GB/T 26949.12-2021 PDF English
US$230.00 · In stock · Download in 9 secondsGB/T 26949.12-2021: Industrial trucks - Verification of stability - Part 12: Industrial variable-reach trucks handling freight containers of 6 m length and longer Delivery: 9 seconds. True-PDF full-copy in English & invoice will be downloaded + auto-delivered via email. See step-by-step procedureStatus: Valid
| Standard ID | Contents [version] | USD | STEP2 | [PDF] delivery | Name of Chinese Standard | Status |
| GB/T 26949.12-2021 | English | 230 |
Add to Cart
|
0-9 seconds. Auto-delivery
|
Industrial trucks - Verification of stability - Part 12: Industrial variable-reach trucks handling freight containers of 6 m length and longer
| Valid |
Excerpted PDFs (Download full copy in 9 seconds upon purchase)PDF Preview: GB/T 26949.12-2021
GB/T 26949.12-2021: Industrial trucks - Verification of stability - Part 12: Industrial variable-reach trucks handling freight containers of 6 m length and longer
---This is an excerpt. Full copy of true-PDF in English version (including equations, symbols, images, flow-chart, tables, and figures etc.), auto-downloaded/delivered in 9 seconds, can be purchased online: https://www.ChineseStandard.net/PDF.aspx/GBT26949.12-2021
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 53.030
CCS J 83
GB/T 26949.12-2021 / ISO 22915-12:2015
Industrial trucks - Verification of stability - Part 12:
Industrial variable-reach trucks handling freight containers
of 6 m length and longer
(ISO 22915-12:2015, IDT)
ISSUED ON: DECEMBER 31, 2021
IMPLEMENTED ON: JULY 01, 2022
Issued by: State Administration for Market Regulation;
Standardization Administration of PRC.
Table of Contents
Foreword ... 3
Introduction ... 5
1 Scope ... 7
2 Normative references ... 7
3 Terms and definitions ... 8
4 Operating conditions ... 9
5 Test conditions ... 9
6 Verification of stability ... 14
7 Markings ... 14
References ... 18
Industrial trucks - Verification of stability - Part 12:
Industrial variable-reach trucks handling freight containers
of 6 m length and longer
1 Scope
This document specifies test methods for verifying the stability of industrial variable-
reach trucks handling empty or fully loaded freight containers of 6 m length and longer.
This document applies to industrial variable-reach trucks, which are equipped with
spreaders (top lift and side lift), used for interchangeable carriages, semi-trailers or
other carrying device, for handling of container.
This document does not specify requirements for industrial variable-reach trucks (see
ISO 22915-11) and off-road industrial variable-reach trucks (see ISO 22915-14).
This document does not apply to forklifts handling containers, which have a movable
center of gravity (see ISO 3874).
This document does not apply to counterbalanced forklifts, which have gantry, for
handling freight containers (see ISO 22915-9).
2 Normative references
The contents of the following documents constitute essential provisions of this
document through normative references in the text. For the dated documents, only the
versions with the dates indicated are applicable to this document; for the undated
documents, only the latest version (including all the amendments) is applicable to this
standard.
GB/T 10827.2-2021 Industrial trucks - Safety requirements and verification - Part 2:
Self-propelled variable-reach trucks (ISO 3691-2:2016, IDT)
ISO 1496-2 Series 1 freight containers - Specification and testing - Part 2: Thermal
containers
Note: GB/T 7392-1998 Series 1 thermal containers - Specification and testing (idt ISO
1496-2:1996)
ISO 3874 Series 1 freight containers - Handling and securing
Note: GB/T 17382-2008 Series 1 freight containers - Handling and securing (ISO
3874:1997, IDT)
ISO 5353 Earth-moving machinery, and tractors and machinery for agriculture and
forestry - Seat index point
Note: GB/T 6236-2008 Tractors and machinery for agricultural and forestry - Seat index
point (ISO 5353:1995, MOD)
ISO 22915-1 Industrial trucks - Verification of stability - Part 1: General
Note: GB/T 26949.1-2020 Industrial trucks - Verification of stability - Part 1: General (ISO
22915-1:2016, IDT)
ISO 22915-10 Industrial trucks - Verification of stability - Part 10: Additional
stability tests for trucks operating in the special conditions of stacking with load
laterally displaced by powered devices
Note: GB/T 26949.10-2011 Industrial trucks - Verification of stability - Part 10: Additional
stability tests for trucks operating in the special conditions of stacking with load laterally
displaced by power (ISO 22915-10:2008, IDT)
ISO 22915-20 Industrial trucks - Verification of stability - Part 20: Additional
stability test for trucks operating in the special condition of offset load, offset by
utilization
Note: GB/T 26949.20-2016 Industrial trucks - Verification of stability - Part 20: Additional
stability test for trucks operating in the special condition of offset load, offset by utilization
(ISO 22915-20:2008, IDT)
3 Terms and definitions
The terms and definitions, which are defined in ISO 22915-1, as well as the following
terms and definitions, apply to this document.
