FZ/T 01007-2008 English PDF

US$199.00 · In stock
Delivery: <= 3 days. True-PDF full-copy in English will be manually translated and delivered via email.
FZ/T 01007-2008: Coated fabrics. Determination of resistance to low temperature
Status: Valid

FZ/T 01007: Historical versions

Standard ID	USD	BUY PDF	Lead-Days	Standard Title (Description)	Status
FZ/T 01007-2008	199	Add to Cart	3 days	Coated fabrics. Determination of resistance to low temperature	Valid
FZ/T 01007-1991	199	Add to Cart	2 days	Coated Fabrics - Test Method of Resistance to Low Temperature	Obsolete

Similar standards

FZ/T 01026   GB/T 251   GB/T 730   FZ/T 01010   FZ/T 01006   FZ/T 01004   

Basic data

Standard ID: FZ/T 01007-2008 (FZ/T01007-2008)
Description (Translated English): Coated fabrics. Determination of resistance to low temperature
Sector / Industry: Spinning & Textile Industry Standard (Recommended)
Classification of Chinese Standard: W04
Classification of International Standard: 59.080.40
Word Count Estimation: 8,867
Date of Issue: 2008-04-23
Date of Implementation: 2008-10-01
Older Standard (superseded by this standard): FZ/T 01007-1991
Quoted Standard: GB 6529
Adopted Standard: EN 1876-2-1998, MOD
Regulation (derived from): NDRC Notice No. 28 of 2008
Issuing agency(ies): National Development and Reform Commission of the People's Republic of China
Summary: This standard specifies the determination of the low temperature performance coated fabrics methods, including low-temperature impact test and extreme brittleness temperature measurement. This standard applies to the sample at room temperature, can be bent into a test state without injury coated fabric. This standard provides two different test parameters (parameters A and parameter B), test results can not be compared between, should be used as needed.

FZ/T 01007-2008: Coated fabrics. Determination of resistance to low temperature

---This is a DRAFT version for illustration, not a final translation. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.) will be manually/carefully translated upon your order.
Coated fabrics. Determination of resistance to low temperature ICS 59.080.40 W04 People's Republic of China textile industry standards Replacing FZ/T 01007-1991 Determination of low-temperature-resistant fabric coating Posted 2008-04-23 2008-10-01 implementation National Development and Reform Commission, People's Republic of China released

Foreword

This revised standard adopts EN1876-2.1998 "Rubber or plastic coated fabrics - Low-temperature test - Part 1. Circular ballistic method." According to this standard EN1876-2.1998 redrafted with EN1876-2.1998 The main differences are as follows. 1. Normative references in international standards replace national standards. 2. Increasing the relevant provisions of the B parameter. 3. The definition of the term "extreme embrittlement temperature" simplified. 4. Increase the low temperature impact test and related provisions. 5. Increase "if they can prove that the humidity had no significant effect on the results, you can not carry out the humidity" requirement. Instead of the standard FZ/T 01007-1991 "coated fabric low-temperature resistance test methods." This standard FZ/T 01007-1991, made the following major technical revisions. 1. Scope simplified. 2. EN1876-2 test parameters as a parameter A, the original method of test parameters as a parameter B. 3. Remove the cooling medium temperature impact tester. 4. Delete the term "crack" the term "cold crack temperature" to "extreme temperature embrittlement." 5. An increase of five transverse specimens. 6. Refine the destruction of the sample description and schematic samples given state. 7. The limit embrittlement temperature measured in terms of modifying the end of the test conditions. 8. Modify the calculation method of the final result. 9. Added Appendix A. Appendix A of this standard is an informative annex. The standard proposed by China Textile Industry Association. This standard by the National Standardization Technical Committee based textile branch (SAC/TC209/SC1) centralized. This standard was drafted. National Textile Products Quality Supervision and Inspection Center. The main drafters. Zhang Qiping, Renhe Ning. This standard was first published in 1991, this revision is the first time. Determination of low-temperature-resistant fabric coating

1 Scope

This standard specifies the method for determination of low temperature performance coated fabrics, including the determination of low temperature impact test and the limit embrittlement temperature. This standard applies to the sample at room temperature can be bent into a test status without damaging the coated fabric. This standard provides two different test parameters (parameters A and parameter B), does not have the comparability of results between the test should be based on the need to use.

2 Normative references

The following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard. GB 6529 textiles conditioning and testing - Standard atmospheres

3 Terms and Definitions

The following terms and definitions apply to this standard. 3.1 Coated fabric subject to certain impact at low temperatures, the coating surface of a temperature at failure. Principle 4 The sample is bent into a ring and placed in cold chamber at a certain initial temperature (in multiples of 5), by free-falling weight impact test kind. Then cooled to the temperature difference of 5 ℃, every change in temperature once the sample is a shock, until the sample appears damaged. Or at a predetermined relatively Low temperature impact hammer with a sample, the coating surface is observed to produce damage.

5 Sample

5.1 sample should be representative, clip from the effective width of each sample. 5.2 Each stall test temperature of at least 10 test samples, each of five vertical and horizontal. Each length dimension of the sample is 60mm, width (15 ± 0.5mm).

6 devices

6.1 cryogenic impact device has the following basic characteristics. --- Sample holding means can grip one or more samples; --- Hammer is a cylinder, a diameter in the range of 17mm ~ 30mm, bottom chamfer of 45 °; --- Hammer fixed at a certain height, can thus position of the free fall; --- Quality weight and height need to select one of the following parameters. Parameters A. weight mass of (200 ± 2) g, a height of (200 ± 2) mm. Parameters B. weight mass of (2500 ± 2.5) g, a height of (50 ± 0.5) mm. As an example, Appendix A gives two kinds of suitable impact device Fig. 6.2 cryogenic chamber to accommodate the impact of instrument should allow an interval of 5 ℃ temperature decreasing. Nearby cryogenic temperature deviation indoor specimens should be controlled At ± 1 ℃. ......

Image     

Tips & Frequently Asked Questions:

Question 1: How long will the true-PDF of FZ/T 01007-2008_English be delivered?

Answer: Upon your order, we will start to translate FZ/T 01007-2008_English as soon as possible, and keep you informed of the progress. The lead time is typically 1 ~ 3 working days. The lengthier the document the longer the lead time.

Question 2: Can I share the purchased PDF of FZ/T 01007-2008_English with my colleagues?

Answer: Yes. The purchased PDF of FZ/T 01007-2008_English will be deemed to be sold to your employer/organization who actually pays for it, including your colleagues and your employer's intranet.

Question 3: Does the price include tax/VAT?

Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countries

Question 4: Do you accept my currency other than USD?

Answer: Yes. If you need your currency to be printed on the invoice, please write an email to Sales@ChineseStandard.net. In 2 working-hours, we will create a special link for you to pay in any currencies. Otherwise, follow the normal steps: Add to Cart -- Checkout -- Select your currency to pay.

Question 5: Should I purchase the latest version FZ/T 01007-2008?

Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version FZ/T 01007-2008 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically.