FZ/T 01091-2008 English PDFFZ/T 01091: Historical versions
Basic dataStandard ID: FZ/T 01091-2008 (FZ/T01091-2008)Description (Translated English): Textiles. Woven fabrics. Construction. Methods of analysis. Determination of crimp of yarn in fabric Sector / Industry: Spinning & Textile Industry Standard (Recommended) Classification of Chinese Standard: W04 Classification of International Standard: 59.080.30 Word Count Estimation: 6,681 Date of Issue: 2008-04-23 Date of Implementation: 2008-10-01 Older Standard (superseded by this standard): FZ/T 01091-1999 Quoted Standard: GB 6529 Adopted Standard: ISO 7211-3-1984, MOD Regulation (derived from): NDRC Notice No. 28 of 2008 Issuing agency(ies): National Development and Reform Commission of the People's Republic of China Summary: This standard specifies the determination of yarn in fabric shrinkage approach. This standard applies to most of the woven fabric, does not apply in certain straight yarn tension can not eliminate the curl, as well as weaving, finishing, and the method of analysis of the process of the destruction of the fabric yarns. FZ/T 01091-2008: Textiles. Woven fabrics. Construction. Methods of analysis. Determination of crimp of yarn in fabric---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order. Textiles. Woven fabrics. Construction. Methods of analysis. Determination of crimp of yarn in fabric ICS 59.080.30 W04 People's Republic of China textile industry standards Replacing FZ/T 01091-1999 Woven fabric structure analysis method Determination of yarn in fabric shrinkage (ISO 7211-3. 1984, MOD) Posted 2008-04-23 2008-10-01 implementation National Development and Reform Commission, People's Republic of China released ForewordThis revised standard adopts ISO 7211-3. 1984 "textile fabric structure analysis machines - Part 3. reduction of the woven fabric Determination. " This standard is based on ISO 7211-3. 1984 redrafted, and ISO 7211-3. 1984 The main differences are as follows. 1. As part of the introduction of the principles of Chapter 3 of the comment. 2. Normative references are replaced by the corresponding international standards to national standards. 3. The table in Appendix A straight tension incorporated within 8.1. 4. In Chapter 7, the sample increased on jacquard fabric sample comments. Instead of the standard FZ/T 01091-1999 "woven fabrics structure analysis method of yarn in fabric shrinkage determination." Compared with this standard FZ/T 01091-1999, the main changes the following technical content. 1. The original 3.1 to 3.5 5 to simplify terminology weave a term shrinkage. 2. 250mm length of the sample by the amended to "the specimen clamp 20 times the length." 3. Remove the fabric shrinkage formula (1). 4. The table in Appendix A straight tension incorporated within 8.1. The standard proposed by China Textile Industry Association. This standard by the National Standardization Technical Committee based textile branch (SAC/TC209/SC1) centralized. This standard was drafted. Textile Industry Standardization Institute, Xi'an University of Engineering. The main drafters. Zhang one, Zheng Yuying. This standard was first published in 1988, the standard number is GB/T 8679 - 1988, 1999 Adjustment for the textile industry standard, numbered FZ/T 01091-1999, this is the first revision. Woven fabric structure analysis method Determination of yarn in fabric shrinkage1 ScopeThis standard specifies the determination of yarn in fabric shrinkage method. This standard applies to most woven fabrics, does not apply in certain straight crimped yarn tension can not be eliminated, as well as weaving, whole Processing and analysis of the method of yarn fabric damaged.2 Normative referencesThe following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard. GB 6529 textiles conditioning and testing - Standard atmospheres3 Terms and DefinitionsThe following terms and definitions apply to this standard. 3.1 Stretched length of yarn in the fabric and the percentage difference between the distance of the yarn ends of the latter. 3.2 Eliminate curl weaving tension caused by the minimum force applied to the yarn. Principle 4 Remove from the fabric strip like a known length of yarn, under tension to make it straight and measure its length in this state, to weave shrink Rate shows the result. The size of the yarn tension according to the type and linear density selection. Note. This method required a tension crimped yarn straight. In theory, this tension should be to eliminate all without crimped yarn elongation, but actually difficult to achieve. Therefore, the tension given in Table 1, which are designed to stretch between the inevitable and does not completely eliminate curl balance, any residual curl It is negligible.5 device5.1 straight yarn and measuring devices, subject to the following requirements. a) shall have two clamps and clamp in a closed surface with parallel jaws; b) the distance between the two clamps can vary; c) should be able to measure the distance between the two clamps, the minimum scale is millimeters (mm); d) Each clamp shall have a baseline, you can see when the clamp is closed; Straight tension e) can specified by a clamp applied to the yarn. 5.2 ruler. minimum scale is millimeters (mm). 5.3 Analysis of the needle. ......Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of FZ/T 01091-2008_English be delivered?Answer: Upon your order, we will start to translate FZ/T 01091-2008_English as soon as possible, and keep you informed of the progress. The lead time is typically in 9 seconds (download/delivered in 9 seconds). The lengthier the document the longer the lead time.Question 2: Can I share the purchased PDF of FZ/T 01091-2008_English with my colleagues?Answer: Yes. The purchased PDF of FZ/T 01091-2008_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.Question 5: Should I purchase the latest version FZ/T 01091-2008?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version FZ/T 01091-2008 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. |