GB/T 18290.5-2015 English PDFUS$534.00 · In stock
Delivery: <= 4 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 18290.5-2015: Solderless connections -- Part 5: Press-in connections -- General requirements, test methods and practical guidance Status: Valid GB/T 18290.5: Historical versions
Basic dataStandard ID: GB/T 18290.5-2015 (GB/T18290.5-2015)Description (Translated English): Solderless connections -- Part 5: Press-in connections -- General requirements, test methods and practical guidance Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: L23 Classification of International Standard: 31.220.10 Word Count Estimation: 27,253 Date of Issue: 2015-12-31 Date of Implementation: 2016-07-01 Older Standard (superseded by this standard): GB/T 18290.5-2000 Regulation (derived from): State Standard Announcement 2015 No.43 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China GB/T 18290.5-2015: Solderless connections -- Part 5: Press-in connections -- General requirements, test methods and practical guidance---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Solderless connections - Part 5. Press-in connections - General requirements, test methods and practical guidance ICS 31.220.10 L23 National Standards of People's Republic of China Replacing GB/T 18290.5-2000 Solderless connections - Part 5. Press - in connections General requirements, test methods and practical guidance Solderlessconnections-Part 5. Press-inconnections- Generalrequirements, testmethodsandpracticalguidance (IEC 60352-5.2003, IDT) Issued on. 2015-12-31 2016-07-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released Table of ContentsPreface Ⅰ Introduction Ⅱ 1 Scope and purpose 1 2 Normative references 1 3 Terms and definitions 2 Requirement 3 4 5 Test 6 6 Use Guide 15 Appendix A (normative) solid press-fit terminations 21 References 22ForewordGB/T 18290 "solderless connection" consists of the following components. --- Part 1. solderless connection about connections - General requirements, test methods and practical guidance; --- Part 2. solderless connection crimped connections - General requirements, test methods and practical guidance; --- Part 3. solderless connector solderless accessible insulation displacement connections - General requirements, test methods and guidelines; --- Part 4. solderless connection untouchable solderless insulation displacement connections - General requirements, test methods and guidelines; --- Part 5. solderless connection push-in connections - General requirements, test methods and guidelines; --- Part 6. solderless connector insulation displacement connections - General requirements, test methods and guidelines; --- Part 7. solderless connection spring clamp connections - General requirements, test methods and guidelines; --- Part 8. solderless connection clamping mount connections - General requirements, test methods and practical guidance. This section GB/T 18290 Part 5. This section drafted in accordance with GB/T 1.1-2009 given rules. This Part replaces GB/T 18290.5-2000 "Solderless connections - Part 5. Solderless press-in connections - General requirements, test methods and Guidelines for the use. " Section compared with the GB/T 18290.5-2000, major changes in the following. --- Adds two definitions of "parts" and "sample" (see Chapter 3); --- Amendment plated through hole plated size (see 4.4.3.2); --- Increase the "manufacturer's specification" (see 4.6); --- The "type test" to "test and measurement methods" (see 5.2); --- Added "microscopic cross-section" and "replacement (maintenance)" (see 5.2.2); --- Added "high temperature" test, "Industrial Atmospheric Corrosion" test removed to "Flowing mixed gas corrosion" in place of the test (see 5.2.4); --- The "basic test schedule" and "full test schedule" to "identification test list" and "application test schedule", and Sample preparation was adjusted (see 5.3); --- Added Appendix A. This section uses the translation method is equivalent to using IEC 60352-5.2003 "solderless connection Part 5. Press - in connections - General requirements, test Methods and practical guidance. " For ease of use, this section made the following editorial changes. --- Remove the imperial units. Please note that some of the content of this document may involve patents. Release mechanism of the present document does not assume responsibility for the identification of these patents. This part is proposed by the Ministry of Industry and Information Technology of the People's Republic of China. This section is under the jurisdiction of the National electronic equipment Electromechanical components for Standardization Technical Committee (SAC/TC166). This part by the Guizhou Space Appliance Co., Ltd., Shenzhen Electronics Co. Alto, responsible for China Electronics Standardization Institute Drafted. The main drafters of this section. MING -, Liao Chaoshun, Qiu Rongbang, Austrian Chen Ding Ran. This part of the standard replaces the previous editions are. --- GB/T 18290.5-2000.IntroductionThis section includes requirements, tests and practical guidance information, and give two test schedule. --- Identification test schedule. for a single push-in connection (press-in area). Taking into account the requirements of Chapter 4, provided by the press-in area to the manufacturer specification test (see 4.6). Identification of components used in press-in area is independent. --- Application test schedule. for press-fit connector element portion has passed the test schedule identification identification. Test sequence element in the implementation of the assessment is the push-performance connections. Since the press-in area manufacturer must provide the main content of the required identification, so throughout this section referred to as "factory." IEC Guide 109.1995 to promote products to reduce the impact on the natural environment in the product life cycle. This section of the timber to allow some The material used may have a negative impact on the environment. In order to guide technically replace these materials, which will disappear in this section. Solderless connections - Part 5. Press - in connections General requirements, test methods and practical guidance1 Scope and purposeGB/T 18290 apply to this part of solderless press-in connection, this connection is used for communications equipment and electronic devices employing similar techniques. Preparation of. Press-fit connection with the embedded double-sided or multilayer PCB plated through-hole press-fit terminations. Further, in order to obtain a stable electrical connection under specified environmental conditions, in addition to the test procedure, this section also provides for the use from industrial solid Some international experience data departure. The purpose of this section is to determine the suitability of press-fit connections under specified mechanical, electrical and atmospheric conditions. Only in this section is pressed into the flexible regions were identified. The use of solid press-in area of \u200b\u200bthe information given in Appendix A.2 Normative referencesThe following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document. GB/T 2421.1-2008 Environmental testing for electric and electronic products overview and guidance (IEC 60068-1. 1988, IDT) GB/T 4210-2001 Electrotechnical terminology Electromechanical components for electronic equipment [idt IEC 60050 (581). 1978] GB/T 5095.1-1997 electronic equipment - Basic testing procedures and measuring methods - Electromechanical components - Part 1. General (idt IEC 60512-1.1994) GB/T 5095.2-1997 electronic equipment - Basic testing procedures and measuring methods - Electromechanical components - Part 2. General examination, electrical Continuity and contact resistance tests, insulation tests and voltage stress test (idt IEC 60512-2. 1985) GB/T 5095.4-1997 electronic equipment - Basic testing procedures and measuring methods - Electromechanical components - Part 4. Dynamic stress test Test (idt IEC 60512.4. 1976) GB/T 5095.6-1997 Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Part 6. Climatic tests and Soldering tests (idt IEC 60512.6. 1984) GB/T 5095.11-1997 electronic equipment - Basic testing procedures and measuring methods - Electromechanical components - Part 11. Climatic tests (Idt IEC 60512.11-1.1995, idt IEC 60512.11-7.1996, idt IEC 60512.11-8.1995) IEC 60249-2-4. 1987 printed circuit substrates - Part 2. Specifications Specification 4. General Purpose copper clad epoxy glass cloth laminated board (Basematerialsforprintedcircuits-Part 2. Specifications-SpecificationNO.4. Epoxidewovenglass fabriccopper-cladlaminatedsheet, generalpurposegrade) Amendments 3 (1993) (Amendment3) IEC 60249-2-5. 1987 printed circuit substrates - Part 2. Specifications Specification 5. Flame retardant epoxy glass cloth copper clad laminate (vertical Direct burning test) [Basematerialsforprintedcircuits-Part 2. Specifications-SpecificationNO.5. Epoxide wovenglassfabriccopper-cladlaminatedsheetofdefinedflammability (verticalburningtest)] Amendments 3 (1993) (Amendment3) Amendments 4 (1994) (Amendment4) IEC 60249-2-11. 1987 general-purpose thin copper clad epoxy glass cloth laminate (manufactured multilayer printed boards) (Basemate- ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 18290.5-2015_English be delivered?Answer: Upon your order, we will start to translate GB/T 18290.5-2015_English as soon as possible, and keep you informed of the progress. The lead time is typically 2 ~ 4 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 18290.5-2015_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 18290.5-2015_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 18290.5-2015?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 18290.5-2015 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
