GB/T 19316-2025 English PDFUS$244.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 19316-2025: Small craft - Steering wheels Status: Valid GB/T 19316: Historical versions
Basic dataStandard ID: GB/T 19316-2025 (GB/T19316-2025)Description (Translated English): Small craft - Steering wheels Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: U37 Classification of International Standard: 47.080 Word Count Estimation: 12,126 Date of Issue: 2025-06-30 Date of Implementation: 2025-06-30 Older Standard (superseded by this standard): GB/T 19316-2008 Issuing agency(ies): State Administration for Market Regulation, China National Standardization Administration GB/T 19316-2025: Small craft - Steering wheels---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT19316-2025ICS 47.080 CCSU37 National Standard of the People's Republic of China Replaces GB/T 19316-2008 Boat steering wheel (ISO 23411.2020, IDT) Released on June 30, 2025 Implementation on June 30, 2025 State Administration for Market Regulation The National Standardization Administration issued Table of ContentsPreface III 1 Scope 1 2 Normative references 1 3 Terms and Definitions 1 4 General Requirements 2 5 Experiment 4 6 Fatigue test 7 References 8 Preface This document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for standardization work Part 1.Structure and drafting rules for standardization documents" Drafting. This document replaces GB/T 19316-2008 "Remote control steering system for small inboard motor water jet boats" and GB/T 19316- Compared with.2008, in addition to structural adjustments and editorial changes, the main technical changes are as follows. a) Several terms and their definitions such as steering mechanism, steering wheel diameter, steering wheel concavity, etc. are added (see Chapter 3); b) The steering gear, steering shaft and steering system in the “Structural requirements” have been deleted (see 4.2 to 4.4 of the.2008 edition); c) The content of "General Requirements" has been modified (see Chapter 4, 4.1 of the.2008 edition); d) The general requirements in "Steering test" are deleted (see 5.1 of the.2008 edition); e) Added the contents of “Test conditions”, “Mechanical properties test” and “Impact load test” (see 5.1 to 5.3); f) The scope and content of “Fatigue test” have been modified (see Chapter 6, 5.4 of the.2008 edition). This document is equivalent to ISO 23411.2020 "Small boat steering wheels". Please note that some of the contents of this document may involve patents. The issuing organization of this document does not assume the responsibility for identifying patents. This document is proposed and coordinated by the National Technical Committee for Standardization of Small Boats (SAC/TC241). This document was drafted by. The 708th Research Institute of China Shipbuilding Industry Corporation. The main drafters of this document are. Xia Jun, Fu Xiaohong, He Lin, Lu Shiping, Zhou Yilong, Hu Shihong, and Sun Suyue. The previous versions of this document and the documents it replaces are as follows. ---First published as GB/T 19316-2003 in.2003 and first revised in.2008. ---This is the second revision. Boat steering wheel 1 Scope This document specifies the design and testing requirements for small boat steering wheels. 2 Normative references The contents of the following documents constitute the essential clauses of this document through normative references in this document. For referenced documents without a date, only the version corresponding to that date applies to this document; for referenced documents without a date, the latest version (including all amendments) applies to This document. ISO 25197.2020 Small craft - Electrical/electronic control systems for steering, gear shifting and throttle 3 Terms and Definitions The following terms and definitions apply to this document. 3.1 steering mechanism A device equipped with a control element to transmit manual control force, and through this device the control force is transmitted to the steering mechanism. 3.2 After the test, the steering system has the ability to generate a force of no more than 27 N·m on the steering mechanism through the steering wheel or other normal operations. torque so that the steering system is capable of at least 90% of normal steering travel on each side of the neutral position. NOTE. This document does not specify the performance of steering systems for small craft underway, but is intended to provide quantitative limits for design and testing. 3.3 actual diameter actualdiameter Da The diameter of the circle formed by the outermost parts of the steering wheels. Note. See Figure 1. 3.4 steeringwheeldish The distance between the two horizontal planes of the steering wheel rim and the hub. Note. See Figure 1. 3.5 pinchpoint A position where a moving part is in contact with or so close to another part that the other object in that position could be cut or crushed. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 19316-2025_English be delivered?Answer: Upon your order, we will start to translate GB/T 19316-2025_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 19316-2025_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 19316-2025_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 19316-2025?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 19316-2025 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
