US$189.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email.
GB 29217-2012: Food additive cyclamic acid calcium
Status: Valid
| Standard ID | USD | BUY PDF | Lead-Days | Standard Title (Description) | Status |
| GB 29217-2012 | 189 |
Add to Cart
|
3 days
|
Food additive cyclamic acid calcium
| Valid |
Basic data
Standard ID: GB 29217-2012 (GB29217-2012)
Description (Translated English): Food additive cyclamic acid calcium
Sector / Industry: National Standard
Classification of Chinese Standard: X40
Classification of International Standard: 67.220.20
Word Count Estimation: 8,830
Regulation (derived from): Ministry of Health Bulletin 2012 No. 23
Issuing agency(ies): Ministry of Health of the People's Republic of China
Summary: This Chinese standard applies to cyclohexylamine and amino acid as the raw material reacts after cyclohexyl sulfamic acid with calcium hydroxide role in the system of food additives cyclohexyl sulfamic acid calcium.
GB 29217-2012: Food additive cyclamic acid calcium
---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.
Food additive cyclamic acid calcium
National Standards of People's Republic of China
National standards for food safety
Food additives Sodium cyclohexyl sulfamate
2012-12-25 release
2013-01-25 Implementation
Issued by the Ministry of Health of the People's Republic of China
National standards for food safety
Food additives Sodium cyclohexyl sulfamate
1 Scope
This standard applies to cyclohexylamine and sulfamic acid as raw materials to produce cyclohexyl sulfamate and calcium hydroxide after the role of the resulting food
Ingredients Cyclohexylaminosulfonate.
2 molecular formula, structural formula and relative molecular mass
2.1 Molecular formula
C12H24CaN2O6S2 · nH2O (n = 2 or 4)
2.2 Structural formula
[NHSO3] 2Ca · nH2O
2.3 Relative molecular mass
Dihydrate crystal products. 432.57 (according to the.2007 international relative atomic mass)
Four water crystal products. 468.60 (according to the.2007 international relative atomic mass)
3 technical requirements
3.1 sensory requirements
Shall comply with the provisions of Table 1.
Table 1 sensory requirements
The project requires a test method
Color white
State granular or powdered crystals
Take appropriate sample, placed in a clean, dry white porcelain dish, in the self
Under the light, the visual observation of color and state
3.2 Physical and chemical indicators
Shall comply with the provisions of Table 2.
Table 2 Physical and chemical indicators
project
index
Dihydrate crystal products four crystal products
Testing method
(Based on dry basis) content, w /% 98.0 to 101.0 Appendix A, A.4
Dry reduction, w /% ≤ 9.5 16.5 Appendix A, A.5
Cyclohexylamine/(mg/kg) ≤ 25 Appendix A A.6
Dicyclohexylamine was tested in Appendix A, A.7
Lead (Pb)/(mg/kg) ≤ 1 Appendix A A.8
Appendix A
Testing method
A.1 Warning
The test procedure specifies that some of the test procedures may lead to dangerous conditions and that the operator should take appropriate safety and protective measures.
A.2 General provisions
Unless otherwise stated, only the reagents identified as analytical reagents and the tertiary water specified in GB/T 6682-2008 are used in the analysis.
Standard titration solution used in the test method, standard solution for the determination of impurities, preparations and articles, in the absence of other requirements,
GB/T 601, GB/T 602 and GB/T 603. The solution used refers to the aqueous solution when no other requirements are indicated.
A.3 Identification test
A.3.1 Reagents and materials
A.3.1.1 Sodium nitrite solution. 100 g/L.
A.3.1.2 Hydrochloric acid solution. 1 3.
A.3.1.3 barium chloride solution. 50 g/L.
A.3.2 Identification method
A.3.2.1 Weigh about 1 g of sample, dissolve in water and make it into 100 mL as sample solution. Take 10mL of the test solution, add 1mL of hydrochloric acid dissolved
Liquid and 1mL barium chloride solution mixture, observe the solution should be transparent; then add 1mL sodium nitrite solution to generate white precipitation and escape
gas.
A.3.2.2 Take the wire into the appropriate amount of sample, burn in a colorless flame, the flame was red.
A.4 Determination of calcium hexyl sulfamate (in dry basis) content
A.4.1 Methodological Summary
After the reaction of calcium cyclohexylsulfamate with sodium nitrite is complete, excess sodium nitrite reacts with potassium iodide under acidic conditions to form iodine, iodine
Case of starch blue. The content of calcium cyclohexyl sulfamate was calculated from the volume of the titration solution of sodium nitrite standard.
A.4.2 Reagents and materials
A.4.2.1 Hydrochloric acid solution. 1 1.
A.4.2.2 Starch Potassium Iodide Test Paper.
A.4.2.3 standard titration solution of sodium nitrite. c (NaNO2) = 0.1mol/L.
A.4.3 Analysis steps
A.4.3.1 Weigh 0.4g for 2h after drying at 140 ° C and just 0.4g in the condenser just cooled to room temperature, accurate to 0.0002g in 250mL
Beaker.
A.4.3.2 Add 50 mL of water and 5 mL of hydrochloric acid solution to dissolve.
A.4.3.3 titration with sodium nitrite standard titration, titration to the final 1mL titration solution should be added dropwise until the glass rod
Dipped in 1 drop solution on the starch potassium iodide test paper immediately appeared blue, when the titration is complete, the drip maintained for 1min can still reproduce the end of the current
As indicated by the titration end point, the volume of the standard titration solution of sodium nitrite consumed is recorded.
A.4.3.4 At the same time as the determination, the same amount of reagent solution was used as a blank test in the same procedure as in the measurement,
Record the consumption volume V0.
A.4.4 Calculation of results
The mass fraction w1 of calcium (based on dry basis) of cyclohexylsulfamate is calculated according to formula (A.1)
w1 =
(V-V0) cM
m x 1000 x 100%
(A.1)
Where.
V - volume of sodium nitrite standard titration solution in milliliters (mL);
V0 --- blank consumption of sodium nitrite standard titration solution volume, in milliliters (mL);
c - the exact value of the concentration of sodium nitrite standard titration solution in moles per liter (mol/L);
m - the quality of the sample, in grams (g);
1000 --- conversion factor;
M - the molar mass of calcium cyclohexylsulfamate in grams per mole (g/mol) (M = 198.27).
The arithmetic mean of the results of two parallel measurements is the result of the report. The absolute difference between the two parallel determinations is not more than 0.40%.
A.5 Determination of dry reduction
A.5.1 Analysis steps
Approximately 2.0 g of the sample was weighed to 0.0002 g and placed in a preheated flask at 140 ° C ± 2 ° C to a constant mass. in
140 ℃ ± 2 ℃ constant temperature drying oven for 2h, placed in a dryer for 30min cooling.
A.5.2 Calculation of results
The mass fraction w2 of the drying reduction is calculated according to the formula (A.2)
w2 =
m1-m2
m x 100%
(A.2)
Where.
m - the mass of the sample before drying, in grams (g);
m1 --- the quality of the flask and the sample before drying, in grams (g);
m2 --- Weigh the quality of the bottle and the sample after drying, in grams (g).
The arithmetic mean of the results of two parallel measurements is the result of the report. The absolute difference between the two parallel determinations is not more than 0.20%.
A.6 Determination of cyclohexylamine
A.6.1 Reagents and materials
A.6.1.1 anhydrous sodium sulfate.
A.6.1.2 Alkaline ethylenediaminetetraacetic acid disodium solution. Weigh 100g of ethylenediamine tetraacetic acid and 34g of sodium hydroxide, add water and dissolve it.
Water diluted to 1000 mL.
A.6.1.3 methyl orange boric acid solution. Weigh 2g of methyl orange and boric acid 35g, add water 1000mL, on the water bath to heat it to dissolve
More than 24 hours. Filter before use.
A.6.1.4 Mixture of Trichloromethane and n-Butanol. 20 1.
A.6.1.5 Mixture of Methanol and Sulfuric Acid. 50 1.
