of various types of machine vibration on non-rotating parts and rotating shafts.
General requirements.
--- Part 2.For engines with a capacity of 40MW or more and using sliding bearings, the rated speed is 1500r/min, 1800r/min, 3000r/min
and 3600r/min land-mounted gas turbines, steam turbines and generators. The purpose is to give the gas turbines installed on large land
Detailed evaluation of bearing housing vibrations and shaft vibrations in turbines, steam turbines and generators.
--- Part 4.Gas turbines with sliding bearings above 3 MW. The purpose is to give gas turbines not covered in Part 2.
Detailed evaluation of machine bearing housing vibration and shaft vibration.
--- Part 5.Hydroelectric and pumped storage power station units. The purpose is to give the bearings of hydroelectric and pumped storage power station units
Guide for the measurement and evaluation of seat and shaft vibrations.
--- Part 8.Reciprocating compressor systems. The purpose is to establish specific requirements for the measurement and classification of mechanical vibrations in reciprocating compressor systems.
specific procedures and guidelines.
--- Part 9.Gearing. The purpose is to give specific provisions for measuring and evaluating vibration of gearing.
Mechanical vibration Measurement and evaluation of machine vibration
Part 9.Gear units
1 Scope
This document specifies the specific requirements for the determination and classification of mechanical vibrations in single-cased, enclosed step-up or step-down gear units.
The method of measuring housing vibration and shaft vibration is given, as well as the instrument type, measurement method and test procedure for determining the vibration value.
The vibration levels used for acceptance are given.
This document does not cover the measurement of torsional vibrations.
This document applies to the acceptance of gear units operating within their design speed, load, temperature and lubrication ranges at the manufacturer's facilities.
This document can also be used to guide site acceptance testing and routine operational measurements, as agreed between the manufacturer and the customer and/or operator.
This document is applicable to rated power of 10kW~100MW and rated speed of 30r/min~12000r/min (0.5Hz~200Hz)
gear device.
This document does not apply to special or auxiliary drive trains, such as integrated gear driven compressors, pumps, turbines, etc. or to those used in combined cycle turbines.
Gear clutch between the turbine generator and the power output gear.
The evaluation criteria provided in this document can be applied to the vibration of the main input and output shaft bearings and the vibration of the internal shaft bearings of the gearbox.
This document is not intended to be used to assess the condition of gears.
This document establishes the provisions for the evaluation of broadband vibration severity of the following sites under normal stable operating conditions.
a) Structural vibration measured radially (i.e. lateral) at all main bearing housings or foundations;
b) Structural vibration measured axially in the thrust bearing housing;
c) radial (i.e. lateral) vibration of the rotating shaft at or near the main bearing;
d) Structural vibration of the gearbox.
NOTE This document does not cover vibrations occurring under non-steady-state conditions (when transient changes occur), including increasing or decreasing speed, initial loading and changes in load.
2 Normative references
The contents of the following documents constitute the essential clauses of this document through normative references in this document.
For referenced documents without a date, only the version corresponding to that date applies to this document; for referenced documents without a date, the latest version (including all amendments) applies to
This document.
ring-Vocabulary)
Note. GB/T 2298-2010 Mechanical vibration, shock and condition monitoring vocabulary (ISO 2041.2009, IDT)
Note. GB/T 13824-2015 Requirements for vibration severity measuring instruments for mechanical vibration of rotating and reciprocating machines (ISO 2954.2012, IDT)
ISO 10817-1 Rotating shaft vibration measurement systems Part 1.Relative and absolute detection of radial vibration (Rotatingshaftvibra-
Note. GB/T 21487.1-2008 Shaft vibration measurement systems Part 1.Relative and absolute detection of radial vibration (ISO 10817-1.1998, IDT)
3 Terms and definitions
For the purposes of this document, the terms and definitions defined in ISO 2041 and the following apply.
Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 41850.9-2024_English be delivered?Answer: Upon your order, we will start to translate GB/T 41850.9-2024_English as soon as possible, and keep you informed of the progress. The lead time is typically 2 ~ 4 working days. The lengthier the document the longer the lead time. Question 2: Can I share the purchased PDF of GB/T 41850.9-2024_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 41850.9-2024_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to [email protected]. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.
|