GB/T 16935.4-2011 PDF EnglishUS$285.00 · In stock · Download in 9 seconds
GB/T 16935.4-2011: Insulation coordination for equipment within low-voltage systems -- Part 4: Consideration of high-frequency voltage stress Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 16935.4-2011: Insulation coordination for equipment within low-voltage systems -- Part 4: Consideration of high-frequency voltage stress---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT16935.4-2011 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 29.120 K 30 GB/T 16935.4-2011 / IEC 60664-4.2005 Insulation coordination for equipment within low-voltage systems - Part 4.Consideration of high-frequency voltage stress (IEC 60664-4.2005, IDT) Issued on. DECEMBER 30, 2011 Implemented on. MAY 1, 2012 Issued by. General Administration of Quality Supervision, Inspection and Quarantine; Standardization Administration Committee. Table of ContentsForeword... 3 Introduction... 4 1 Scope... 5 2 Normative references... 6 3 Terms and definitions... 6 4 Clearances... 7 5 Creepage distances... 12 6 Solid insulation... 15 7 High-frequency testing... 17 8 Non sinusoidal voltages... 22 Annex A (Informative) Insulation characteristics of clearances at high-frequency voltages... 25 Annex B (Informative) Insulation characteristics of creepage distances... 32 at high-frequency voltages... 32 Annex C (Informative) Insulation characteristics of solid insulation at high-frequency voltages... 36 Annex D (Normative) Testing of insulation at high-frequency voltages... 44 Annex E (Informative) Insulation stressed with non-sinusoidal high-frequency voltages... 58 Annex F (Informative) Dimensioning diagrams... 63 Bibliography... 65ForewordGB/T 16935 Insulation coordination for equipment within low-voltage systems consists of the following 4 parts. - Part 1.Principles, requirements and tests; - Part 3.Use of coating, potting or molding for protection against pollution; - Part 4.Consideration of high-frequency voltage stress; - Part 5.Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm. This Part is Part 4 of GB/T 16935. This Part was drafted in accordance with the rules given in GB/T 1.1-2009. This Part uses translation method of identically adopt IEC 60664-4.2005 Insulation coordination for equipment within low-voltage systems - Part 4. Consideration of high-frequency voltage stress. This Part shall be used in conjunction with GB/T 16935.1-2008 Insulation coordination for equipment within low-voltage systems - Part 1.Principles requirements and tests (IEC 60664-1.2007, IDT) and GB/T 16935.5-2008 Insulation coordination for equipment within low-voltage systems - Part 5. Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm (IEC 60664-5.2007, IDT). This Part was proposed by China Electrical Equipment Industrial Association. This Part shall be under the jurisdiction of National Technical Committee on Low-voltage Equipment with Insulation of Standardization Administration of China (SAC/TC 417). The drafting organization of this Part. Shanghai Electric Science Research Institute. Main drafters of this Part. Zhang Jianbing, Bao Ge, Wu Qingyun.1 ScopeThis Part of GB/T 16935 specifies the requirements for clearances, creepage distances and solid insulation for equipment based upon their performance criteria. It includes methods of electric testing with respect to insulation coordination.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60112.2003, Method for determining the comparative and the proof tracking indices of solid insulating materials under moist conditions3 Terms and definitionsFor the purposes of this document, the terms and definitions given in IEC 60664-1, as well as the following terms and definitions, apply. generic term for both partial discharge inception voltage Ui and partial discharge extinction voltage Ue4 ClearancesAs a conclusion from A.2.1, the critical frequency fcrit, at which the reduction of the breakdown voltage occurs, depends upon the value of the clearance as follows.5 Creepage distancesMeasuring data for three different frequency ranges up to 100 kHz, up to 1 MHz and up to 3 MHz are shown in Figure 2 (measurement) together with limiting curves (dimensioning).6 Solid insulationThe following method of dimensioning can be used instead of high-frequency testing according to Clause 7.7 High-frequency testingIf not otherwise specified by technical committees, the test shall be performed with a new test specimen. Conditioning of the specimen by temperature and humidity treatment is intended to No breakdown shall occur during the test duration. After the test, no visible damage (burning, melting etc.) shall occur.8 Non sinusoidal voltagesFor dimensioning of the clearances, the peak value of the non-sinusoidal voltage and the repetition frequency of the voltage peaks are relevant. In the case of a maximum voltage frequency of 10 MHz, if the field strength is approximately uniform and no voids or air gaps are present in between the solid insulation, the dimensioning procedure described in 6.3 may be applied instead of testing.Annex A(Informative) Insulation characteristics of clearances at high-frequency voltages Breakdown of clearances usually occur in less than one microsecond. With respect to that time scale, an a.c. voltage of power frequency has an essentially constant amplitude. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 16935.4-2011 be delivered?Answer: The full copy PDF of English version of GB/T 16935.4-2011 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 16935.4-2011_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 16935.4-2011_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 16935.4-2011 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 16935.4-2011?A step-by-step guide to download PDF of GB/T 16935.4-2011_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 16935.4-2011". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
