CB1146.9-1996 PDF EnglishUS$140.00 · In stock · Download in 9 seconds
CB1146.9-1996: Ship equipment environmental test and engineering guidance - Vibration (sinusoidal) Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedure
CB1146.9-1996: Ship equipment environmental test and engineering guidance - Vibration (sinusoidal)---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/CB1146.9-1996 CB MINISTERIAL STANDARD OF CHINA SHIPBUILDING CORPORATION U08 Replacing CB 1146.9-85 Ship equipment environmental test and engineering guidance - Vibration (Sinusoidal) Issued on: DECEMBER 23, 1996 Implemented on: JUNE 1, 1997 Issued by. China Shipbuilding Corporation Table of Contents1 Subject content and application scope ... 3 2 References ... 3 3 Terms ... 3 4 Test conditions ... 4 5 Severity level ... 6 6 Test procedures ... 8 7 Test interruption handling ... 10 8 Qualification criteria ... 10 9 Test records and files ... 11 10 Engineering guidance ... 11 11 Details need to be specified when referencing this Standard ... 11 Annex A ... 12 Annex B ... 19 Ship equipment environmental test and engineering guidance - Vibration (Sinusoidal)1 Subject content and application scopeThis Standard specifies the test conditions, severity, test procedures and acceptance criteria of environmental vibration (sinusoidal) test of ship equipment; and it provides the engineering guidance. This Standard applies to the environmental test for evaluation of work adaptability and structural integrity of ship equipment under specified vibration conditions.2 ReferencesGB/T 2423.10-1995 Environmental testing for electric and electronic products - Part 2. Test methods - Test Fc and guidance. Vibration (Sinusoidal) CB 1146.1-96 Ship equipment environmental test and engineering guidance - General rules3 Terms3.1 Fixed point Point where test samples contact with fixtures or vibrating table, it is usually the places where fix the test samples when using. If a part of the actual installation structure is used for the fixture, it shall choose the contacting point of this part with vibration table as the fixed point, rather than the contracting point of the sample with installation structure. 3.2 Measuring point Some specific points for data collection during test, the data collected are used for inspecting test parameters or controlling test parameters. Note. Measuring points that are set to evaluate the performance of samples or to detect the vibration response characteristics of each part are not used as measuring points in this Standard. 3.2.1 Detection point Points that are located in the fixtures, vibration table or samples, and are kept as closer as possible to the fixed points. If there are 4 or less than 4 fixed points, each of which can be taken as a detection point; if there are more than 4 fixed points, then the relevant standards shall specify 4 representative fixed points as the detection points. Under special circumstances, such as large or complex samples, if the detection points are required to be at other places (not close to fixed points), then it shall be specified by relevant standards, or determined by test engineering. When several small samples are mounted onto a fixture, or when a small sample having a number of fixed points, in order to derive the control signal, it can choose a single detection point, which shall be selected from the fixed points of samples and fixtures, not the fixed points of fixtures and vibration table. This is feasible only when the lowest resonant frequency exceeds the upper-limit of the test frequency after the sample is mounted onto the fixture. 3.2.2 Reference point Points that are selected from the detection points, the signal at these points is used to control the test. 3.3 Control point 3.3.1 Single point control Single point control is achieved by using the signal from the sensor at the reference points, so as to make the vibration parameters of this point remain within a specified range. 3.3.2 Multipoint control Multipoint control is achieved by using the sensor signal at each selected detection point, and process the signal by continuous arithmetic average or comparison technique, so as to generate a control signal.4 Test conditions4.1 Characteristics requirements for vibration table The vibration table shall have the following characteristics when it is mounted with fixtures and samples. 4.1.1 Basic movement The basic movement shall be sinusoidal function of time; the fixed points of samples shall be basically the same, moving along parallel lines, and in accordance with the tolerance requirements of 4.1.2 and 4.1.3. 4.1.2 Lateral movement Mast-area refers to the mast part; the main body refers to other parts except the mast part. If the known equipment is installed only on a particular ship, the upper frequency limit of test is the highest blade-frequency (the maximum rotating speed of propeller × number of blades ÷ 60) of this ship; if there are special requirements, it is specified by the relevant standards, specifications or order contract.6 Test procedures6.1 Initial inspection Before the test, according to the specifications of product test outline or technical conditions, the sample shall be performed with appearance inspection, electrical and mechanical properties test; if it fails to meet the requirements, this test must not be performed. 6.2 Test conditions Samples shall be performed with vibration response inspection and vibration durability test. For those performed with sweep-frequency durability test only, the above-mentioned two tests can be combined into one. Unless otherwise specified in product standards or technical documents, these two tests shall be performed on three mutually perpendicular axels. The test sequence is that, two tests can be performed in one axial and then in another axial; or one test is performed in three axels and then perform another test in three axels. 6.2.1 Vibration response inspection According to the amplitude specified in Table 1, within the test frequency range, from low frequency to high frequency, and then from high frequency to low frequency; sweep back and forth at a rate of one octave per minute, for 1 to 2 times. Unless otherwise specified in product standards or technical documents, during the vibration response inspection, the sample shall be at normal working condition; If the mechanical vibration characteristics can not be determined because the sample is at working condition, then this sample shall be performed with additional response inspection at non-working condition. During vibration response inspection, it shall test the vibration response of main structure and internal partial structure of the sample; and visually inspect the current, voltage and other performance changes indicated on indicating instrument or observed by other performance teat method, so as to judge the critical frequency of the following phenomenon. a. there are faults and (or) performance degradation of samples; b. mechanical resonance or other response phenomenon. 6.3 Intermediate inspection During the condition test, it shall test the main performance of samples. 6.4 Recovery When it is required by the relevant specifications, at the end of condition test, it shall provide a period of recovery time, so as to make the sample recover to the same test conditions as that of initial detection. 6.5 Final inspection After recovery, according to the specifications of product test program or technical documents, perform appearance inspection, electrical performance and mechanical performance to the samples.7 Test interruption handlingDuring test, if there are great faults, such as structural damage or malfunction, that are out of the permitted range of product test program or technical conditions, the test shall be interrupted. After being repaired, repeat the vibration test; the sample provider can provide new samples for retest. If there are non-repeating faults that can be easily replaced or repaired, such as indicating- light and component damage AND welding defects, the test shall be also interrupted. After being repaired, repeat only the test items that have faults; repeating the whole vibration test is not required. No matter what kind of test interruption above occurs, it shall be described in detail in the test report.8 Qualification criteriaTest samples without the following faults during test and after test can be deemed as qualified. a. mechanical damage or injury that influence the completion of main functions; b. during final inspection, there is a performance indicator that fails to meet the requirements; c. during final inspection, all performance indicators meet the requirements, but during vibration response inspection and sweep-frequency dura... ......Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al. Tips & Frequently Asked Questions:Question 1: How long will the true-PDF of English version of CB1146.9-1996 be delivered?Answer: The full copy PDF of English version of CB1146.9-1996 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice.Question 2: Can I share the purchased PDF of CB1146.9-1996_English with my colleagues?Answer: Yes. The purchased PDF of CB1146.9-1996_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet.Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- CB1146.9-1996 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds.How to buy and download a true PDF of English version of CB1146.9-1996?A step-by-step guide to download PDF of CB1146.9-1996_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).Step 2: Search keyword "CB1146.9-1996". Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart. Step 4: Select payment option (Via payment agents Stripe or PayPal). Step 5: Customize Tax Invoice -- Fill up your email etc. Step 6: Click "Checkout". Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively. Step 8: Optional -- Go to download PDF. Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice. See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9 |
