NY 39-1987 PDF in English
NY 39-1987 (NY39-1987) PDF English
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Name of Chinese Standard | Status |
| NY 39-1987 | English | 95 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Feed grade L-lysine monohydrochloride
| |
Standards related to: NY 39-1987
PDF Preview
NY 39-1987: PDF in English NY 39-1987
NY
NATIONAL STANDARD OF
THE PEOPLE’S REPUBLIC OF CHINA
UDC 636.085.57
(Renamed from GB 8245-87)
Feed grade L-lysine monohydrochloride
饲料级 L-赖氨酸盐酸盐
ISSUED ON. SEPTEMBER 14, 1987
IMPLEMENTED ON. OCTOBER 1, 1988
Issued by. Ministry of Agriculture, Forestry and Fisheries of China
Table of Contents
Foreword ... 3
1 Technical requirements ... 4
2 Test method ... 4
3 Acceptance rules ... 11
4 Packaging, marks, storage and transport ... 11
Additional information... 12
Corrigendum -- GB 8245-87 Feed grade L-lysine monohydrochloride ... 13
Foreword
This Standard was proposed by Ministry of Agriculture, Forestry and Fisheries
of China.
Main drafting organizations of this Standard. China Veterinary Drug
Administration, Guangxi Lysine Plant.
Main drafters of this Standard. Zhong Feng, Huang Huiqiang, Li Meitong.
This Standard is equivalent with Japan Feed Safety Law.
analytical reagents and distilled water, or water of corresponding purity.
In the absence of other requirements, the standard solution used shall be in
accordance with GB 601-77 Standard solution preparation method; the impurity
standard solution shall be in accordance with GB 602-77 Impurity standard
solution preparation method; Preparation and products shall be prepared
according to GB 603-77 Preparation method for preparation and products.
2.1 Identification
2.1.1 Reagents and solutions
2.1.1.1 Ninhydrin (HG 3-984-76). 0.1% (m/V) solution;
2.1.1.2 Silver nitrate (GB 670-77). 0.1 mol/l solution;
2.1.1.3 Nitric acid (GB 626-78). 1+9 solution;
2.1.1.4 Ammonium hydroxide (GB 631-77). 1+2 solution.
2.1.2 Identification method
2.1.2.1 Identification of amino acid
Weigh 0.1 g of specimen. Dissolve it in 100 ml of water. Take 5 ml of this solution.
Add 1 ml of ninhydrin solution (2.1.1.1). After heating for 3 min, add 20 ml of
water. Place it still for 15 min. The solution shall look reddish purple.
2.1.2.2 Identification of chloride
Weigh 1 g of specimen. Dissolve it in 10 ml of water. Add silver nitrate solution
(2.1.1.2), white precipitate shall be generated. Take this precipitate and add
dilute nitric acid (2.1.1.3). The precipitate shall not be solved. Take this
precipitate added with excessive ammonium hydroxide solution, it shall dissolve.
2.2 Determination of lysine hydrochloride content
2.2.1 Reagents and solutions
2.2.1.1 Formic acid (HG 3-1296-80);
2.2.1.2 Glacial acetic acid (GB 676-78)
2.2.1.3 Mercuric acetate (HG 3-1096-77). 6% (m/V) glacial acetic acid
solution;
2.2.1.4 α- Naphthol phenylmethanol indicator. 0.2% (m/V) glacial acetic acid
solution;
where,
m - specimen mass before drying, g;
m1 - specimen mass after drying, g.
2.5 Determination of burning residue
2.5.1 Instruments and equipment
2.5.1.1 High temperature furnace. the controllable temperature is 550±20°C;
2.5.1.2 Porcelain crucible. 30 ml;
2.5.1.3 Dryer. using calcium chloride or silica gel as desiccant.
2.5.2 Determination method
In the porcelain crucible which has been burnt to constant weight, weigh 1 g of
specimen, to the neatest of 0.0002 g. Carbonize it in the electric furnace
carefully till there is no black smoke. Then transfer it to the high temperature
furnace for 3 ~ 4 hour burning at 550°C. Take it out. Cool it for a while then put
it into the dryer. Cool it to room temperature. Weigh it. Repeat burning for 1h
and weigh till constant weight.
2.5.3 Calculation of results
The percentage of burning residue of L-lysine monohydrochloride shall be
calculated according to equation (4).
where,
m - specimen mass, g;
m1 - mass of empty constant weight crucible, g;
m2 - mass of ash and crucible, g.
2.6 Determination of ammonium salt
2.6.1 Reagents and solutions
2.6.1.1 Magnesium oxide (HG 3-1294-80);
according to the provisions of GB 602-77 then accurately dilute it to 10 times.
2.7.2 Determination method
Weigh 1 g of specimen, to the nearest of 0.01 g. Place it in the porcelain crucible.
Carefully carbonize it on the electric furnace. Burn it at 550°C for 3h (or use the
residual ash after residue determination of sub-clause 2.5). Add 4 ml of
hydrochloric acid (2.7.1.1) into the residue. Heat it on the water bath and
evaporate to dry. Add 10 ml of hot water and dip for 2min. Transfer all into the
Nessler color tube. Add 2 ml of acetic acid solution (2.7.1.2). Use water to dilute
it to 50 ml. Add 2 drops of sodium sulfide solution (2.7.1.3). Place it for 5min.
Pipette 3 ml of lead standard solution (2.7.1.4). Take the same color as the
sample as a standard. The color of the sample solution must not be deeper than
this standard solution.
2.8 Determination of arsenic
2.8.1 Reagents and solutions
2.8.1.1 Hydrochloric acid (GB 622-77). 1+1 solution;
2.8.1.2 Potassium iodide (GB 1272-77). 16.5% (m/V) solution;
2.8.1.3 Stannous chloride (GB 638-78). 40% (m/V) hydrochloric acid solution,
effective within one month;
2.8.1.4 Arsenic-free metal zinc (GB 2304-80);
2.8.1.5 Lead acetate skimmed cotton;
2.8.1.6 Mercury bromide test paper;
2.8.1.7 Arsenic standard solution. 0.01 mg of As contained in 1 ml. Prepare it
according to the provisions of GB 602-77 then accurately dilute it to 10 times
when required.
2.8.2 Determination method
Pipette 1 g of specimen, to the nearest of 0.01 g. Place it in a wild-mouth jar.
Determine it according to the provisions of “1 Arsenic spot method” in GB 610-
77 Arsenic determination. Its color must not be deeper than the standard one.
Pipette 2 ml of arsenic standard solution (2.8.1.7). Process it same with
specimen simultaneously as standard.
exceed 25 kg.
4.2 The packaging shall have a solid mark, indicating product name,
manufacture’s name and address, lot number, approval file number, storage
conditions, use method, net weight, exit-factory date, and words of "feed grade".
4.3 The exit-factory products shall be accompanied by a quality certificate,
including product name, manufacturer’s name and address, lot number,
approval file number, product quality, reference of this Standard and laboratory
technician’s code.
4.4 This product shall be stored in a cool, dry, ventilated place.
4.5 During transport, it shall prevent rain and sun. It must not be stored or
transported with toxic and hazardous substances.
Additional information.
This standard was proposed by Ministry of Agriculture, Forestry and Fisheries
of the People's Republic of China.
This standard was responsibly drafted by China Veterinary Drug Monitoring
Institute AND Guangxi Lysine Plant.
The main drafters of this standard are Zhong Feng, Huang Huiqiang and Li
Meidong.
This standard equivalently adopts Japan's feed safety law.
......
Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.
|