GB/T 18290.2-2015 English PDFUS$854.00 · In stock
Delivery: <= 5 days. True-PDF full-copy in English will be manually translated and delivered via email. GB/T 18290.2-2015: Solderless connections -- Part 2: Crimped connections -- General requirements, test methods and practical guidance Status: Valid GB/T 18290.2: Historical versions
Basic dataStandard ID: GB/T 18290.2-2015 (GB/T18290.2-2015)Description (Translated English): Solderless connections -- Part 2: Crimped connections -- General requirements, test methods and practical guidance Sector / Industry: National Standard (Recommended) Classification of Chinese Standard: L23 Classification of International Standard: 31.220.10 Word Count Estimation: 43,441 Date of Issue: 2015-12-31 Date of Implementation: 2016-07-01 Older Standard (superseded by this standard): GB/T 18290.2-2000 Regulation (derived from): State Standard Announcement 2015 No.43 Issuing agency(ies): General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China GB/T 18290.2-2015: Solderless connections -- Part 2: Crimped connections -- General requirements, test methods and practical guidance---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Solderless connections - Part 2. Crimped connections - General requirements, test methods and practical guidance ICS 31.220.10 L23 National Standards of People's Republic of China Replacing GB/T 18290.2-2000 Solderless connections - Part 2. Crimp connection General requirements, test methods and practical guidance Solderlessconnections-Part 2. Crimpedconnections- Generalrequirements, testmethodsandpracticalguidance (IEC 60352-2.2006, IDT) Issued on. 2015-12-31 2016-07-01 implementation Administration of Quality Supervision, Inspection and Quarantine of People's Republic of China Standardization Administration of China released Table of ContentsPreface Ⅰ Introduction Ⅱ 1 Scope and purpose 1 2 Normative references 1 3 Terms and definitions Requirement 3 4 5 Test 5 6 crimped connections - General Information 21 7 Tool Data 21 8 crimp barrel 22 Profile 9 wire data 25 10 connection information 27 11 crimping process 30 12 correct crimp connection (Additional Information) 32 13 open barrel crimp contacts crimp defects 34 About 14 pieces of multi-contact connector crimp contacts Description 36 15 Note 38ForewordGB/T 18290 "solderless connection" consists of the following components. --- Part 1. solderless connection about connections - General requirements, test methods and practical guidance; --- Part 2. solderless connection crimped connections - General requirements, test methods and practical guidance; --- Part 3. solderless connector solderless accessible insulation displacement connections - General requirements, test methods and guidelines; --- Part 4. solderless connection untouchable solderless insulation displacement connections - General requirements, test methods and guidelines; --- Part 5. solderless connection push-in connections - General requirements, test methods and guidelines; --- Part 6. solderless connector insulation displacement connections - General requirements, test methods and guidelines; --- Part 7. solderless connection spring clamp connections - General requirements, test methods and guidelines; --- Part 8. solderless connection clamping mount connections - General requirements, test methods and practical guidance. This section GB/T 18290 Part 2. This section drafted in accordance with GB/T 1.1-2009 given rules. This Part replaces GB/T 18290.2-2000 "Solderless connections Part 2. Solderless crimped connections - General requirements, test methods and make With the guidelines. " Section compared with the GB/T 18290.2-2000, major changes in the following. --- Reg No. reclassified (see Chapter 4, Chapter 5 of the 2000 edition, Chapter 6, Chapter 7, Chapter 8 and Chapter 9); Materials --- crimp barrel requirements from a single Vickers hardness adds more strength requirements (see 4.3.1); --- Tin - lead alloy has been replaced by tin alloy, in order to meet the RoHS directive, other coating materials, such as nickel, may also be used, as long as the card Ming adapted (see 4.3.3); --- Increasing the recovery test item (see 5.1.4); --- Deletion of other materials (see Table 2); --- Change between two samples wire length is "Min 150mm" to meet regional requirements (see 5.2.4.5 and Figure 7); --- Remove the old product size (2000 version 15.4). This section uses the translation method is equivalent to using IEC 60352-2.2006 "Solderless connections - Part 2. crimped connections - General requirements, test Methods and practical guidance. " For ease of use, this section for the following editorial changes. --- Remove the imperial units. Please note that some of the content of this document