3.1
Industrial variable-reach truck for handling freight containers
A counterbalanced forklift, which is equipped with a telescopic or non-telescopic,
non-slewing articulated arm, as defined in 4.13.2.2.2 of ISO 5053:1987, AND
specially used for handling freight containers of 6 m length and longer.
Note 1: The handling device is directly installed on the lifting mechanism; the lifting
mechanism cannot be slewed OR the slewing angle on either side of the longitudinal axis
of the vehicle is not greater than 5°.
Note 2: The industrial variable-reach truck for handling freight containers is expected to be
used on a firm, flat, level and paved site.
Note 3: According to the definition in GB/T 10827.2-2021, the industrial variable-reach
truck for handling freight container can be equipped with stabilizers, axle locking devices
or frame lateral leveling devices.
4 Operating conditions
4.1 General
In addition to the conditions specified in ISO 22915-1, it shall also meet the following
conditions:
- Operate the forklift in a wind speed not exceeding 12.2 m/s (freight containers run
and stack at normal operating height).
4.2 Partial lifting of containers
Before running, lift the container, so that the bottom of the container is not higher than
900 mm, above the seat index point (SIP) as defined in ISO 5353; meanwhile, the boom
is fully retracted.
Note: A lifted container allows an operator, who is at lower position on the vehicle, to see the
bottom of the container.
5 Test conditions
5.1 General
See ISO 22915-1.
During the test, it shall consider the eccentric load of the container, which is specified
in ISO 3874.
When handling an empty reefer container, which has an integrated refrigeration unit
(refrigerator) as specified in ISO 1496-2, it shall consider the offset load, in accordance
with the requirements of ISO 22915-20.
5.2 Prevailing wind
The test shall not be carried out in prevailing wind; otherwise, the test results will be
greatly affected.
5.3 Wind force
5.5.1 General
The test load shall consist of a base load, which is commensurate with the mass of the
container, AND a load or force, which simulates the wind acting on the container.
5.5.2 Basic load
The test load shall be equivalent to a 2.90 m (9 ft 6 in) high ISO standard container, the
mass of which is equivalent to the rated lifting weight, which is specified by the
manufacturer; it acts on the center of mass.
When using a top lifting, side lifting or other load handling device, the position of the
center of mass shall be determined by its connection point with the test load, such as
the connection point, where the twist lock enters the corner piece.
If the load handling device has a lateral adjustment function, as relative to the
longitudinal centerline of the vehicle, it shall comply with the provisions of ISO 22915-
10.
If the load handling device has a position adjustment function, in the direction of the
longitudinal centerline of the vehicle, in addition to the extension of the boom, the test
shall be carried out, at both extreme positions within the adjustment range.
5.5.3 Wind force
The effects of wind force can be simulated in the test, by one of the following methods:
- Apply the force to the center of mass of the load, at the same vertical angle (parallel
to the surface of the tilting platform) as the tilting platform, which is specified in
Table 1, in a direction perpendicular to the tipping axis of the forklift;
- When the inclination angle of the tilting platform reaches the inclination angle,
which is specified in Table 1, in addition to the test load, apply another vertical
load, whose moment is equivalent to the wind action.
5.6 Lifting height
5.6.1 Lifting height when simulating stacking test
When simulating the stacking test, the test load shall be in the combination state of
lifting and extending, that is most unfavorable to the stability of the vehicle, as specified
by the manufacturer.
During test 5 (see Table 1), the boom shall be at the maximum lifting angle, AND at the
maximum and minimum extension states, respectively.
5.6.2 Lifting height when simulating the running test with containers
When simulating the running test 2 and test 4 (see Table 1) with container, the boom
shall be fully retracted AND the center of mass of the test load shall be located 2350
mm, above the seat index point (SIP), which is defined in ISO 5353.
This lifting height is not suitable for vehicles, that have sufficient visibility in the
running direction without lifting the container, such as the operator in a high position
or running backwards (with the container behind). In these cases, the load shall be at
the actual position, which is specified by the manufacturer.
5.6.3 Lifting height in simulated running test without container
When simulating the running test without a container, the bottom of the load handling
device shall be located 900 mm above the seat index point (SIP), which is defined in
ISO 5353; the boom is fully retracted.
6 Verification of stability
The stability of the vehicle shall be verified, according to Table 1.
When conducting test 4 and test 5, the wheels shall not lose contact with the tilting
platform or any structural component; any part of the vehicle shall not contact the tilting
platform.
7 Markings
The actual lifting weight of the container handling, which is determined by the stability
test, shall be marked on the signboard, in accordance with the provisions of 6.3 in GB/T
10827.2-2021.
The additional lifting capacity (see 5.4), which is determined by the stability test with
stabilizers and/or axle locking devices, shall be indicated on the signboard.
When the wind speed, which is used for calculation, in accordance with 5.3, is greater
than the rated wind speed of 12.2 m/s, it shall mark the actual wind speed used for the
calculation.
......
Source: Above contents are excerpted from the full-copy PDF -- translated/reviewed by: www.ChineseStandard.net / Wayne Zheng et al.
Tips & Frequently Asked QuestionsQuestion 1: How long will the true-PDF of English version of GB/T 26949.12-2021 be delivered?Answer: The full copy PDF of English version of GB/T 26949.12-2021 can be downloaded in 9 seconds, and it will also be emailed to you in 9 seconds (double mechanisms to ensure the delivery reliably), with PDF-invoice. Question 2: Can I share the purchased PDF of GB/T 26949.12-2021_English with my colleagues?Answer: Yes. The purchased PDF of GB/T 26949.12-2021_English will be deemed to be sold to your employer/organization who actually paid for it, including your colleagues and your employer's intranet. Question 3: Does the price include tax/VAT?Answer: Yes. Our tax invoice, downloaded/delivered in 9 seconds, includes all tax/VAT and complies with 100+ countries' tax regulations (tax exempted in 100+ countries) -- See Avoidance of Double Taxation Agreements (DTAs): List of DTAs signed between Singapore and 100+ countriesQuestion 4: Do you accept my currency other than USD?Answer: Yes. www.ChineseStandard.us -- GB/T 26949.12-2021 -- Click this link and select your country/currency to pay, the exact amount in your currency will be printed on the invoice. Full PDF will also be downloaded/emailed in 9 seconds. How to buy and download a true PDF of English version of GB/T 26949.12-2021?A step-by-step guide to download PDF of GB/T 26949.12-2021_EnglishStep 1: Visit website https://www.ChineseStandard.net (Pay in USD), or https://www.ChineseStandard.us (Pay in any currencies such as Euro, KRW, JPY, AUD).
Step 2: Search keyword "GB/T 26949.12-2021".
Step 3: Click "Add to Cart". If multiple PDFs are required, repeat steps 2 and 3 to add up to 12 PDFs to cart.
Step 4: Select payment option (Via payment agents Stripe or PayPal).
Step 5: Customize Tax Invoice -- Fill up your email etc.
Step 6: Click "Checkout".
Step 7: Make payment by credit card, PayPal, Google Pay etc. After the payment is completed and in 9 seconds, you will receive 2 emails attached with the purchased PDFs and PDF-invoice, respectively.
Step 8: Optional -- Go to download PDF.
Step 9: Optional -- Click Open/Download PDF to download PDFs and invoice.
See screenshots for above steps: Steps 1~3 Steps 4~6 Step 7 Step 8 Step 9
|