US$189.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email.
GB 29213-2012: Food additive potassium nitrate
Status: Valid
| Standard ID | USD | BUY PDF | Lead-Days | Standard Title (Description) | Status |
| GB 29213-2012 | 189 |
Add to Cart
|
3 days
|
Food additive potassium nitrate
| Valid |
Basic data
Standard ID: GB 29213-2012 (GB29213-2012)
Description (Translated English): Food additive potassium nitrate
Sector / Industry: National Standard
Classification of Chinese Standard: X40
Classification of International Standard: 67.220.20
Word Count Estimation: 8,819
Regulation (derived from): Ministry of Health Bulletin 2012 No. 23
Issuing agency(ies): Ministry of Health of the People's Republic of China
Summary: This Chinese standard applies to ammonium nitrate, sodium nitrate and potassium chloride as raw materials, the metathesis method or methods such as ion- exchange method produced, and then refining the food additive potassium nitrate.
GB 29213-2012: Food additive potassium nitrate
---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.
Food additive potassium nitrate
National Standards of People's Republic of China
National standards for food safety
Food Additives Potassium Nitrate
2012-12-25 release
2013-01-25 Implementation
Issued by the Ministry of Health of the People's Republic of China
National standards for food safety
Food Additives Potassium Nitrate
1 Scope
This standard applies to ammonium nitrate, sodium nitrate and potassium chloride as raw materials, by the decomposition method or ion exchange method and other methods, and then refined
Preparation of the food additive potassium nitrate.
2 Chemical name, molecular formula and relative molecular mass
2.1 Chemical name
Potassium nitrate
2.2 Molecular formula
KNO3
2.3 Relative molecular mass
101.1 (according to.2007 International relative atomic mass)
3 technical requirements
3.1 sensory requirements
Shall comply with the provisions of Table 1.
Table 1 sensory requirements
The project requires a test method
Colorless colorless or white
State granular crystals or crystalline powders
Take the appropriate amount of sample in a 50mL beaker and look under natural light
Color and state
3.2 Physical and chemical indicators
Shall comply with the provisions of Table 2.
Table 2 Physical and chemical indicators
Item Index Test Method
Potassium nitrate (KNO3) content (on dry basis), w /% 99.0 ~ 100.5 Appendix A in A.4
Dry reduction, w /% ≤ 1.0 Appendix A A.5
Table 2 (continued)
Item Index Test Method
Chlorate salt through Test Appendix A, A.6
Arsenic (As)/(mg/kg) ≤ 3 GB/T 5009.76
Lead (Pb)/(mg/kg) ≤ 4 GB 5009.12
Appendix A
Testing method
A.1 Warning
Some of the reagents used in the test methods of this standard are toxic or corrosive and should be operated with appropriate safety and protective measures.
A.2 General provisions
The reagents and water used in this standard, when not specified in other requirements, refer to the analysis of pure reagents and GB/T 6682-2008 in the provisions of the three
Water level. Standard standard solutions, preparations and articles for the determination of impurities in standard titration solutions and standards for the determination of these standards are not specified in the absence of other requirements
Prepared according to GB/T 601, GB/T 602, GB/T 603. The solution used refers to an aqueous solution when it is not specified with any solvent formulation.
A.3 Identification test
A.3.1 Reagents and materials
A.3.1.1 acetic acid.
A.3.1.2 Ethanol.
A.3.1.3 Sodium tartrate solution. 100 g/L.
A.3.1.4 Ammonia solution. 4 6.
A.3.1.5 potassium permanganate solution. c (1/5KMnO4) = 0.1mol/L. 3.161g potassium permanganate was weighed and dissolved in an appropriate amount of water
Release to 1000mL.
A.3.2 Identification method
A.3.2.1 Identification of potassium ions
Weigh 1g sample dissolved in 10mL water, adding sodium tartrate, the formation of white crystal precipitation, in the ammonia sample solution, the basic hydroxide
And the carbonate solution can be dissolved. Stirring, rubbing the inside of the tube with a glass rod or adding a small amount of acetic acid or ethanol can accelerate the precipitation
generate.
A.3.2.2 Identification of nitrate ions
A.3.2.2.1 Weigh 1 g of the sample in 10 mL of water and drop it into the potassium permanganate solution without causing a fading reaction.
A.3.2.2.2 Place the sample on the copper foil, add sulfuric acid, and heat the brown smoke.
A.4 Determination of potassium nitrate (KNO3) content
A.4.1 Reagents and materials
A.4.1.1 Sodium hydroxide solution. 400 g/L.
A.4.1.2 sulfuric acid solution. c (H2SO4) = 0.1 mol/L.
A.4.1.3 sodium hydroxide standard titration solution. c (NaOH) = 0.1mol/L.
A.4.1.4 Methyl red-methylene blue mixed indicator solution.
A.4.1.5 Water without ammonia.
A.4.1.6 Nitrogen fixation alloy. particle size not more than 0.85mm.
A.4.2 Instruments and equipment
A.4.2.1 Distillation apparatus. A nitrogen fixation apparatus according to Figure A.1 or other equipment with the same distillation capability.
A.4.2.2 zeolite.
1 --- distillation bottle;
2 --- splash tube;
3 --- dropping funnel;
4 --- ball-type grinding or rubber plug;
5 --- spherical condenser;
6 --- absorption bottle.
Figure A.1
A.4.3 Analysis steps
Weigh 0.4 g of the sample which had been dried at 105 ° C ± 2 ° C for 4 h, accurate to 0.0002 g. Add 300 mL of ammonia to the distillation flask
Water, shake the sample to dissolve. Add about 3g nitrogen and a few zeolites, the distillation bottle connected to the distillation device, the interface should be coated
Grease to prevent leakage. In the absorption bottle with a pipette into the 50mL sulfuric acid solution, add 4 drops to 5 drops of methyl red - methylene blue mixed instructions
Liquid and connected to the distillation unit. Add appropriate amount of water to the absorption bottle to ensure that the outlet of the draft tube is about 1.5 cm below the absorbed liquid level. by
Distillation unit of the separatory funnel by adding 15mL sodium hydroxide solution, the solution will flow into the 20mL ~ 30mL water rinse funnel, the remaining
3mL ~ 5mL water off the piston. After standing for 10min, turn on the cooling water, while heating, boiling according to the degree of foam adjustment
Heat strength, to avoid the bubble overflow or droplets out. After distilling at least 150 mL of distillate, check the droplets with a pH test paper, if not alkaline
The distillation is terminated. Flush the lower end of the diversion tube with a small amount of water and remove the absorption bottle. Titration of the suction bottle with titration solution with sodium hydroxide standard titration
The liquid is gray-green as the end point.
While the blank test. Blank test in addition to no sample, the other operations and the type and amount of reagents added (standard titration solution
And the same).
A.4.4 Calculation of results
The mass fraction w1 of the potassium nitrate (KNO3) content is calculated according to the formula (A.1)
w1 =
[(V0-V1)/1000] cM
m x 100%
(A.1)
Where.
V0 - the volume of sodium hydroxide standard titration solution consumed in the blank test in milliliters (mL);
V1 --- titration sample solution consumed by the volume of sodium hydroxide standard titration solution in milliliters (mL);
c - the exact value of sodium hydroxide standard titration solution concentration in moles per liter (mol/L);
M - the molar mass of potassium nitrate (KNO3) in grams per mole (g/mol) (M = 101.1);
m - the mass of the sample, in grams (g);
1000 --- conversion factor.
The experimental results are based on the arithmetic mean of the parallel measurement results, and the absolute difference between the two independent determinations obtained under the repeatability condition
The value is not greater than 0.3%.
A.5 Determination of dry reduction
A.5.1 Instruments and equipment
A.5.1.1 weighing bottle. φ30mm × 25mm.
A.5.1.2 electric thermostat oven. can control the temperature at 105 ℃ ± 2 ℃.
A.5.2 Analysis steps
Continue to dry at a temperature of 105 ° C ± 2 ° C until a constant weighing bottle weighing approximately 2 g of sample, accurate to 0.0002 g at 105 ° C ±
2 ℃ dry 4h, cooling 30min, weighing.
A.5.3 Calculation of results
The mass fraction w2 of the drying reduction is calculated according to the formula (A.2)
w2 =
m1-m2
m x 100%
(A.2)
Where.
m1 --- the mass of the sample and weighing bottle, in grams (g);
m2 --- the value of the sample after drying and the weight of the weighing bottle, in grams (g);
m - the mass of the sample, in grams (g).
The experimental results are based on the arithmetic mean of the parallel measurement results, and the absolute difference between the two independent determinations obtained under the repeatability condition
Value is not greater than 0.2%.
A.6 Determination of chlorate
Weigh about 0.1g The sample was dried at 105 ° C ± 2 ° C for 4 h. In a beaker, 2 mL of sulfuric acid was added and the sample remained white
There is odor and gas generated, that is through the test.
2102-
......
Tips & Frequently Asked Questions:
Question 1: How long will the true-PDF of GB 29213-2012_English be delivered?
Answer: Upon your order, we will start to translate GB 29213-2012_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.
Question 2: Can I share the purchased PDF of GB 29213-2012_English with my colleagues?
Answer: Yes. The purchased PDF of GB 29213-2012_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.
Question 3: Does the price include tax/VAT?
Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs):
List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?
Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.
