GB/T 42764-2023 PDF English
US$170.00 · In stock · Download in 9 secondsGB/T 42764-2023: Plastics - Assessment of the intrinsic biodegradability of materials exposed to marine inocula under mesophilic aerobic laboratory conditions - Test methods and requirements Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 42764-2023 | English | 170 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Plastics - Assessment of the intrinsic biodegradability of materials exposed to marine inocula under mesophilic aerobic laboratory conditions - Test methods and requirements
| Valid |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 42764-2023
GB/T 42764-2023: Plastics - Assessment of the intrinsic biodegradability of materials exposed to marine inocula under mesophilic aerobic laboratory conditions - Test methods and requirements
---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT42764-2023
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 83.080.01
CCS G 31
GB/T 42764-2023 / ISO 22403:2020
Plastic - Assessment of the intrinsic biodegradability of
materials exposed to marine inocula under mesophilic
aerobic laboratory conditions - Test methods and
requirements
(ISO 22403:2020, IDT)
ISSUED ON: MAY 23, 2023
IMPLEMENTED ON: DECEMBER 01, 2023
Issued by: State Administration for Market Regulation;
Standardization Administration of the People’s Republic of China.
Table of Contents
Foreword ... 3
Introduction ... 4
1 Scope ... 5
2 Normative references ... 6
3 Terms and definitions ... 7
4 Requirements ... 7
5 Test report ... 9
Bibliography ... 10
Plastic - Assessment of the intrinsic biodegradability of
materials exposed to marine inocula under mesophilic
aerobic laboratory conditions - Test methods and
requirements
1 Scope
This document describes test methods for assessing the inherent biodegradability of
plastic raw materials and polymers in marine environments without any environmental
exposure or pretreatment.
The test methods in this document are carried out under aerobic, mesophilic conditions
and are aimed to obtain the ultimate biodegradability of materials, i.e. conversion into
carbon dioxide, water, and biomass.
This document is only used to evaluate the inherent biodegradability of materials. It is
not used to evaluate the environmental hazards of possible constituents such as heavy
metals and other substances, nor is it used to evaluate its potential ecotoxicity. This
document is suitable for assessing the overall environmental impact of plastics released
intentionally or unintentionally into the marine environment.
This document is not used to evaluate the performance of products processed from
biodegradable plastic raw materials and biodegradable polymers. The lifetime and
biodegradation rate of biodegradable plastic products in the ocean are often affected by
specific environmental conditions as well as the thickness and shape of the product.
The test results of biodegradability obtained under the test conditions specified in this
document cannot be directly extrapolated to the actual marine environment.
This document does not apply to “marine biodegradable” claims for biodegradable
plastic raw materials. If necessary, refer to the relevant product standard.
The test methods specified in this document cannot be used to determine the specific
biodegradation rate (i.e. rate per available surface area) of the test material. If necessary,
refer to the relevant standards about biodegradation rates.
4.3 Negative control material
The negative control material shall be tested in parallel with the test material. The
negative control material is virgin polyethylene.
4.4 Biodegradation test methods
Plastic raw materials, polymers or each organic constituent shall be subjected to marine
biodegradation tests together with reference materials and negative control materials,
respectively. The tests shall be carried out in accordance with any of the following 6
documents: ISO 18830, ISO 19679, ISO 22404, ASTM D6691-17, ISO 23977-1, and
ISO 23977-2.
The test ends when the test reaches a plateau phase. When the average biodegradation
rate of at least 3 test materials is less than 3 % within 2 months, the test can be
considered to have reached a plateau phase. After 1 year of testing, the test conditions
shall be carefully monitored following the corresponding standard test methods to
ensure long-term reliability of the test conditions. The results are only valid if the test
method meets the corresponding standards.
4.5 Requirements
For whole test material or each individual constituent, organic carbon shall mineralize
into carbon dioxide within 2 years for a degree of mineralization of at least 90 %, or for
the extent of the reference material. In this document, this requirement is met if the
mineralization relative to the reference material is ≥90 %. Both the reference material
and the test material shall be tested within the same period, and the results shall be
compared at the same point after both tests have reached a plateau phase.
For organic constituents with a content between 1 % ~ 15 % (dry mass) in the material,
the biodegradability shall be determined separately. It may refer to OECD 301 Methods
A ~ F to determine based on the existing biodegradation test results. This document
recognizes the biodegradability under conditions described in OECD 310.
Alternatively, it may also use an artificial blend of the same material to determine the
biodegradability of an organic constituent. The artificial blend shall contain ≥15 % of
the corresponding organic constituent [by total organic carbon (TOC) content]. The
chemical composition and the structure of the material shall remain the same, but the
content of the organic constituent of concern shall be increased to ≥15 % [by total
organic carbon (TOC) content]. The preparation of the artificial blend shall use the same
process conditions (e.g. extrusion) as used for the raw materials, except that the content
of each constituent in the raw materials may be less than 15 % (by dry mass). If the
artificial blend meets the above requirements, the organic constituent is considered
biodegradable. Therefore, when the content of this constituent in a certain material is
≤15 % (based on dry mass), the above results are also applicable.
NOTE 1: The purpose of testing an artificial blend is to verify a synergistic effect demonstrating
that a constituent, which is suspected of being non-biodegradable when tested alone, may
become biodegradable when combined with another biodegradable constituent of a material.
NOTE 2: The purpose of increasing the content of a certain constituent in the artificial blend to
≥15 % is to avoid false-positive test results, because theoretically a material contains 10 % of a
non-biodegradable constituent may still reach the pass level for biodegradation.
Natural materials and constituents that have not been chemically modified (such as
wood, wood fiber, cotton fiber, starch, paper pulp, bagasse, jute) shall be considered to
be biodegradable in nature without testing.
In principle, the biodegradation test results obtained using any of the test methods in
4.4 can prove whether the material is susceptible to biodegradation by marine
microorganisms. However, some test materials that fail the test may be the consequence
of being affected by the quality or quantity (or both) of the ineffective microbial
population in an inoculum. Thus, when the test is repeated using different inoculum,
the material may show signs of biodegradability.
The above laboratory test methods shall be carried out between 15 °C and 25 °C, but
not exceeding 28 °C.
NOTE 3: When the test temperature is higher than 20 °C ~ 22 °C, the biodegradability of
psychrophilic microbes may be inhibited.
5 Test report
The test report shall contain at least the following content:
- all identification information of the plastic material or polymer being tested;
- the test methods used in the test, the results, and whether the specified requirements
have been satisfied;
- annexes with the specific test reports of the test method used.
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 42764-2023 be delivered?Answer: The full copy PDF of English version of GB/T 42764-2023 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 42764-2023_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 42764-2023_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 42764-2023 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. How to buy and download a true PDF of English version of GB/T 42764-2023?A step-by-step guide to download PDF of GB/T 42764-2023_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 42764-2023".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|