may involve patents. Release mechanism of the present document does not assume responsibility for the identification of these patents. This part is proposed by the Ministry of Industry and Information Technology of the People's Republic of China. This section is under the jurisdiction of the National electronic equipment Electromechanical components for Standardization Technical Committee (SAC/TC166). This section is drafted. Guizhou Space Appliance Co., Ltd., Shenzhen Dinuo Wei Technology Co., Ltd., China Electronics Standardization Institute Study hospital. The main drafters of this section. Lee Lexus, Liao Chaoshun, Shao Zhenghua, Austrian Chen Ding Ran. This part of the standard replaces the previous editions are. GB/T 18290.2-2000.IntroductionThis section includes requirements, tests and practical guidance information, and give two test schedule. --- Basic test schedule. for compliance with all the requirements in Chapter 4 of solderless crimped connections; --- Comprehensive test schedule. for not fully comply with Chapter 4 solderless crimped connections all the requirements, for example, with a solid wire pressure Then, different materials. IEC Guide 109.1995 to promote products to reduce the impact on the natural environment in the product life cycle. This section of the timber to allow some The material used may have a negative impact on the environment. In order to guide technically replace these materials, which will disappear in this section. Solderless connections - Part 2. Crimp connection General requirements, test methods and practical guidance1 Scope and purposeGB/T 18290 apply to this part of solderless crimped connections, connect the wire strands or cross-sectional area of \u200b\u200b0.05mm2 ~ 10mm2 Diameter of 0.25mm ~ 3.6mm solid lines and the appropriate design to uninsulated or pre-insulated crimp barrel solderless crimped connections. This even Access to communications equipment and electronic devices using similar technology in. In order to obtain stable under the environmental conditions of the electrical connections, except in the test program, this section also provides for the use from industrial solid Some international experience data departure. Note. This section does not apply to coaxial cable crimping. The purpose of this section is to determine under specified mechanical, electrical and atmospheric conditions solderless pressure applicability Joints. When connected to work A design or process is not the same, there is provided a method comparable test results.2 Normative referencesThe following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including all amendments creators) are applicable to this document. GB/T 2421.1-2008 Environmental testing for electric and electronic products overview and guidance (IEC 60068-1. 1988, IDT) GB/T 4210-2001 Electrotechnical terminology Electromechanical components for electronic equipment (idt IEC 60050 (581). 1978) IEC 60189-3. 1988 are PVC insulated and PVC sheathed low-frequency cables and wires - Part 3. solid or stranded conductor Equipment wire with PVC single, double, triple insulated protection (Low-frequencycablesandwireswithPVCinsulation andPVCsheath-Part 3. Equipmentwireswithsolidorstrandedconductor, PVCinsulated, insingles, pairsandtriples) IEC 60512 (all parts), Connectors for electronic equipment - Tests and measurements (Connectorsforelectronicequipment- Testsandmeasurements) IEC 60512-1-100.2001 Connectors for electronic equipment - Tests and measurements - Part 1-100. General - Applicable Publications (Connectorsforelectronicequipment-Testsand measurements-Part 1-100. General-Applicable publcations) IEC 60760. 1989 flat quick-connect terminals (Flat, quick-connectterminations) Amendments 1 (1993) (Amendment1) ISO 6892.1998 metal material tensile test at ambient temperature (Metalicmaterials-Tensiletestingatambi- enttemperature)3 Terms and DefinitionsGB/T 4210-2001, IEC 60512-1-100.2001 and defined the following terms and definitions apply to this document. 3.1 Crimp tube crimpbarrel Designed to accommodate one or more wires crimping tool and crimping wire barrel. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of GB/T 18290.2-2015_English be delivered?Answer: Upon your order, we will start to translate GB/T 18290.2-2015_English as soon as possible, and keep you informed of the progress. The lead time is typically 3 ~ 5 working days. The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of GB/T 18290.2-2015_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 18290.2-2015_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version GB/T 18290.2-2015?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 18290.2-2015 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
