FZ/T 01094-2008 English PDFFZ/T 01094: Historical versions
Basic dataStandard ID: FZ/T 01094-2008 (FZ/T01094-2008)Description (Translated English): Textiles. Woven fabrics. Construction. Methods of analysis. Determination of the mass of warp and weft per unit area of fabric Sector / Industry: Spinning & Textile Industry Standard (Recommended) Classification of Chinese Standard: W04 Classification of International Standard: 59.080.30 Word Count Estimation: 5,592 Date of Issue: 2008-04-23 Date of Implementation: 2008-10-01 Older Standard (superseded by this standard): FZ/T 01094-1999 Quoted Standard: GB/T 4669; GB 6529 Adopted Standard: ISO 7211-6-1984, MOD Regulation (derived from): NDRC Notice No. 28 of 2008 Issuing agency(ies): National Development and Reform Commission of the People's Republic of China Summary: This standard specifies the measurement unit area of ??fabric quality of the warp and weft of the two methods, according to the needs can be one of them. This standard does not apply to the yarn of the fabric is not easy to disassemble. FZ/T 01094-2008: Textiles. Woven fabrics. Construction. Methods of analysis. Determination of the mass of warp and weft per unit area of fabric---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Textiles. Woven fabrics. Construction. Methods of analysis. Determination of the mass of warp and weft per unit area of fabric ICS 59.080.30 W04 People's Republic of China textile industry standards Replacing FZ/T 01094-1999 Woven fabric structure analysis method Determination of fabric weft yarn mass per unit area (ISO 7211-6. 1984, MOD) Posted 2008-04-23 2008-10-01 implementation National Development and Reform Commission, People's Republic of China released ForewordThis revised standard adopts ISO 7211-6. 1984 "textile fabric structure analysis machines - Part 6. Fabric basis by Determination of "weft yarn quality. This standard is based on ISO 7211-6. 1984 redrafted, and ISO 7211-6. 1984 The main differences are as follows. 1. Remove introduction; 2. Normative references are replaced by the corresponding international standards to national standards; 3. Increasing the range of the content is not applicable, and as part of the introduction of the article note; 4. Modify the description of the principle; 5. Test report adds "sample description." Instead of the standard FZ/T 01094-1999 "structural analysis of fabric woven fabrics weft yarn mass per unit area measurement." Compared with this standard FZ/T 01094-1999, in addition to editorial changes, mainly in the following technical modifications. 1. The original range was adjusted to 1.1 bar Note content; 2. Simplifying regulations and the humidity testing standards of air, the humidity will be prescribed specific time was changed to balance the humidity; 3. Simplify the description of the principles of the method A. The standard proposed by China Textile Industry Association. This standard by the National Standardization Technical Committee based textile branch (SAC/TC209/SC1) centralized. This standard was drafted. Textile Industry Standardization Institute, the Guangzhou Academy of fiber product testing. The main drafters of this standard. Zheng Yuying, He Yulan. This standard was first published in 1988, the standard number is GB/T 8682 - 1988, 1999 Adjustment for the textile industry standard, numbered FZ/T 01094-1999, this is the first revision. Woven fabric structure analysis method Determination of fabric weft yarn mass per unit area1 ScopeThis standard specifies two methods of fabric per unit area of the warp and weft of quality, according to needs can be one of them. This standard does not apply to yarn fabric is not easy to open. Note. usually the quality and the warp and weft density per unit area to describe the fabric, but can not determine the proportion of fabric in the warp and weft. Units are given fabric Quality area Jingwei yarn, yarn linear density without explanation, to clarify the latitude coverage comparison.2 Normative referencesThe following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard. Determination of GB/T 4669 Woven fabrics mass per unit length and mass per unit area GB 6529 textiles conditioning and testing - Standard atmospheres ISO 1833-1 Textiles - Quantitative chemical analysis - Part 1. General Test Principle 3 Method A. the sample draw a rectangle marked on the fabric samples tested, unless after the fibrous material to decompose remove warp and weft were measured Its quality. Method B. decomposition known area of sample yarn removed from the warp and weft unless after fibrous substances were determined its quality.4 Device4.1 does not fade the printing ink. 4.2 scissors. 4.3 Analysis of the needle. 4.4 Small template. square or rectangular area the size of the sample is consistent with the provisions of the length and width ratio should not exceed 4. 4.5 formwork. square, the size of the template to surround a small area is appropriate. 4.6 Balance. accurate to the smallest sample mass of 0.1%. 4.7 air oven.5 conditioning and testing atmosphereGB 6529 standard atmosphere specified pre humidity control, humidity control and testing.6 Sample6.1 The humidity Before marking or cutting samples, the samples were exposed for wet atmosphere to the standard balance. 6.2 Method A Big template with pencil and draw a mark on the sample square, diagonal fabric along the warp and weft directions. In the middle of the square with Small template and does not fade the ink mark to draw a square or rectangular area of not less than 150cm2 sample of their edges in parallel with the warp and weft. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of FZ/T 01094-2008_English be delivered?Answer: Upon your order, we will start to translate FZ/T 01094-2008_English as soon as possible, and keep you informed of the progress. The lead time is typically in 9 seconds (download/delivered in 9 seconds). The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of FZ/T 01094-2008_English with my colleagues?Answer: Yes. The purchased PDF of FZ/T 01094-2008_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version FZ/T 01094-2008?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version FZ/T 01094-2008 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |
