GB/T 16935.5-2008 PDF EnglishUS$145.00 · In stock · Download in 9 seconds
GB/T 16935.5-2008: Insulation coordination for equipment within low-voltage systems -- Part 5: Comprehensive method for determining clearances and creepage distances equal to or less than 2mm Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure Status: Valid
Similar standardsGB/T 16935.5-2008: Insulation coordination for equipment within low-voltage systems -- Part 5: Comprehensive method for determining clearances and creepage distances equal to or less than 2mm---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT16935.5-2008 GB NATIONAL STANDARD OF THE PEOPLE’S REPUBLIC OF CHINA ICS 29.120 K 30 GB/T 16935.5-2008 / IEC 60664-5.2007 Insulation coordination for equipment within low- voltage systems - Part 5.Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm (IEC 60664-5.2007, IDT) Issued on. JULY 16, 2008 Implemented on. APRIL 01, 2009 Issued by. General Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China; Standardization Administration of the People’s Republic of China. Table of ContentsForeword... 4 Introduction... 5 1 Scope and object... 7 2 Normative references... 8 3 Terms and definitions... 9 4 Fundamentals of clearance and creepage distance dimensioning... 9 4.1 Introductory remark... 9 4.2 Basic principles... 9 4.3 Voltages and voltage ratings... 10 4.4 Frequency... 13 4.5 Time under voltage stress... 13 4.6 Pollution... 13 4.7 Information supplied with the equipment... 14 4.8 Insulating material... 14 5 Requirements and dimensioning procedures... 16 5.1 General... 16 5.2 Dimensioning of clearances... 16 5.3 Dimensioning of creepage distances... 22 5.4 Requirements for design of solid insulation... 30 6 Tests and measurements... 33 6.1 Tests... 33 6.2 Measurement of creepage distances and clearances... 42 Annex A (informative) Dimensioning to maintain minimum insulation resistance ... 43 Annex B (normative) |Water adsorption test... 46 Annex C (informative) Dimensioning diagrams... 50 Annex D (informative) Withstand voltage test for creepage distance under humid conditions... 53 Bibliography... 54ForewordGB/T 16935 “Insulation coordination for equipment within low-voltage systems” consists of 5 parts. - Part 1.Principles, requirements and tests; - Part 2.Application guide; - Part 3.Use of coating, potting or moulding for protection against pollution; - Part 4.Consideration of high-frequency voltage stress; - Part 5.Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm. This Part is Part 5 of GB/T 16935. This Part is identical to IEC 60664-5.2007 “Insulation coordination for equipment within low-voltage systems - Part 5.Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm” (English version). For ease of use, this Part has made the following editorial modifications. a) DELETE the foreword of the international standard; b) SUPPLEMENT GB/T 17045-2006, GB/T 17627.1-1998, GB/T 17627.2-1998, IEC 60068, IEC 60364-5-51.2005 and IEC 60664-4.1997 (because they are referenced in the article) in Clause 2 “Normative references”. In this Part, Annex B is normative, Annex A, Annex C and Annex D are informative. This Part is proposed by China Electrical Equipment Industry Association. This Part is under the jurisdiction of National Technical Committee on Low Voltage Equipment Insulation Coordination of Standardization Administration of China (SAC/TC 417). Responsible drafting organization of this Part. Shanghai Electric Apparatus Research Institute (Group) Co., Ltd. Participating drafting organization of this Part. Schneider Electric (China) Investment Co., Ltd. Main drafters of this Part. Huang Jingye, Liu Jinyan, Wu Qingyun. Participating drafter of this Part. Liu Zhenzhong.1 Scope and objectThis Part of GB/T 16935 specifies the dimensioning of clearances and creepage distances for spacings equal to or less than 2 mm for printed wiring board and equivalent constructions, where the clearance and the creepage distance are identical and are along the surface of solid insulation, such as the paths described in 6.2 of Part 12) (Examples 1, 5 and 11).2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. Clause 2 of Part 1 is applicable, as well as the following. GB/T 4798.3-2007 Environmental conditions existing in the application of electric and electronic products - Section 3.Stationary use at weather-protected locations (IEC 60721-3-3.2002, MOD)3 Terms and definitionsFor the purposes of this document, the following terms and definitions, in addition to those given in GB/T 16935.1-2008, apply. Value of the relative humidity when the impulse withstand voltage of a creepage distance has dropped to 95 % of the value that was measured at 70 % relative humidity.4 Fundamentals of clearance and creepage distance dimensioningThe micro-environmental conditions for the insulation shall be taken into account. They depend primarily on the macro-environmental conditions in which the equipment is located and, in many cases, the environments are identical.5 Requirements and dimensioning proceduresValues for clearances in Table 2 for case B are only applicable for homogeneous fields. They can only be used where the shape and arrangement of the conductive parts is designed to achieve an electric field having an essentially constant voltage gradient. Subclause 5.3.3.7 of Part 1 is applicable.6 Tests and measurementsIf the withstand against steady-state voltages, recurring peak voltages or temporary overvoltages according to 5.2 is decisive for the dimensioning of clearances, and if those clearances are smaller than the case A values of Table 3, an a.c. voltage test according to the test in 6.1.2.2.2.2 of Part 1 is required. For the test conditions, technical committees shall specify temperature and humidity values.Annex A(informative) Dimensioning to maintain minimum insulation resistance This annex gives information on the dimensioning of creepage distances in order to maintain adequate insulation resistance for r.m.s. voltages up to 10 000 V, which relate to creepage distances up to 250 mm.Annex B(normative) |Water adsorption test For the dimensioning of creepage distances with respect to flashover, the water adsorption characteristics of the insulating material are relevant. According to the impulse withstand capability of the surfaces of the various insulating materials under humidity, the water adsorption groups WAG1, WAG2, WAG3 and WAG4 have been established. ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of GB/T 16935.5-2008 be delivered?Answer: The full copy PDF of English version of GB/T 16935.5-2008 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of GB/T 16935.5-2008_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 16935.5-2008_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 16935.5-2008 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of GB/T 16935.5-2008?A step-by-step guide to download PDF of GB/T 16935.5-2008_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "GB/T 16935.5-2008". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
