NB/T 11638-2024 English PDFUS$299.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. NB/T 11638-2024: Method for determining the extraction volume of single-layer gas in multi-coal seam by drilling through - Seam holes: measured flow rate method Status: Valid
Basic dataStandard ID: NB/T 11638-2024 (NB/T11638-2024)Description (Translated English): Method for determining the extraction volume of single-layer gas in multi-coal seam by drilling through - Seam holes: measured flow rate method Sector / Industry: Energy Industry Standard (Recommended) Classification of Chinese Standard: D09 Classification of International Standard: 13.100 Word Count Estimation: 13,159 Date of Issue: 2024-09-24 Date of Implementation: 2025-03-24 Issuing agency(ies): National Energy Administration NB/T 11638-2024: Method for determining the extraction volume of single-layer gas in multi-coal seam by drilling through - Seam holes: measured flow rate method---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/NBT11638-2024 Method for determining the extraction volume of single-layer gas in multi-coal seam by drilling through - Seam holes. measured flow rate method Energy Industry Standards of the People's Republic of China The National Energy Administration released Gas extraction volume of a single layer in multi-coal seam by pre-extraction through through-layer drilling Determination method. measured flow method Method for determining the extraction volume of single⁃layer gas in multi⁃coal seam by drilling through-Seam holes. measured flow rate method Released on September 24, 2024 2025-03-24 Implementation CCS D 09 ICS 13.100 Preface III 1 Scope 1 2 Normative references 1 3 Terms and Definitions 1 4 Method Principle 1 5 General Requirements 1 6 Preparation before measurement 1 7 Measurement process 2 8 Calculation of measurement results 4 9 Determination of single layer extraction volume during combined pre-extraction 5 Appendix A (Informative) Record Sheet for Determining Drilling Construction Parameters 6 Appendix B (Informative) Gas Drainage Parameter Measurement Record Sheet 7 Appendix C (Informative) Extraction Volume Ratio Calculation Results Record Table 8 Table of ContentsPreface This document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for standardization work Part 1.Structure and drafting rules for standardization documents" Drafting. Please note that some of the contents of this document may involve patents. The issuing organization of this document does not assume the responsibility for identifying patents. This document was proposed by the China Coal Industry Association. This document is under the jurisdiction of the Coal Industry Coal Mine Safety Standardization Technical Committee. This document was drafted by. China Coal Technology and Engineering Group Chongqing Research Institute Co., Ltd., Heilongjiang Longmei Jixi Mining Co., Ltd., Chongqing University, Hunan Gas Control and Utilization Engineering Research Center Co., Ltd., Xi'an University of Science and Technology. The main drafters of this document are. Zhao Xusheng, Ding Hong, Wang Zhen, Wu Jiaokun, Chen Yong, Liu Xianjun, Ge Zhaolong, Ma Hongyu, Zhang Tianjun, Liu Zhiwei, Cao Jiahua, Pan Hongyu, Ji Daorong, Lian Changjun, Zhang Zhonghai, Jia Xiaoliang, Deng Zhaoyu, Huang Guangli, Zhou Mi, and Zhang Mingming. Gas extraction volume of a single layer in multi-coal seam by pre-extraction through through-layer drilling Determination method. measured flow method 1 Scope This document specifies the principle, general requirements, and Preparation before measurement, measurement process and calculation of measurement results. This document is applicable to the investigation and determination of the proportion of single-layer extraction volume when through-layer drilling is used to pre-extract gas from multiple coal seams in underground coal mines. 2 Normative references The contents of the following documents constitute the essential clauses of this document through normative references in this document. For referenced documents without a date, only the version corresponding to that date applies to this document; for referenced documents without a date, the latest version (including all amendments) applies to this document. document. GB/T 15663.8 Coal Mine Scientific and Technological Terminology Part 8.Coal Mine Safety MT/T 642 Technical Specifications for Instruments for Measuring Comprehensive Parameters of Gas Drainage in Pipelines 3 Terms and Definitions The terms and definitions defined in GB/T 15663.8 and the following apply to this document. 3.1 target coal seam When conducting through-layer drilling combined with pre-extraction of multiple coal seam gas, it is necessary to determine the extraction volume of each coal seam. 4 Principles of the Method In the investigation area where coal seams and gas occurrence conditions are relatively stable, drilling holes are constructed in the target coal seams and multiple coal seams respectively. Under the condition that the sealing process and extraction negative pressure and other parameters are basically the same, the extraction volume of the target coal seam alone and the extraction volume of multiple coal seams are measured respectively. Calculate the ratio of individual extraction volume to combined extraction volume. Determine the combined pre-extraction volume of multiple coal seams in areas with similar coal seam and gas occurrence conditions. The basis for calculating the extraction volume of a single target coal seam. 5 General requirements 5.1 The measurement site should be selected in an area where gas extraction has not been carried out, and the coal seams and gas occurrence conditions in the selected area should be representative. 5.2 For adjacent coal seams with an average normal distance of less than 5 m from the target coal seam, the mine may inspect them together with the target coal seam based on actual needs. 5.3 The gas extraction flow rate should be measured manually on site. 6 Preparation before measurement 6.1 Instruments used to measure gas extraction flow should be within the validity period of calibration and meet the following requirements. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of NB/T 11638-2024_English be delivered?Answer: Upon your order, we will start to translate NB/T 11638-2024_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of NB/T 11638-2024_English with my colleagues?Answer: Yes. The purchased PDF of NB/T 11638-2024_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
