GB/T 26112-2010 English PDFUS$299.00 ยท In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 26112-2010: Micro-electromechanical system technology -- General rules for the assessment of micro-mechanical parameters Status: Valid
Basic dataStandard ID: GB/T 26112-2010 (GB/T26112-2010)Description (Translated English): Micro-electromechanical system technology -- General rules for the assessment of micro-mechanical parameters Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: L55 Classification of International Standard: 31.2 Word Count Estimation: 13,154 Date of Issue: 1/10/2011 Date of Implementation: 10/1/2011 Quoted Standard: GB/T 26111, Regulation (derived from): Announcement of Newly Approved National Standards 2011 No. (No. 166 overall) 1 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China Summary: This Standard specifies the basic principles of assessment micromechanical amount of assessment factors, assessment procedures, evaluation methods and assessment rules. This Standard is applicable to enterprises, research institutions, seizure detection mechanism in MEMS technology and product research, design, production, testing and use. GB/T 26112-2010: Micro-electromechanical system technology -- General rules for the assessment of micro-mechanical parameters---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Micro-electromechanical system technology. General rules for the assessment of micro-mechanical parameters ICS 31.200 L55 National Standards of People's Republic of China Micro-electromechanical systems (MEMS) technology General assessment of the amount of micro-mechanical Issued on. 2011-01-10 2011-10-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released ForewordThis standard was drafted in accordance with GB/T 1.1-2009 given rules. This standard by the National MEMS Technology Standardization Technical Committee (SAC/TC336) and focal points. This standard was drafted. Tianjin University, the machine Productivity Promotion Center, Xi'an Jiaotong University, Dalian University of Technology, Taiyuan University of Technology, China Former Institute of Technology. The main drafters of this standard. Hu Xiaodong, Ding Hongyu, Liu Wei, Zhang Ping, Jing Wei Xuan, Jiang Zhuang De, Liu Chong, ROCKETS, Zhao Zexiang. Micro-electromechanical systems (MEMS) technology General assessment of the amount of micro-mechanical1 ScopeThis standard specifies the basic principles of micro-mechanical assessment of the amount of assessment factors, assessment procedures, evaluation methods and assessment rules. This standard applies to enterprises, research institutions, testing organizations engaged in MEMS technology and product research, design, production, testing and use.2 Normative referencesThe following documents for the application of this document is essential. For dated references, only the edition are not applicable to the present file. For undated references, the latest edition (including any amendments) applies to this document. GB/T 26111 micro-electromechanical systems (MEMS) technology terms3 Terms and DefinitionsGB/T 26111 and defined by the following terms and definitions apply to this document. 3.1 Micromechanical amount of micro-mechanicalparameters It refers to all the micro-mechanical nature and status of the relevant physical quantities, including geometry, flow, temperature, acoustics, mechanical and physical exercise; Since the geometry, flow, temperature, acoustic and other physical quantities for a special classification, it refers to the amount of micro-mechanical displacement, velocity, acceleration, vibration Motion parameters and other characteristics, and characteristics associated with the movement of the mechanical parameters. 3.2 Microdisplacement Microscaledisplacement Description of particle in the micron-scale changes in the physical location, its size is equal to a straight line from the starting point to the end point, the direction from the starting point end. Note 1. micro structure under the conditions subject to certain incentives will produce changes in the position, change in position, there are two typical forms of translation and rotation, corresponding bit line Shift and angular displacement. Note 2. If the micro-structure of the substrate as a reference plane, and the plane parallel to the reference plane displacement of plane displacement, otherwise known plane displacement. 3.3 Vibration vibration Reciprocating movement of the object. In the direction of the reciprocating motion can be divided into line vibration and angular vibration. Evaluation of the vibration characteristics of microstructures main package Comprising. vibration amplitude, resonance frequency, vibration mode, the quality factor. 3.4 Residual Stress residualstress After the micro-machining process is completed, there is no external force, the internal micromechanical structure and balance remaining stress, called residual Stress is the combined effects of stress and external stress and thermal stress. 3.5 Stress gradient stressgradient Micromechanical structure due to residual non-uniform distribution of residual stress in the thickness direction, suspended micromechanical structures in the lower portion of the sacrificial layer after release ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 26112-2010_English be delivered?Answer: Upon your order, we will start to translate GB/T 26112-2010_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 26112-2010_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 26112-2010_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay. |