A.6.1.6 Cyclohexylamine standard solution. 0.0025 mg of cyclohexylamine per milliliter. Weigh the cyclohexylamine 0.1g, accurate to 0.0002g, set
100mL volumetric flask, add 50mL of water and hydrochloric acid 0.5mL, dissolved and diluted with water to the mark, shake. Accurately measure 5.0mL, placed on
Another 100mL volumetric flask diluted with water to the mark, shake. Accurately measure the dilution of 5.0mL set 100mL volumetric flask, with water
Dilute to the scale, shake it.
A.6.2 Analysis steps
Weigh 10.0g sample, accurate to 0.01g, dissolved in about 60mL water, placed in 100mL volumetric flask, diluted with water to the mark, shake
uniform. Accurately absorb the solution and cyclohexylamine standard solution of 10.0mL, were placed in two 60mL separatory funnel, respectively, by adding
Alkaline ethylenediamine tetraacetic acid disodium salt solution 10.0mL, chloroform and n-butanol mixture 15.0mL, shaking 2min, standing, take trichloride
Methane layer, the amount of chloroform extraction of 10.0mL, placed in the other two 60mL separatory funnel, each adding methyl orange boric acid solution
2.0mL, shake 2min, standing, take the chloroform layer, add anhydrous sodium sulfate 1g, shaking, standing, the amount of chloroform solution 5.0mL,
Placed in the color tube, the addition of methanol and sulfuric acid mixture solution 0.5mL, shake. The color of the sample solution should not be deeper than the standard. With spectrophotometry
Measurements and standard absorbance. at 520nm wavelength, with chloroform correction of zero, the solution were moved into 1cm cuvette,
Test results The sample absorbance should not be greater than the standard absorbance.
A.7 Determination of bicyclohexylamine
A.7.1 Reagents and materials
A.7.1.1 Trichloromethane. washed three times with water, each time the amount of water for trichloromethane 1/3, the trichloromethane layer for the determination of.
A.7.1.2 Sodium hydroxide solution. 40 g/L.
A.7.1.3 Reagent A. Weigh 50mg of bromophenol blue, add water 60mL, add sodium bicarbonate solution (8.4g/L) 10mL, stirring to dissolve,
In hydrochloric acid solution (1 11) adjusted to pH 4.0, diluted with water to 100mL, shake, stored in a cool dark place, 48h use.
A.7.1.4 Reagent B. Take hydrochloric acid solution (1 11).200mL, glacial acetic acid 166mL in 1000mL volumetric flask, diluted with water
Degree, shake well.
A.7.2 Analysis steps
A.7.2.1 Weigh the sample 10.0g, accurate to 0.01g, in 250mL separatory funnel, add alkaline ethylenediamine tetraacetic acid disodium solution
(A.6.1.2) 100 mL to dissolve, and take 100 mL of basic ethylenediamine tetraacetic acid disodium solution (A.6.1.2) in another separatory funnel
Blank test.
A.7.2.2 Each 10 mL of sodium hydroxide solution was added and then extracted with 10 mL, 10 mL, 5 mL of trichloromethane, respectively
And the chloroform extraction layer is in the other two separatory funnels.
A.7.2.3 add 100mL water, 3mL reagent B, 1mL reagent A, shaking 3min dark place for 30min, after standing stratification, the separation
Trichloromethane was added to a 25 mL test tube and trichloromethane was added to 25 mL.
A.7.2.4 At 410 nm wavelength, adjust the blank and the absorbance of the sample solution with a 5 cm cuvette and zero the chloroform.
A.7.2.5 The difference between the sample solution and the blank absorbance is not greater than 0.15 for the pass test.
A.8 Determination of lead (Pb)
A.8.1 Colorimetric method (Arbitration law)
According to GB/T 5009.75 for the determination (the sample may not be pre-treatment).
A.8.2 Atomic Absorption Spectrometry
Measured according to GB 5009.12. When the graphite furnace atomic absorption spectrometry is used, the sample solution is treated as appropriate
dilution.
......
Tips & Frequently Asked Questions:
Question 1: How long will the true-PDF of GB 29217-2012_English be delivered?
Answer: Upon your order, we will start to translate GB 29217-2012_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.
Question 2: Can I share the purchased PDF of GB 29217-2012_English with my colleagues?
Answer: Yes. The purchased PDF of GB 29217-2012_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.
Question 3: Does the price include tax/VAT?
Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs):
List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?
Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.
