GB/T 20854-2025 English PDFUS$379.00 · In stock
Delivery: <= 4 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 20854-2025: Corrosion of metals and alloys - Accelerated testing involving cyclic exposure to salt mist, “dry” and “wet” conditions Status: Valid GB/T 20854: Historical versions
Basic dataStandard ID: GB/T 20854-2025 (GB/T20854-2025)Description (Translated English): Corrosion of metals and alloys - Accelerated testing involving cyclic exposure to salt mist, ��dry�� and ��wet�� conditions Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: H25 Classification of International Standard: 77.060 Word Count Estimation: 18,170 Date of Issue: 2025-04-25 Date of Implementation: 2025-11-01 Older Standard (superseded by this standard): GB/T 20854-2007 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration GB/T 20854-2025: Corrosion of metals and alloys - Accelerated testing involving cyclic exposure to salt mist, “dry”and“wet”conditions---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. ICS 77.060 CCSH25 National Standard of the People's Republic of China Replace GB/T 20854-2007 Corrosion of metals and alloys cyclically exposed to salt spray, Accelerated testing under "dry" and "wet" conditions (ISO 14993.2018, IDT) Released on 2025-04-25 2025-11-01 Implementation State Administration for Market Regulation The National Standardization Administration issued Table of contentsPreface III Introduction IV 1 Scope 1 2 Normative references 1 3 Terms and Definitions 1 4 Test solution 2 5 Test equipment 2 6 Sample 3 7 Sample placement 3 8 Test conditions 4 9 Testing Continuity 5 10 Test cycle 5 11 Handling of samples after testing 5 12 Test result evaluation 6 13 Test Report 6 Appendix A (Informative) Cyclic salt spray, "dry" and "wet" corrosion test equipment 7 Appendix B (Informative) Evaluation method for corrosiveness of test equipment 9 Appendix C (Normative) Preparation of organic coating samples for testing 11 Appendix D (Normative) Supplementary information on test organic coating samples 12 Reference 13ForewordThis document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for standardization work Part 1.Structure and drafting rules for standardization documents" Drafting is required. This document replaces GB/T 20854-2007 "Corrosion of metals and alloys cyclically exposed to salt spray, "dry" and "wet" conditions accelerated Compared with GB/T 20854-2007, in addition to structural adjustments and editorial changes, the main technical changes are as follows. a) Added “Terms and Definitions” (see Chapter 3); b) Changed "Concentration of test solution" (see 4.2, 3.2 of the.2007 edition); c) Changed the requirements for "sodium chloride for preparing solutions" (see 4.2, 3.2 of the.2007 edition); d) Added the requirement of “component protection” (see 5.1); e) Added the requirements for "test chamber" (see 5.2.1); f) Added the recommended pressure value for “spray device” (see 5.2.3); g) The requirements for “specimen” have been changed (see 6.1, 5.1 of the.2007 edition); h) Added “specimen placement” instead of the requirements for specimens (see 7.2); i) Added the “test condition” solution tank cover (see 8.6); j) The “Test Conditions” have been changed (see Table 1 in Chapter 8 and Table 1 in Chapter 7 of the.2007 edition); k) Changed "Continuity of testing" (see Chapter 9, Chapter 8 of the.2007 edition); l) Added “Overview of sample handling after testing” (see 11.1); m) Added "organic coating sample" (see 11.3); n) Changed "Evaluation of test results" [see Chapter 12c), Chapter 11c of the.2007 edition]; o) "Test Report" has been changed (see Chapter 13, Chapter 12 of the.2007 edition); p) Changed the “Cyclic salt spray, “dry” and “wet” corrosion test equipment” (see Appendix A, Appendix A of the.2007 edition); q) The “Evaluation Method of Corrosivity of Test Equipment” has been changed (see Appendix B, Appendix B of the.2007 Edition); r) Added the preparation of organic coating samples for testing (see Appendix C); s) Added additional information on the organic coating samples used in the test (see Appendix D). This document is equivalent to ISO 14993.2018 “Corrosion of metals and alloys by cyclic exposure to salt spray, “dry” and “wet” conditions”. Speed Test. Please note that some of the contents of this document may involve patents. The issuing organization of this document does not assume the responsibility for identifying patents. This document was proposed by the China Iron and Steel Association. This document is under the jurisdiction of the National Technical Committee on Steel Standardization (SAC/TC183). This document was drafted by. Institute of Metal Research, Chinese Academy of Sciences, Institute of Metallurgical Industry Information Standards, Hebei Hesteel Material Technology Research Institute Co., Ltd., Bengang Plate Co., Ltd., Beijing Zhongke