GB/T 5125-2008 PDF English
US$155.00 · In stock · Download in 9 secondsGB/T 5125-2008: Method for deep drawing cups testing of non-ferrous metals Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid GB/T 5125: Evolution and historical versions
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 5125-2008 | English | 155 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Method for deep drawing cups testing of non-ferrous metals
| Valid |
| GB/T 5125-1985 | English | 239 |
Add to Cart
|
2 days
|
Method for deep drawing cups testing of non-ferrous metals
| Obsolete |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 5125-2008
GB/T 5125-2008: Method for deep drawing cups testing of non-ferrous metals---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT5125-2008
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 77.040.10
H 22
Replacing GB/T 5125-1985
Method for deep drawing cups testing of non-ferrous metals
ISSUED ON: JUNE 17, 2008
IMPLEMENTED ON: DECEMBER 01, 2008
Issued by: General Administration of Quality Supervision, Inspection and
Quarantine of PRC;
National Standardization Administration.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Terms and definitions ... 4
4 Symbols and instructions ... 6
5 Principle of the method ... 7
6 Specimens ... 7
7 Test equipment and tools ... 7
8 Test steps ... 8
9 Test results ... 9
10 Test report ... 10
Method for deep drawing cups testing of non-ferrous metals
1 Scope
This standard specifies the deep drawing cups testing method for nonferrous metals.
This standard applies to the deep drawing cups testing method for nonferrous metal
sheets and strips, which have a thickness of 0.10 mm ~ 3.00 mm for deep drawing at a
temperature of 10 °C ~ 35 °C.
2 Normative references
The provisions in following documents become the provisions of this Standard through
reference in this Standard. For the dated references, the subsequent amendments
(excluding corrections) or revisions do not apply to this Standard; however, parties who
reach an agreement based on this Standard are encouraged to study if the latest versions
of these documents are applicable. For undated references, the latest edition of the
referenced document applies.
GB/T 8170 Rules of rounding off for numerical values and expression and
judgement of limiting values
GB/T 16825 (all parts) Verification of static uniaxial testing machines
JJG 583 Verification regulation of cupping testing machine
3 Terms and definitions
The following terms and definitions apply to this standard.
3.1
Disc specimen
Disc specimen is a round blank or machined round test piece, which is punched from
a thin plate or strip.
3.2
Pressure on edge
The vertical pressure, which is applied by the clamping device on the disc specimen,
a) The universal testing machine shall be calibrated in accordance with GB/T 16825;
it shall have a clamping device for applying and adjusting the blank holding force;
b) The cup drawing test machine shall be calibrated in accordance with JJG 583.
7.2 Test tools
The test tools are as shown in Figure 1. The following basic requirements shall be met:
a) The working surface of the punch and die shall be polished; the surface roughness
parameter (Ra) shall not exceed 3.2 μm;
b) The punch and die shall be made of high-quality alloy steel which has a hardness
of HRC58 ~ 60;
c) The radius transition of the punch and die shall be gentle and smooth;
d) The main dimensions of the punch and die are as shown in Table 2.
8 Test steps
8.1 According to the thickness of the disc specimen, select the appropriate punch and
die according to Table 2. The punch diameter deviation is , the die diameter
deviation is , the punch or die's fillet radius deviation is ±0.05 mm.
8.2 Install the punch and die; eccentricity is not allowed.
8.3 Apply a small amount of lubricant, such as engine oil, industrial vaseline, etc., to
the upper and lower surfaces of the disc specimen.
8.4 Place the disc specimen in the die.
8.5 Adjust the clamping device and apply appropriate pressure to the disc specimen, so
that there will be no unstable wrinkles when the disc is stretched, meanwhile it is easy
to stamp and form without breaking.
8.6 Move the punch or die at a controllable uniform speed, until the cup is punched out
and the cup is not broken.
8.7 Measure the earing peak and earing valley of the cup. The measurement accuracy
shall be not less than 0.05 mm.
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 5125-2008 be delivered?Answer: The full copy PDF of English version of GB/T 5125-2008 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 5125-2008_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 5125-2008_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 5125-2008 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. Question 5: Should I purchase the latest version GB/T 5125-2008?Answer: Yes. Unless special scenarios such as technical constraints or academic study, you should always prioritize to purchase the latest version GB/T 5125-2008 even if the enforcement date is in future. Complying with the latest version means that, by default, it also complies with all the earlier versions, technically. How to buy and download a true PDF of English version of GB/T 5125-2008?A step-by-step guide to download PDF of GB/T 5125-2008_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 5125-2008".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|