GB/T 36943-2018 PDF English
Search result: GB/T 36943-2018 English: PDF (GB/T36943-2018)
Standard ID | Contents [version] | USD | STEP2 | [PDF] delivered in | Name of Chinese Standard | Status |
GB/T 36943-2018 | English | 130 |
Add to Cart
|
0-9 seconds. Auto-delivery.
|
Designation and marking requirements of lithium-ion batteries for electric bicycle
| Valid |
BUY with any currencies (Euro, JPY, GBP, KRW etc.): GB/T 36943-2018 Related standards: GB/T 36943-2018
PDF Preview: GB/T 36943-2018
GB/T 36943-2018: PDF in English (GBT 36943-2018) GB/T 36943-2018
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 43.140
Y 14
Designation and Marking Requirements
of Lithium-Ion Batteries for Electric Bicycle
ISSUED ON: DECEMBER 28, 2018
IMPLEMENTED ON: JULY 01, 2019
Issued by: State Administration for Market Regulation;
Standardization Administration of PRC.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative References ... 4
3 Terms and Definitions ... 4
4 Single Battery Model Naming and Compilation Method ... 5
5 Battery Pack Model Naming and Preparation Method ... 7
6 Marking ... 9
Designation and Marking Requirements
of Lithium-Ion Batteries for Electric Bicycle
1 Scope
This Standard specifies the designation and marking requirements of lithium-ion
batteries for electric bicycle.
This Standard is applicable to the lithium-ion batteries for electric bicycle.
2 Normative References
The following documents are essential to the application of this document. For the
dated documents, only the versions with the dates indicated are applicable to this
document; for the undated documents, only the latest version (including all the
amendments) are applicable to this document.
GB/T 36945-2018 Vocabulary of Lithium-Ion Batteries for Electric Bicycle
QB/T 4428-2012 Specification and Dimension of Lithium-Ion Batteries for Electric
Bicycle
3 Terms and Definitions
For the purposes of this document, the terms and definitions given in GB/T 36945-
2018 and the following apply.
3.1 Middle-installed battery
A battery that uses a battery case and is placed in the middle of the electric bicycle.
3.2 Back-installed battery
A battery that uses a battery case and is placed in the rear of the electric bicycle.
3.3 Built-in battery
A battery directly placed inside the body structure of the electric bicycle.
Example 3:
The model of square lithium-ion battery with thickness about 7mm, width about 34mm, height
about 48mm, with embedded characteristic negative system and lithium iron phosphate anode
shall be prepared as ITP7/34/48.
Example 4:
The model of square polymer lithium-ion battery with thickness about 2.4mm, width about
68mm, height about 70mm, with embedded characteristic negative system and manganese
base anode shall be prepared as IMPt24/68/70.
5 Battery Pack Model Naming and Preparation Method
5.1 Model composition
5.1.1 General
The model of battery pack consists of the battery pack’s usage code, nominal voltage
code, rated capacity code, installation method (position) code, size additional number
code, and positive system code.
5.1.2 Usage code
The usage code of the battery pack uses two capital letters in English of DZ for electric
bicycle.
5.1.3 Nominal voltage code and rated capacity code
The nominal voltage code and rated capacity code of the battery pack separately
consist of two Arabic numerals; when the integer is less than 10, then supplement “0”
in the tens place. For example, if the nominal voltage of the battery pack is 24V, then
its code is 24. If the rated capacity of the battery pack is 9Ah, then its code is 09, and
so on.
5.1.4 Installation method (position) code
If battery pack is installed at different positions of the electric bicycle, the installation
size and method are different. The installation method code of the battery pack is
indicated by a capital letter in English, as shown in Table 2.
5.2.2 Model preparation example
The model of the battery pack shall be prepared as per the requirements of 5.2.1.
Example 1:
The model of lithium-ion battery adopting the external middle-installed mode, with nominal
voltage 36V, rated capacity of 10Ah, adopting lithium iron phosphate as anode material, with
the appearance size of the battery 375mm×135mm×90mm shall be prepared as DZ36Z-10AT.
Example 2:
The model of lithium-ion battery adopting the external back-installed mode, with nominal
voltage 48V, rated capacity 12Ah, adopting ternary material as anode material, with the
appearance size of battery 390mm×170mm×80mm shall be prepared as DZ48H-12BS.
6 Marking
6.1 General
The outer surface of each single battery and battery pack shall have a clear, long-
lasting and non-shedding marking.
6.2 Marking of single battery
The single battery marking shall have the following information:
a) Product name;
b) Specification and model;
c) Nominal voltage;
d) Rated capacity;
e) Polarity;
f) Manufacture date or batch number;
g) Name of manufacturer or producer.
6.3 Marking of battery pack
The battery pack marking shall have the following Chinese information:
a) Product name;
...... Source: Above contents are excerpted from the PDF -- translated/reviewed by: www.chinesestandard.net / Wayne Zheng et al.
|