Optical Analysis Science and Technology Research Institute, and Shenyang Anti-Rust Packaging Materials Co., Ltd. The main drafters of this document are. Wang Zhenyao, Cao Gongwang, Hou Jie, Ma Cheng, Liu Hongliang, Tian Zijian, Gao Junguang, Liu Yuwei, Li Qian, Zhang Caidong, Wang Yafen, Wang Chuan, Sun Menghan, Zhang Weixu, and Wang Rui. This document was first published in.2007 and this is the first revision.IntroductionWhether protected or not, the corrosion of metal materials is affected by many environmental factors, which mainly depend on the type of metal material and the type of environment. When designing a laboratory accelerated corrosion test, it is impossible to consider all environmental factors that affect corrosion. Therefore, the purpose of laboratory testing is to Simulate the effects of the most important factors that enhance corrosion of metallic materials. The accelerated corrosion test method described in this document is designed to simulate and increase the environmental exposure to outdoor salt contamination and accelerate corrosion. Designed for the impact of the atmosphere on metal materials. The test method involves cyclic exposure of the specimen to salt spray, "dry" and "wet" environments. This test is a comparative test and the test results cannot predict The long-term results of testing the corrosion resistance of the same metal materials used in this environment are not obtained. However, this method can still provide the results of exposure to the same test conditions. Valuable information on the relevant properties of materials in similar salt contaminated environments. Corrosion of metals and alloys cyclically exposed to salt spray, Accelerated testing under "dry" and "wet" conditions WARNING. This document may contain hazardous materials, procedures, and equipment. This document does not claim to address all safety issues associated with its use. It is the responsibility of the user of this document to establish safety and health practices and determine applicable regulatory requirements prior to use.1 ScopeThis document specifies the apparatus and test methods for accelerated corrosion testing of metallic materials for use outdoors in salt-contaminated environments. This document specifies the cyclic exposure of specimens to neutral salt spray, Test methods for "dry" and "wet" test environments. The type of specimen and exposure time are not specified in this document. Compared with conventional accelerated corrosion tests, such as the neutral salt spray test (NSS), the biggest advantage of this test is that it can better Corrosion now occurs in outdoor salt-contaminated environments. The accelerated corrosion tests in this document are applicable to. ---Metals and their alloys; ---Metallic covering (anodic and cathodic); ---Conversion covering layer; --- Anodic oxide coating; ---Organic coating on metal materials. Note. GB/T 31588.1 gives the test method for the coating to determine the resistance of the coating to various cyclic corrosion conditions (including resistance to moisture (including condensation of water on the specimen during humidity).2 Normative referencesThe contents of the following documents constitute essential clauses of this document through normative references in this document. For referenced documents without a date, only the version corresponding to that date applies to this document; for referenced documents without a date, the latest version (including all amendments) applies to This document. Note. GB/T 9271-2008 Standard test panels for paints and varnishes (ISO 1514.2004, MOD) ness) Note. GB/T 13452.2-2008 Determination of film thickness of paints and varnishes (ISO 2808.2007, IDT) ISO 4623-2.2016 Paints and varnishes - Filiform corrosion resistance of coatings on aluminium and aluminium alloys Note. GB/T 26323-2010 Paint and varnish coatings on aluminium and aluminium alloys - Filiform corrosion resistance test (ISO 4623-2.2003, MOD) Note. GB/T 10123-2022 Corrosion terminology for metals and alloys (ISO 8044.2020, IDT) ISO 17872 Guide for marking metal panels with scratches for corrosion testing of paints and varnishes ting) Note. GB/T 30786-2014 Guidelines for scratch marking of metal panels for corrosion testing of paints and varnishes (ISO 17872.2007, IDT) ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 20854-2025_English be delivered?Answer: Upon your order, we will start to translate GB/T 20854-2025_English as soon as possible, and keep you informed of the progress. The lead time is typically 2 ~ 4 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 20854-2025_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 20854-2025_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 20854-2025?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 20854-2025 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
